Heat & Glo 8000TRD - Manual
Heat & Glo 8000TRD – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Installers Guide; DO NOT; Owners Guide; ALERTED; SAFETY AND WARNING INFORMATION
- Page 3 – TABLE OF CONTENTS
- Page 4 – Log Set Assembly; Service Parts
- Page 5 – Service Parts List / Liste des pièces de rechange; COMMON PARTS / PIÉCES COMMUNES
- Page 6 – Appliance Certification; The Heat-N-Glo fireplace models discussed in this; Certification; Underwriters Laboratories; Installation Codes
- Page 7 – Getting Started; Introducing the Heat-N-Glo Gas Fireplaces; Pre-install Preparation; Do not install any
- Page 9 – Installing the Fireplace; Step 1. Locating the Fireplace; Vertical Sections; Constructing the Fireplace Chase; TREATMENT OF FIRESTOP SPACERS AND
- Page 10 – Framing Dimensions; Step 2. Framing the Fireplace; MEASURE FIREPLACE DIMENSIONS AND
- Page 12 – Step 3. Installing the Vent System
- Page 13 – Figure 6. Straight Up Vertical Venting; STRAIGHT UP; VERTICAL VENTING; Flue Restrictor Instructions; Figure 8. Flue Restrictor; BREAK; Figure 7; On vertical venting configurations you may want to
- Page 14 – HORIZONTAL VENTING; Figure 10. Corner Installation; Match the amount of vertical you have in the sys-; Figure 9; . Center the Flue Restrictor on vent and secure in
- Page 15 – On vertical venting configurations where; Figure 11. Venting with One 90° Elbow; elbow is first attached to the unit,
- Page 16 – ELBOWS
- Page 17 – Figure 15. Venting with Two 90° Elbows
- Page 18 – Figure 16. Venting with three 90° elbows; V H H + H
- Page 19 – Figure 17. Venting with three 90° elbows
- Page 20 – B. Installing Vent Components; Venting Out Rear
- Page 24 – = AREA WHERE TERMINAL IS NOT PERMITTED; Figure 32. Vent Termination Minimum Clearances; public; J or K; 0” minimum for vinyl clad soffits.; NOT
- Page 26 – Step 5. The Gas Control Systems; Standing Pilot Ignition; Standing Pilot Ignition System; IPI IGNITION
- Page 27 – Figure 36. Gas Supply Line; Step 6. The Gas Supply Line; Pressure
- Page 28 – Step 8. Wiring the Fireplace; This appliance
- Page 29 – Ignition module, valve, pilot and wall switch operate on 3 volts.; Optional Accessories
- Page 30 – require; Figure 41. Sealant Material
- Page 32 – Step 11. Before Lighting the Fireplace; Step 12. Lighting the Fireplace
- Page 33 – Maintaining and Servicing Your Fireplace; Fireplace Maintenance; Placing Ember
1
- Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
-
What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
- Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
Installers Guide
W A R N I N G : I M P R O P E R I N S TALLA-
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL INFOR-
MATION CONSULT A QUALIFIED IN-
STALLER, SERVICE AGENCY, OR THE
GAS SUPPLIER.
Underwriters
Laboratories Listed
380-900J 3/03
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS
INSTALLERS
GUIDE
MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.
1. This appliance may be installed in an af-
termarket, permanently located, manufac-
tured (mobile) home, where not prohibited
by local codes.
2. This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
Please contact your Heat-N-Glo dealer for any questions
or concerns. For the number of your nearest Heat-N-
Glo dealer, please call 1-888-427-3973.
Printed in U.S.A. Copyright 2003,
Heat-N-Glo, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
WARNING: IF THE INFORMATION
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
SONAL INJURY, OR DEATH.
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.
Model:
8000TRD
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 These units MUST use one of the vent systems described in the Installing the Fireplace section ofthe Installers Guide . NO OTHER vent systems or components MAY BE USED . This gas fireplace and vent assembly MUST be vented directly to the outside and MUST NEVER be attached to a chimney serving a se...
3 TABLE OF CONTENTS Safety and Warning Information ............................................... 2 Service Parts Lists .................................................................... 4 Section 1: Approvals and Codes .............................................. 6 Appliance Certification .......
4 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. 1 0 11 1 2 1 3 1 4 1 6 1 5 1 8 1 7 2 3 4 5 6 7 8 1 9 Log Set Assembly (NG, LP) Exploded Parts Diagram(GN, PL) Vue éclatée des pièces Service Parts 8000TRD 8000TRD Beginning Manufacturing Date: 6-01 ...
