HP LP1965 - Manual

2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source and connection appropriate for this monitor. For information on the correct power cord set to use with the monitor, refer to the Power Cord Set...

Maintenance Guidelines To enhance the performance and extend the life of the monitor: ● Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those controls that are covered in the operating instructions. If the monitor is not operating properly or has been dropped...

3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow the instructions below. NOTE Be sure the master power switch, located on the rear panel of the monitor, is in the off position. The master powe...

Selecting the Signal Connectors and Cables The monitor features two DVI-I connectors capable of supporting either analog or digital input. The video mode supported by the DVI-I connector is determined by the video cable used. ● For digital operation, use the DVI-D signal cable provided. Connect the ...

Connecting the Monitor 1. Place the monitor in a convenient, well-ventilated location near the computer. 2. Connect one end of the USB hub cable to the USB connector on the rear panel of the computer, and the other end to the upstream USB connector on the monitor. Figure 3-5 Connecting the USB Cable...

Adjusting the Monitor 1. Tilt the monitor's panel forward or backward to set it to a comfortable eye level. Figure 3-8 Tilting the Monitor NOTE The 24" model has a tilt range of -5 to +25 degrees. 2. Swivel the monitor to the left or right for the best viewing angle. Figure 3-9 Swiveling the Mon...

4. Pivot the monitor from landscape to portrait orientation viewing to adapt to your application. Figure 3-11 Pivoting the Monitor NOTE The 20" model (shown above) pivots counter-clockwise; the 19" and 24" models pivot clockwise. To view information on the screen in portrait mode, you wi...

Connecting USB Devices The monitor provides four USB connectors, two on the side panel and two on the rear panel, used to connect devices such as a digital camera, USB keyboard, or USB mouse. NOTE You must connect the USB hub cable from the monitor to the computer to enable the USB 2.0 ports on the ...

Using the Accessory Rails The monitor features accessory rails on the rear that may be used to mount optional devices, such as the HP speaker bar, to attach to the LCD. Refer to the documentation included with the optional device for detailed mounting instructions. Figure 3-13 Using the Accessory Ra...

3. Pull up on the monitor display head (2) to remove it from the base. Figure 3-14 Removing the Monitor from the Pedestal Base Mounting the Monitor The HP Quick Release can be removed from the pedestal base and installed to a mounting fixture. It allows you to quickly and securely attach the monitor...

4 Operating the Monitor Software and Utilities The CD that comes with the monitor contains files you can install on the computer: ● an .INF (Information) file ● an .ICM (Image Color Matching) file ● auto-adjustment pattern utility ● additional software for the monitor model Adobe Reader is supplied ...

Installing the .INF and .ICM Files After you determine that you need to update, you can install the .INF and .ICM files from the CD or download them. Installing from the CD To install the .INF and .ICM files on the computer from the CD: 1. Insert the CD in the computer CD-ROM drive. The CD menu is d...

Using the Auto-Adjustment Function You can optimize the screen performance for the VGA (analog) input by using the -/Auto button on the monitor and the auto-adjustment pattern software utility on the CD provided. Do not use this procedure if the monitor is using a DVI input. If the monitor is using ...

Front Panel Controls Table 4-1 Monitor Front Panel Controls Control Function 1 Menu/Select Opens, selects or exits the OSD menu. 2 – (Minus)/Auto ● Navigates backward through the OSD menu and decreases adjustment levels. ● When the OSD menu is inactive, activates the auto adjustment feature to optim...

Adjusting the Monitor Settings The monitor settings can be adjusted from the On-Screen Display (OSD) menu or from the HP Display Assistant utility. Using the On-Screen Display Menu Use the On-Screen Display (OSD) to adjust the screen image based on your viewing preferences. To access the OSD, do the...

OSD Menu Selections The following table lists the On-Screen Display (OSD) menu selections and their functional descriptions. After changing an OSD menu item, and if the menu screen has these options, you may choose to: ● Cancel —to return to the previous menu level. ● Save and Return —to save all ch...

Optimizing Digital Conversion This monitor contains advanced circuitry that allows the flat panel screen to function like a standard monitor. Two controls in the on-screen display can be adjusted to improve image performance: Clock and Clock Phase. NOTE The Clock and Clock Phase controls are adjusta...

Identifying Monitor Conditions Special messages will appear on the monitor screen when identifying the following monitor conditions: ● Input Signal Out of Range—Change resolution setting to 1280 × 1024 – 60Hz (LP1965 19" model), 1600 × 1200 - 60Hz (LP2065 20" model), or 1920 × 1200 - 60 Hz (...

NOTE You must set the current local time before you reset the time for Sleep Time or On Time . Note that the time is displayed in a 24–hour clock format. For example, 1:15 p.m. is displayed as 13 hours 15 minutes. 5. Press the Menu button once to enter the adjustment mode for hours. 6. Press the - (...

Table 4-3 HP Display LiteSaver Configuration Options (continued) Select This Option To Do This Display Off Sets the time when the monitor automatically turns off. This does not affect screen saver operation, which has priority over the HP Display LiteSaver. Display On Sets the time when the monitor ...

A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommended solutions. Problem Possible Cause Solution Screen is blank. Power cord is disconnected. Connect the power cord. Power switch on front panel of the monitor is...

Problem Possible Cause Solution HP Display LiteSaver doesn't turn off the monitor screen. The Activity Extension time has not elapsed. The default Activity Extension value is set to 10 minutes. The HP Display LiteSaver will wait to detect no input or movement from the keyboard or mouse for 10 consec...

B Technical Specifications NOTE All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP's component manufacturers' typical level specifications for performance and actual performance may vary either higher o...

Recognizing Preset Display Resolutions The display resolutions listed below are the most commonly used modes and are set as factory defaults. This monitor automatically recognized these preset modes and they will appear properly sized and centered on the screen. Table B-4 LP1965 Model Factory Preset...

Table B-6 LP2465 Model Factory Preset Modes (continued) 23 1920 × 1200 74.0 60.0 *24 1920 × 1200 74.6 60.0 *For analog inputs only. Entering User Modes The video controller signal may occasionally call for a mode that is not preset if: ● You are not using a standard graphics adapter. ● You are not u...

C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a res...

Japanese Power Cord Requirements For use in Japan, use only the power cord received with this product. CAUTION Do not use the power cord received with this product on any other products. Product Environmental Notices Materials Disposal This HP product contains mercury in the fluorescent lamp in the ...

D LCD Monitor Quality and Pixel Policy The TFT monitor uses high-precision technology, manufactured according to HP standards, to guarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections that appear as small bright or dark spots. This is common to all LCD display...