Honeywell Switches- User Manual

Page 2 - SWITCH APPLICATIONS; CONTENTS; WARNING

2 SWITCH APPLICATIONS CONTENTS • Ultra Duty Pressure Switches 10-400 psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.3• Extended Duty Pressure Switches 0.5-150 psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.4• Extended Duty Vacuum Switches1.1-22” Hg . ....

Page 3 - Specifications; Ultra Duty Pressure Switch; Approximate Dead Band

5000 Series Ultra Duty 2 Terminals Metri-Pack Integral Connector Pressure Switches (See Note 1) Contact Factory Circuitry Screw Blade Contact Factory Circuitry Part # Setting Set At Part # Part # Setting Set At N.O. 83298 83313 N.O. 83328 10-35 PSI 20 PSI N.C. 83299 83314 10-30 PSI 20 PSI N.C. 83329...

Page 4 - Extended Duty Pressure Switch With Direct Action Blade Contacts; for Vacuum and Pressure; Standard Specifications

1.47” REF. The 5000 Series switch is specifically designed to stand up to extended duty applications. This switch is factory set but capable of field adjustment. It features a Kapton diaphragm for compatibility with a wide variety of fluids, and various terminations including a Metri-Pack connector ...

Page 5 - 000 Series Pressure Switch With Standard Terminal; 000 Series Pressure Switch With Metri-Pack Terminal

5 Single Circuit 1 Terminal 3. The tolerances given in the table are applicable to a switch adjusted so that the N.O. circuit closes before the N.C. circuit opens and applies to the N.C. circuit. The N.O. set point and tolerances are such that a minimum overlap of 1 PSI exists during which both circ...

Page 6 - Set Points from 1.1” to 22” Hg; Extended Duty Vacuum Switches With Direct Action Blade Contacts; with Screw Terminals

6 Set Points from 1.1” to 22” Hg 5000 Series Extended Duty Vacuum Switches With Direct Action Blade Contacts 5000 Series Vacuum Switch Circuitry Contact Setting Part Number Internally Grounded Two Terminals Part Number 1.1-22” Hg N.O. N.C. 7881378815 7881478816 Screw Blade Screw Blade 7734277343 773...

Page 7 - Extended Duty Piston Switches With Direct Action Blade Contacts

7 The 5000 Series piston switch is specifically designed for extended duty applications with set point requirements from 200 to 1000 PSI. This switch is factory set with various terminations available including a Metri-Pack connector that forms a tight seal when connected. Among the outstanding desi...

Page 8 - Set Points from 2 to 70 psi and 2” to 22” Hg; Series III

8 Set Points from 2 to 70 psi and 2” to 22” Hg Series III Factory Set Variable Differential Pressure & Vacuum Switches With Snap Action Contacts The Series III switch is a customizable switch built per customer specifications. It features a non-ferrous chamber and excellent set point integrity a...

Page 9 - Series V; Diaphragm Type; Piston Type

9 Set Points from 35 to 3000 psi Series V High Pressure Environmentally Sealed, Extreme-Duty Switches With Snap Action Contacts 1.187” REF. 1.187” REF. Diaphragm Type Set Point Range Differential 26900269012690226903 35-50 PSI 50-100 PSI 100-200 PSI200-300 PSI 10-15 PSI10-15 PSI10-15 PSI10-20 PSI Re...

Page 10 - Conversion Factors; Switch Definitions and Terminology

Pressure/Vacuum Switch - A device that senses a change in pressure/vacuum and opens or closes an electrical circuit when the set point is reached. Set Point - The pre-determined pressure/vacuum value that is required to open or close the electrical contacts in the switch. Electrical Contacts - The e...

Page 12 - The foregoing is Buyer’s sole remedy and is; Sales and Service; For Honeywell pressure and vacuum switches

Sensing and Control Honeywell P.O. Box 19424 Springfield, IL 62794-9424 USA email: [email protected] www.honeywell.com/hobbs Catalog 10-1003, GLO Printed in the U.S.A. © 2004 Honeywell International Inc. All Rights Reserved. Warranty/Remedy Honeywell warrants goods of its manufacture as being free o...

Honeywell Switches- User Manual

Table of Contents:

Other Manuals for Honeywell Switches

Summary

Other Honeywell Models