Page 3 - Keep appliance area free and clear from combustibles.
Model OFG- 390 This manual should be retained in a convenient location for future reference. A wiring diagram for this appliance is located on the rear shroud cover of the control panel. Post in a prominent location, instructions to be followed if user smells gas. This informationshould be obtained ...
Page 4 - SPECIFICATIONS
Model OFG- 390 HENNY PENNY 6 HEAD GAS OPEN FRYER SPECIFICATIONS Height 61" (155 cm) Width 24" (61 cm) Depth 41¾" ( 107 cm) Floor Space Approximately 7 sq. ft. (.65 sq. m.) Pot Capacity 6 Head of chicken - 20 lbs. (9 kg.)130 lbs. shortening (46 Kg.) Electrical 120 VAC, 1 Phase, 50/60 Hz, ...
Page 5 - 209 i; TABLE OF CONTENTS; Section
Model OFG- 390 1209 i TABLE OF CONTENTS Section Page Section 1. TROUBLESHOOTING ............................................................................................. 1-1 1-1 Introduction .................................................................................................... 1-1 ...
Page 7 - SECTION 1. TROUBLESHOOTING; NOTICE is used to highlight especially important information.
Model OFG- 390 1-1. INTRODUCTION This section provides troubleshooting information in the formof an easy to read table. If a problem occurs during the first operation of a new fryer,recheck the installation per the Installation Section of thismanual. Before troubleshooting, always recheck the operat...
Page 13 - • Spark ignitor or flame sensor out of
Model OFG- 390 Problem Cause Correction HEATING OF SHORTENING SECTION • Gas valve knob turned to the OFF • Make sure the gas valve knob is position turned to the ON position. • Blown fuse or tripped • Reset breaker or replace fuse circuit breaker at supply box or control panel • Blown fuse in PC boa...
Page 19 - Checkout
Model OFG- 390 2-4. HIGH TEMPERATURE LIMIT CONTROL This high temperature control is a safety, manual reset control,which senses the temperature of the shortening. If the shorteningtemperature exceeds 425°F (218°C), this switch opensand shuts off the heat to the frypot. When the temperature ofthe sho...
Page 20 - Replacement
Model OFG- 390 2-4. HIGH TEMPERATURE LIMIT CONTROL (Continued) Replacement To avoid electrical shock or property damage, move thePOWER switch to OFF and disconnect main circuitbreaker, or unplug cord at wall receptacle. 1. If the tube is broken or cracked, the control will open, shutting off electri...
Page 21 - LIMIT CONTROL; With excess capillary line pulled out, tighten smaller nut.; Label and remove wires from the switch.
Model OFG- 390 2-4. HIGH TEMPERATURE 11. Pull excess capillary line from pot and tighten nut into frypot wall. LIMIT CONTROL (Continued) Be sure capillary bulb of high limit is positioned so it doesn’tinterfere with the carrier or get damaged when cleaning thefrypot. 12. With excess capillary line p...
Page 23 - Excess force will damage temperature probe.; PANEL-HENNY PENNY
Model OFG- 390 2-6. TEMPERATURE PROBE 7. Tighten hand tight and then a half turn with wrench. REPLACEMENT (Continued) Excess force will damage temperature probe. 8. Connect new temperature probe to PC board and replace control panel. 9. Replace shortening. 10. Turn power on and check out fryer. 2-7....
Page 24 - CABLES
Model OFG- 390 2-8. LID COUNTERWEIGHT The Lid Counterweight in the back of the fryer balances the CABLES weight of the lid system to allow easier opening and closing ofthe lid. The weight has two cables attached to it, and weighsabout 100 lbs. (45.4 Kg). 1. Using a Phillips head screwdriver, remove ...
Page 26 - Remove the wires from the control valve.
Model OFG- 390 2-9. GAS CONTROL VALVE The gas control valve sends regulated gas to the burners when thecontroller calls for heat. The control valve can be turned onor off. In the on position, and the power switch on, a spark ignitorlights a standing pilot, and when the control calls for heat, the va...
Page 30 - Remove electrical power supplied to the unit.
Model OFG- 390 2-12. AIRFLOW SWITCH The airflow switch senses the flow of air coming from theblower. If the airflow is reduced below a set amount, theswitch will cut power to the control valve, which shuts theburners down. Replacement 1. Remove electrical power supplied to the unit. To avoid electri...
Page 34 - Dilution Box
Model OFG- 390 2-16. CLEANING THE Clean the dilution box monthly to ensure the unit operates DILUTION BOX efficiently and without failures. 1. Make sure unit is off, and close and lock the lid. Lid should be in locked down position. Failure to do socould result in personal injury. 2. Unscrew the win...
Page 35 - LED Indication; White Rogers
Model OFG- 390 2-18. IGNITION MODULES The ignition modules send 24 volts to the ignitors and gas valve. LED Indication Two different modules are in the field. The White Rogers moduleshave a red LED, and the Robershaw modules have a green LED.These LEDs help to identify a failure. For the White Roger...
Page 36 - • DISCONNECT THE MAIN CIRCUIT BREAKER AT
Model OFG- 390 2-19. IGNITOR ASSEMBLY The 390 has electronic spark ignition, that lights a standing pilot. Replacement 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move thePOWER switch to OFF and disconnect main circuitbreaker, or unplug cord at wall...
Page 37 - Ground Rod Flame Sensor
Model OFG- 390 2-20. FLAME SENSOR The flame sensor should glow a bright red when the pilot is lit and ASSEMBLY allows the gas valve to open. If it does not sense a flame, itshuts down the gas valve. Replacement 1. Remove electrical power supplied to the unit. To avoid electrical shock or property da...
Page 38 - Remove back and top shrouds; REPLACEMENT; Remove the screw and keps nut securing the nylatron to the
Model OFG- 390 2-22. NYLATRON STRIPS 1. Remove back and top shrouds REPLACEMENT 2. Remove the screw and keps nut securing the nylatron to the extension. 3. Remove the screws securing the guides, and slide the guides up and out from the top of the shroud. 4. Pull the broken piece from the unit. The n...
Page 46 - SECTION 3. PARTS INFORMATION; Item Number
Model OFG- 390 SECTION 3. PARTS INFORMATION 3-1. INTRODUCTION This section lists the replaceable parts of the Henny Penny ModelOFG-390. 3-2. GENUINE PARTS Use only genuine Henny Penny parts in your fryer. Using a part oflesser quality or substitute design may result in damage to the unit orpersonal ...
Page 48 - Description; FRAME & COVER ASSEMBLY; recommended parts
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-1 FRAME & COVER ASSEMBLY 1 39796 WELDMENT – CONTROL PANEL FRONT .......... 1 2 53669 GUARD – POWER SWITCH ................................... 1 √√√√√ 3 29898 SWITCH – POWER ................................................. 1 4 5560...
Page 49 - CONTROL PANEL
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-2 CONTROL PANEL √√√√√ 1 55765RB CONTROL ASSY - SMS – KFC 390 .................................... 1 √√√√√ 1 72164RB CONTROL ASSY - SMS -120V-KFC 390-W/O SETPTS-INT’L ......... 1 √√√√√ 1 55772RB CONTROL ASSY - SMS - 220-240V ..............
Page 50 - ELECTRICAL CONTROLS
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-3 ELECTRICAL CONTROLS √√√√√ 1 60207 TRANSFORMER ASSY – 120V ............................................. 1 √√√√√ 1 60536 TRANSFORMER ASSY – 24V/230V ...................................... 1 2 SC03-005 SCREW ..............................
Page 51 - FRYPOT COVERS AND INSULATION
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-4 FRYPOT COVERS AND INSULATION 1 52799 ASSY-INSUL/LFT. C/CHAMBER .......................................... 1 2 52041 INSULATION-C/CHAMBER MOUNTIN .............................. 4 3 52798 ASSY-INSUL/RT. C/CHAMBER .........................
Page 52 - INSULATION COVERS
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-5 INSULATION COVERS 1 WA02-001 WASHER – INSULATION 1-1/2” DIA. .................................. 17 2 51763 INSULATION COVER – LEFT ............................................... 1 3 51892 INSULATION – C/CHAMBER SIDE ...................
Page 53 - Figure 3-6. Drain Pan and Filter Assembly
Model OFG- 390 806 3-8 Figure 3-6. Drain Pan and Filter Assembly
Page 54 - DRAIN PAN AND FILTER ASSEMBLY
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-6 DRAIN PAN AND FILTER ASSEMBLY 1 52194 CRUMB CATCHER (OPTIONAL) ......................................... 1 2 03204 CRUMB CATCHER BASKET W/HANDLE (OPTIONAL) .... 1 2 21010 . “COLD ZONE” CRUMB CATCHER BASKET ASSEMBLY 1 2 24429 . HANDLE...
Page 60 - FILTER PUMP ASSEMBLY
Model OFG- 390 3-15 106 Figure & Item No. Part No. Description Qty. FILTER PUMP ASSEMBLY 64218 PUMP SUBASSY 8GPM √√√√√ 1 23468 ROTOR - 8 GPM PUMP .......................................... 1 √√√√√ 2 23647 BODY - 8 GPM PUMP ............................................ 1 √√√√√ 3 17456 PUMP SHIELD ...
Page 62 - GAS BURNER ASSEMBLY
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-10 GAS BURNER ASSEMBLY 0* 56990-01 BURNER ASSY – NATURAL ....................................................... 2 0* 56990-02 BURNER ASSY – LP ..................................................................... 2 0* 56990-03 BURNER ...
Page 64 - GAS PIPING AND CONTROLS
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-11 GAS PIPING AND CONTROLS 1 FP01-117 ELBOW ......................................................................................... 2 2 FP05-010 FITTING 3/8 TUBE TO 1/4 NP ...................................................... 2 3 65...
Page 65 - BURNER TUBES
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-12 BURNER TUBES 1 54480 BRACKET ASSY – HIGH LIMIT SENSING BULB ........................ 3 2 62051 CLIP – SPREADER – HEAT TUBE ............................................... 6 3 53670 SPACER – HIGH LIMIT ..................................
Page 66 - CARRIER AND RACKS
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-13 CARRIER AND RACKS 1 62183 CARRIER ASSY .......................................................... 1 2 44782 RACK HALF SIZE – 8 HEAD FRYER ........................ 5 2 62181* 390 BASKET (OPTIONAL) .......................................
Page 67 - VACUUM SWITCH
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-14 VACUUM SWITCH 1 60202 TUBE-VACUUM SWITCH ............................................... 1 √√√√√ 2 14240 KIT - VACUUM SWITCH - VERITCAL ......................... 1 √√√√√ 2 55607 VACUUM SWITCH – VERTICAL ................................
Page 69 - FLUE ASSEMBLY AND BLOWER
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-15 FLUE ASSEMBLY AND BLOWER (SN: BT0802002 & BELOW) 1 55681 FLUE ASSY – WELDMENT ............................................. 1 2 55783 BRACKET – FLUE RETAINING ..................................... 1 3 SC03-005 SCREW SD #8 X 1/2 ...
Page 73 - FRYPOT AND DRAIN PIPING
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-16 FRYPOT AND DRAIN PIPING √√√√√ 4 14330 PROBE ASSY – DOMESTIC ......................................................... 1 √√√√√ 4 14266 KIT-CE PROBE CONNECTOR RETROFIT (probe not included) .. 1 (CE units built prior to NOV. 1, 1999) 5...
Page 75 - LIFT BEAM AND SHROUDS
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-17 LIFT BEAM AND SHROUDS (SN: BT0802002 & BELOW) 1 55678 ASSY – I-BEAM/LIFT FRAME .................................................... 1 2 51548 . LIFT I-BEAM ...........................................................................
Page 76 - Figure 3-18. Counterweight and Pulley System
Model OFG- 390 3-31 1209 Figure 3-18. Counterweight and Pulley System SN: BT0802002 & BELOW
Page 77 - COUNTERWEIGHT AND PULLEY SYSTEM
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-18 COUNTERWEIGHT AND PULLEY SYSTEM (SN: BT0802002 & BELOW) 1 52475 PULLEY ASSY ............................................................................... 1 2 51677 . PULLEY PLATE ..................................................
Page 78 - COUNTERWEIGHT SYSTEM
Model OFG- 390 3-33 1209 Figure & Item No. Part No. Description Qty. 3-21 COUNTERWEIGHT SYSTEM (SN: BT0802003 & ABOVE) 1 35026 ARM, LID SUPPORT ..................................................... 2 √√√√√ 2 35207 CABLE ...........................................................................
Page 80 - FAST READY PARTS
Model OFG- 390 Figure & Item No. Part No. Description Qty. 3-19 FAST READY PARTS 1 66287 ASSY - 392/692 - 120V FAST HEADER .................. 1 1 66288 ASSY - 392/692 - 230V FAST HEADER - CE ......... 1 1 66385 ASSY - 392/692 - 220-240V FAST HEADER .......... 1 1 66241 STUD ASSY - 392/692 CONTRO...
