Hitachi 8000 Elite - Manual

Keyboard Figure 1-5 Keyboard Components Table 1-4 Keyboard Components 1 Function Keys Perform special functions depending on the software application being used. 2 Editing Keys Includes the following: Insert, Home, Page Up, Delete, End, and Page Down. 3 Status Lights Indicate the status of the compu...

Windows Logo Key + + (on numpad) Zooms in Windows Logo Key + - (on numpad) Zooms out Serial Number Location Each computer has a unique serial number and a product ID number that are located on the top coverof the computer. Keep these numbers available for use when contacting customer service for ass...

2 Hardware Upgrades Serviceability Features The computer includes features that make it easy to upgrade and service. No tools are needed for mostof the installation procedures described in this chapter. Warnings and Cautions Before performing upgrades be sure to carefully read all of the applicable ...

Unlocking the Smart Cover Lock NOTE: The Smart Cover Lock is an optional feature included on some models only. The Smart Cover Lock is a software-controllable cover lock, controlled by the setup password. This lockprevents unauthorized access to the internal components. The computer ships with the S...

Removing the Computer Access Panel 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn off any external devi...

Replacing the Computer Access Panel 1. Lay the computer down on its large base for greater stability. 2. Slide the lip on the front end of the access panel under the lip on the front of the chassis (1) thenpress the back end of the access panel onto the unit so that it locks into place (2). Figure 2...

Removing the Front Bezel 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4. Di...

Removing Bezel Blanks 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4. Disco...

Installing Additional Memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3-SDRAM) dual inline memory modules (DIMMs). DIMMs The memory sockets on the system board can be populated with up to four industry-standard DIMMs.These memory sockets are populated w...

Populating DIMM Sockets There are four DIMM sockets on the system board, with two sockets per channel. The sockets arelabeled XMM1, XMM2, XMM3, and XMM4. Sockets XMM1 and XMM2 operate in memory channel A.Sockets XMM3 and XMM4 operate in memory channel B. Figure 2-7 DIMM Socket Locations Table 2-1 DI...

will have more memory than the other, the larger amount should be assigned to Channel A. Forexample, if you are populating the sockets with one 2-GB DIMM, and three 1-GB DIMMs, ChannelA should be populated with the 2-GB DIMM and one 1-GB DIMM, and Channel B should bepopulated with the other two 1-GB...

Removing or Installing an Expansion Card The computer has three standard full-height PCI expansion slots, one PCI Express x1 expansion slot,one PCI Express x16 expansion slot, and one PCI Express x16 expansion slot that is downshifted to ax4 slot. Figure 2-9 Expansion Slot Locations Table 2-2 Expans...

Removing a Drive from a Drive Bay CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the c...

Installing Additional Drives When installing additional drives, follow these guidelines: ● The primary Serial ATA (SATA) hard drive must be connected to the dark blue SATA connectoron the system board labeled SATA0. ● Connect the first SATA optical drive to the white SATA connector on the system boa...

Installing a 5.25-inch Drive into an External Drive Bay 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn ...

CAUTION: The bottom 5.25-inch drive bay has a shorter depth than the upper two bays. The bottom bay supports a half-height drive or other device that is no more than 14.5 cm (5.7 inches)in depth. Do not try to force a larger drive, such as an optical drive, into the bottom bay. This couldcause damag...

8. Connect the power cable (1) and data cable (2) to the rear of the hard drive. Figure 2-28 Connecting the Power Cable and Data Cable to a SATA Hard Drive 9. Connect the opposite end of the data cable to the appropriate system board connector. NOTE: If your system has only one SATA hard drive, you ...

Changing from a Minitower to a Desktop Configuration 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn off...

13. Reposition the subpanel (rotate it 90º) with the logo at the bottom, then snap it back into the bezel. Figure 2-39 Changing from a Minitower to a Desktop Configuration 14. Replace the front bezel and computer access panel. 15. Reconnect the power cord and turn on the computer. 16. Lock any secur...

B Battery Replacement The battery that comes with the computer provides power to the real-time clock. When replacing thebattery, use a battery equivalent to the battery originally installed in the computer. The computer comeswith a 3-volt lithium coin cell battery. WARNING! The computer contains an ...

C External Security Devices NOTE: For information on data security features, refer to the Desktop Management Guide and the HP ProtectTools Security Manager Guide (some models) at http://www.hp.com . Installing a Security Lock The security locks displayed below and on the following page can be used t...

Padlock Figure C-2 Installing a Padlock HP Business PC Security Lock 1. Fasten the security cable by looping it around a stationary object. Figure C-3 Securing the Cable to a Fixed Object 50 Appendix C External Security Devices ENWW

4. Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage thelock. Use the key provided to disengage the lock. Figure C-6 Engaging the Lock Front Bezel Security The front bezel can be locked in place by installing a security screw provided by HP. To install ...

D Electrostatic Discharge A discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices. This type of damage may reduce the life expectancy of the device. Preventing Electrostatic Damage To prevent electrostatic damage, observe the follo...

E Computer Operating Guidelines,Routine Care and Shipping Preparation Computer Operating Guidelines and Routine Care Follow these guidelines to properly set up and care for the computer and monitor: ● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ● O...

Optical Drive Precautions Be sure to observe the following guidelines while operating or cleaning the optical drive. Operation ● Do not move the drive during operation. This may cause it to malfunction during reading. ● Avoid exposing the drive to sudden changes in temperature, as condensation may f...

Index A access panel locking and unlocking 9, 49removing 11replacing 12 audio connectors 2, 4 B battery replacement 46 C changing computer configuration 39, 41 computer operating guidelines 55connecting drive cables 29 D desktop conversion 39DIMMs. See memory drive connectors 30drives connecting cab...