Hobart 400 - Manual - manualsarea.com

Page 2 - From Hobart to You

Hobart Welders manufactures a full lineof welders and welding related equipment.For information on other quality Hobart products, contact your local Hobartdistributor to receive the latest full line catalog or individual catalog sheets.To locate your nearest distributor or service agency call 1-877-...

Page 3 - TABLE OF CONTENTS

TABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 6 - FUMES AND GASES can be hazardous

OM-203 653 Page 2 D On inverter power sources, failed parts can ex- plode or cause other parts to explode when power is applied. Always wear a face shield and long sleeves when servicing inverters. EXPLODING PARTS can injure. Sparks and hot metal blow out from the cutting arc. Chipping and grinding ...

Page 7 - ARC CUTTING can cause interference.

OM-203 653 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance HOT PARTS can cause severe burns. D Do not touch hot parts bare handed. D Allow cooling period before working on torch. MOVING PARTS can cause injury. D Keep away from moving parts such as fans. D Keep all doors, ...

Page 9 - LE COUPAGE présente un risque de

OM-203 653 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION pom_fre 5/04 2-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette procédure présente des risques de danger ! Ceux-ci sont identifiés par des symboles adjacents aux directives. Y Identifie un messa...

Page 11 - et la maintenance; Danger D’EXPLOSION

OM-203 653 Page 7 Les bouteilles de gaz contiennent du gaz sous haute pression. Si une bouteille est endommagée, elle peut exploser. Puisque les bouteilles de gaz font habituellement partie d’un processus de travail des métaux, assurez − vous de les manipuler correctement. LES BOUTEILLES peuvent exp...

Page 12 - -5. Information sur les champs électromagnétiques

OM-203 653 Page 8 2-4. Principales normes de sécurité Safety in Welding and Cutting, norme ANSI Z49.1, de l’American Wel- ding Society, 550 N.W. Lejeune Rd, Miami FL 33126 Safety and Health Sandards, OSHA 29 CFR 1910, du Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. ...

Page 13 - IP; pf

OM-203 653 Page 9 SECTION 3 − DEFINITIONS 3-1. Symbols And Definitions For Nameplate And Serial Number/Rating Label A Amperes Plasma Arc Cutting (PAC) Adjust Air/Gas Pressure Low Air Pressure Light V Volts Increase No − Do Not Do This Temperature Protective Earth (Ground) Single Phase Constant Curre...

Page 19 - ON

OM-203 653 Page 15 SECTION 5 − OPERATION 5-1. Controls 1 4 2 3 5 ON OFF PRESSURE 60 PSI 5 6 24 27 6 Set To 60 PSI (414 kPa) 20 16 24 27 20 16 1 24 27 20 16 Requires 70-150 PSI (483-1034 kPa) Supply Setting Gas/Air Pressure 1 Output Control Use control to set cutting output.Place control in Gas/Air S...

Page 22 - Each Use

OM-203 653 Page 18 SECTION 6 − MAINTENANCE & TROUBLESHOOTING 6-1. Routine Maintenance Y Disconnect power before maintaining. . Maintain more oftenduring severe conditions. Each Use Check Gas/Air Pressure Check Torch Tip, Electrode, And Shield Cup Every Week Check Shield Cup Shutdown System 3 Mon...

Page 29 - Notes

Page 36 - Hobart Welding Products; Please complete and retain with your personal records.; To locate a Distributor,; Contact your Distributor for:; Resources Available; For technical assistance:

PRINTED IN USA  2004 Hobart Welding Products. 1/04 Hobart Welding Products An Illinois Tool Works Company 600 West Main Street Troy, OH 45373 USA For Technical Assistance: Call1-800-332-3281 For Literature Or Nearest Dealer: Call 1-877-Hobart1 Model Name Serial/Style Number Purchase Date (Date whic...

Hobart 400 - Manual

Table of Contents:

Summary

Other Hobart Models