HP LP3065 - Manual

2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source andconnection appropriate for this monitor. For information on the correct power cord set to use with themonitor, refer to the Power Cord Set R...

Maintenance Guidelines To enhance the performance and extend the life of your monitor: ● Do not open your monitor cabinet or attempt to service this product yourself. Adjust only thosecontrols that are covered in the operating instructions. If your monitor is not operating properly orhas been droppe...

3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and otherattached devices, then follow the instructions below. NOTE Be sure the master power switch, located on the rear panel of the monitor, is in the off position. The master power...

Selecting the Signal Connectors and Cables The monitor features two DVI-D dual-link connectors capable of supporting high resolution digital input. NOTE The high resolution of the monitor requires a dual-link DVI-D input signal. The monitor can only display a 2560 x 1600 resolution; therefore, the c...

Connecting the Monitor 1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Connect one end of the USB hub cable to the USB connector on the rear panel of the computer,and the other end to the upstream USB connector on the monitor. Figure 3-4 Connecting the USB Cable...

Adjusting the Monitor 1. Adjust the monitor's panel forward or backward to set it to a comfortable eye level. Figure 3-7 Tilting the Monitor 2. Swivel the monitor to the left or right for the best viewing angle. Figure 3-8 Swiveling the Monitor ENWW Adjusting the Monitor 9

Turning on the Monitor 1. Press the power switch to turn on the computer. 2. Press the master power switch on the rear of the LCD. 3. Press the power button on the front of the monitor. CAUTION Burn-in image damage may occur on monitors that display the same static image on screen for a prolonged pe...

Figure 3-11 Using the Accessory Rails Feature Removing the Monitor Pedestal Base You can remove the monitor pedestal to mount the monitor on a wall, a swing arm, or other mountingfixture. CAUTION Before beginning to disassemble the monitor, be sure the monitor is turned off and the power and signal ...

Mounting the Monitor 1. Remove the monitor pedestal base. Refer to Removing the Monitor Pedestal Base in the previous section. CAUTION This monitor supports the VESA industry standard 100mm mounting holes. To attach a third party mounting solution to the monitor, four 4mm, 0.7 pitch, and 10mm longsc...

4 Operating the Monitor Software and Utilities The CD that comes with the monitor contains files you can install on your computer: ● an .INF (Information) file ● an .ICM (Image Color Matching) file ● additional software for the monitor model Adobe Reader is supplied on this CD and can be installed f...

Installing from the CD To install the .INF and .ICM files on the computer from the CD: 1. Insert the CD in the computer CD-ROM drive. The CD menu displays. 2. View the “Monitor Driver Software Readme” file. 3. Select “Install Monitor Driver Software.” 4. Follow the on-screen instructions. 5. After t...

NOTE The monitor does not support an On-Screen Display (OSD) menu. HP Display LiteSaver HP Display LiteSaver is a software application, available on the CD, that increases monitor life andsaves energy. It allows you to place your monitor into its low power sleep mode at predefined times byshutting d...

A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommendedsolutions. Problem Possible Cause Solution Screen is blank and noLED. No AC power. Connect the power cable connections and make sure the master powerswitch is...

B Technical Specifications NOTE All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP's componentmanufacturers' typical level specifications for performance and actual performance may varyeither higher or ...

Altitude: Operating Storage 0 to 12,000 feet 0 to 40,000 feet 0 to 3657.6 m 0 to 12192 m Power Consumption (maximum) <176 watts Input Terminal Three DVI-D connectorswith two DVI-D cablesincluded. Energy Saver Feature When the monitor is in its normal operating mode, the monitor uses <176 watts...

C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a resid...

Hewlett Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call 1-800-HP-INVENT (1-800 474-6836) For questions regarding this FCC declaration, contact: Hewlett Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333 To identi...

Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany Japanese Notice Korean Notice Power Cord Set Requirements The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows themonitor to operate on input voltages between 100–120V or 200–24...

Product Environmental Notices Materials Disposal This HP product contains the following materials that might require special handling at end-of-life: ● Mercury in the fluorescent lamp in the display LCD. ● Lead in the solder and some component leads. Disposal of this material can be regulated becaus...