Heat & Glo AT-ZC - Manual
Heat & Glo AT-ZC – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – SAFETY AND WARNING INFORMATION
- Page 3 – ii; Section 5: Replacement Parts; Table of
- Page 4 – Appliance Certification; Installers; CERTIFICATION; Installation Codes; Approvals
- Page 5 – Preparation
- Page 6 – VENTING AND INSTALLATION; ANSI Z223 and these instructions.
- Page 7 – The vent system configuration to be used.; HEIGHT
- Page 9 – Connecting the Vent Pipe
- Page 13 – The Gas Control; The gas control systems used with this model is; Securing the
- Page 15 – DISCONNECT REMOTE CONTROLS IF YOU ARE; For Standing Pilot Ignition Wiring
- Page 16 – CAUTION; LABEL ALL WIRES PRIOR TO DISCONNECTION
- Page 17 – Figure 9. Fan Wiring Diagram; Installing Logs
- Page 18 – Figure 10. Glass Assembly
- Page 22 – IMPORTANT; TURN OFF THE GAS BEFORE SERVICING
- Page 23 – Figure 14. Burner Flame Patterns
- Page 24 – Replacement; All parts listed in this; INSTALLERS GUIDE; may be; Standing Pilot Only
- Page 25 – Standing Pilot Continued
- Page 26 – Accessories; PAR T; Logs C omplete Set
Heat-N-Glo Fireplace
Model:
AT-ZC
Patents Pending
Installers Guide
WARNING: IMPROPER
INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR
MAINTENANCE CAN CAUSE
INJURY OR PROPERTY DAMAGE.
REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL
INFORMATION CONSULT A
QUALIFIED INSTALLER, SERVICE
AGENCY, OR THE GAS SUPPLIER.
Underwriters Laboratories Listed
485-980-A 1/98
READ THIS MANUAL BEFORE
INSTALLING OR OPERATING THIS
APPLIANCE. THIS
INSTALLERS GUIDE
MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.
1.
This appliance may be installed in an
aftermarket, permanently located,
manufactured (mobile) home, where
not prohibited by local codes.
2. This appliance is only for use with the
type of gas indicated on the rating
plate. This appliance is not convertible
for use with other gases, unless a
certified kit is used.
Please contact your Heat-N-Glo Fireplace dealer for any
questions or concerns. For the number of your nearest
Heat-N-Glo dealer, please call 612-890-8367.
Printed in U.S.A.
Copyright 1998,
Heat-N-Glo Fireplace Products, Inc.
6665 West Highway 13, Savage, MN 55378
- Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
-
What to do if you smell gas
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use any phone in your building.
Immediately call your gas supplier
from a neighbor's phone. Follow the gas
supplier's instructions.
If you cannot reach your gas supplier,
call the fire department.
- Installation and service must be
performed by a qualified installer,
service agency, or the gas supplier.
WA R N I N G
IF THE INFORMATION IN
THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE
OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
i SAFETY AND WARNING INFORMATION READ and UNDERSTAND all instructions carefully before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Firepla...
ii Safety and Warning Information .................... i Section 1: Approvals and Codes ................ 1 Approval Listings and Codes .................................. 1Appliance Certification ............................................ 1Installation Codes ...........................................
1 Approval Listings and Codes Appliance Certification The Heat-N-Glo models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. CERTIFICATION MODEL LABORATORY TYPE STANDARD AT-ZC Underwriters Direct Vent ANSI Z21.44CGA2.19/IR#41 ...
