HP LP2065 20" - Manual

2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source andconnection appropriate for this monitor. For information on the correct power cord set to use with themonitor, refer to the Power Cord Set R...

Maintenance Guidelines To enhance the performance and extend the life of the monitor: ● Do not open the monitor cabinet or attempt to service this product yourself. Adjust only thosecontrols that are covered in the operating instructions. If the monitor is not operating properly orhas been dropped o...

3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and otherattached devices, then follow the instructions below. NOTE: Be sure the master power switch, located on the rear panel of the monitor, is in the off position. The master powe...

Selecting the Signal Connectors and Cables The monitor features two DVI-I connectors capable of supporting either analog or digital input. The video mode supported by the DVI-I connector is determined by the video cable used. ● For digital operation, use the DVI-D signal cable provided. Connect the ...

Connecting the Monitor 1. Place the monitor in a convenient, well-ventilated location near the computer. 2. Connect one end of the USB hub cable to the USB connector on the rear panel of the computer,and the other end to the upstream USB connector on the monitor. Figure 3-5 Connecting the USB Cable ...

4. Place the cables through the cable management channel on the back of the monitor base. Figure 3-7 Using the Cable Management Feature Adjusting the Monitor 1. Tilt the monitor's panel forward or backward to set it to a comfortable eye level. Figure 3-8 Tilting the Monitor NOTE: The 24" model h...

4. Pivot the monitor from landscape to portrait orientation viewing to adapt to your application. Figure 3-11 Pivoting the Monitor NOTE: The 20" model (shown above) pivots counter-clockwise; the 19" and 24" models pivot clockwise. To view information on the screen in portrait mode, you w...

Connecting USB Devices The monitor provides four USB connectors, two on the side panel and two on the rear panel, used toconnect devices such as a digital camera, USB keyboard, or USB mouse. NOTE: You must connect the USB hub cable from the monitor to the computer to enable the USB 2.0 ports on the ...

Using the Accessory Rails The monitor features accessory rails on the rear that may be used to mount optional devices, such asthe HP speaker bar, to attach to the LCD. Refer to the documentation included with the optional devicefor detailed mounting instructions. Figure 3-13 Using the Accessory Rail...

3. Pull up on the monitor display head (2) to remove it from the base. Figure 3-14 Removing the Monitor from the Pedestal Base Mounting the Monitor The HP Quick Release can be removed from the pedestal base and installed to a mounting fixture. Itallows you to quickly and securely attach the monitor ...

4 Operating the Monitor Software and Utilities The CD that comes with the monitor contains files you can install on the computer: ● an .INF (Information) file ● an .ICM (Image Color Matching) file ● auto-adjustment pattern utility ● additional software for the monitor model Adobe Reader is supplied ...

Installing the .INF and .ICM Files After you determine that you need to update, you can install the .INF and .ICM files from the CD ordownload them. Installing from the CD To install the .INF and .ICM files on the computer from the CD: 1. Insert the CD in the computer CD-ROM drive. The CD menu is di...

Using the Auto-Adjustment Function You can optimize the screen performance for the VGA (analog) input by using the -/Auto button on the monitor and the auto-adjustment pattern software utility on the CD provided. Do not use this procedure if the monitor is using a DVI input. If the monitor is using ...

Front Panel Controls Table 4-1 Monitor Front Panel Controls Control Function 1 Menu/Select Opens, selects or exits the OSD menu. 2 – (Minus)/Auto ● Navigates backward through the OSD menu anddecreases adjustment levels. ● When the OSD menu is inactive, activates the autoadjustment feature to optimiz...

Adjusting the Monitor Settings The monitor settings can be adjusted from the On-Screen Display (OSD) menu or from the HP DisplayAssistant utility. Using the On-Screen Display Menu Use the On-Screen Display (OSD) to adjust the screen image based on your viewing preferences. Toaccess the OSD, do the f...

Optimizing Digital Conversion This monitor contains advanced circuitry that allows the flat panel screen to function like a standardmonitor. Two controls in the on-screen display can be adjusted to improve image performance: Clockand Clock Phase. NOTE: The Clock and Clock Phase controls are adjustab...

Identifying Monitor Conditions Special messages will appear on the monitor screen when identifying the following monitor conditions: ● Input Signal Out of Range—Change resolution setting to 1280 × 1024 – 60Hz (LP1965 19" model), 1600 × 1200 - 60Hz (LP2065 20" model), or 1920 × 1200 - 60 Hz (...

NOTE: You must set the current local time before you reset the time for Sleep Time or On Time . Note that the time is displayed in a 24–hour clock format. For example, 1:15 p.m. is displayed as 13 hours 15 minutes. 5. Press the Menu button once to enter the adjustment mode for hours. 6. Press the - ...

Select This Option To Do This Display On Sets the time when the monitor automatically turns on. This does not affect screensaver operation, which has priority over the HP Display LiteSaver. Activity Extension Sets the time in minutes before the monitor turns off if there is any keyboard or mouseacti...

A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommendedsolutions. Problem Possible Cause Solution Screen is blank. Power cord is disconnected. Connect the power cord. Power switch on front panel of themonitor is t...

Problem Possible Cause Solution HP Display LiteSaverdoesn't turn off the monitorscreen. The Activity Extension time has notelapsed. The default Activity Extension value is set to 10 minutes.The HP Display LiteSaver will wait to detect no input ormovement from the keyboard or mouse for 10 consecutive...

B Technical Specifications NOTE: All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP's component manufacturers' typical levelspecifications for performance and actual performance may vary either higher o...

Recognizing Preset Display Resolutions The display resolutions listed below are the most commonly used modes and are set as factory defaults.This monitor automatically recognized these preset modes and they will appear properly sized andcentered on the screen. Table B-4 LP1965 Model Factory Preset M...

*24 1920 × 1200 74.6 60.0 *For analog inputs only. Entering User Modes The video controller signal may occasionally call for a mode that is not preset if: ● You are not using a standard graphics adapter. ● You are not using a preset mode. It this occurs, you may need to readjust the parameters of th...

C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a resid...

German Ergonomics Notice HP products which bear the “GS” approval mark, when forming part of a system comprising HP brandcomputers, keyboards and monitors that bear the “GS” approval mark, meet the applicable ergonomicrequirements. The installation guides included with the products provide configura...

Product Environmental Notices Materials Disposal This HP product contains mercury in the fluorescent lamp in the display LCD that might require specialhandling at end-of-life. Disposal of this material can be regulated because of environmental considerations. For disposal orrecycling information, co...

D LCD Monitor Quality and Pixel Policy The TFT monitor uses high-precision technology, manufactured according to HP standards, toguarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections thatappear as small bright or dark spots. This is common to all LCD displays ...