Heat & Glo 6000 GDVFL - Manual

Heat & Glo 6000 GDVFL

Heat & Glo 6000 GDVFL – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
Page: / 40

Table of Contents:

  • Page 2 – SAFETY AND WARNING INFORMATION; ALERTED
  • Page 3 – ii; Table of; Section 5: Replacement Parts
  • Page 4 – Appliance Certification; CERTIFICATION; and; Installation Codes; Approvals
  • Page 5 – Preparation; Installers; Getting
  • Page 6 – Figure 1. Diagram of the6000 Series
  • Page 7 – Clearance Requirements
  • Page 8 – CAUTION; MEASURE FIREPLACE DIMENSIONS, AND; NOTE: DIMENSIONS SHOWN IN INCHES
  • Page 9 – A. Vent System Approvals; NO OTHER VENTING SYSTEMS OR; Identifying Vent Components
  • Page 11 – Figure 6. Corner Installation; approved to use 45° elbows in corner installations.; HORIZONTAL VENTING
  • Page 12 – Figure 7. Venting with One 90° Elbow
  • Page 13 – ELBOWS; Figure 8. Venting with Two 90° Elbows
  • Page 14 – Figure 9. Venting with three 90° elbows
  • Page 15 – B. Installing Vent Components
  • Page 17 – REQUIRED; NOTE; Model DVK-01TRD does not need an exterior
  • Page 22 – =AREA WHERE TERMINAL IS NOT PERMITTED; Figure 19. Vent Termination Minimum Clearances; IF EXTERIOR WALLS ARE FINISHED WITH
  • Page 23 – N O T E; This also pertains to vertical vent systems installed
  • Page 25 – Standing Pilot Ignition; Securing the
  • Page 27 – Figure 23. Gas Supply Line; Gas Pressure; P r e s s u r e
  • Page 28 – For Standing Pilot Ignition Wiring; This appliance; LABEL ALL WIRES PRIOR TO DISCONNECTION
  • Page 29 – Figure 25. Fan Wiring Diagram; Electrical wiring must be installed by a licensed
  • Page 30 – Finishing
  • Page 31 – Hearth Extensions; Ember Material
  • Page 33 – Figure 29. Glass Assembly; HAND TIGHTEN THE WING NUTS, BUT BE; Figure 30. Placement of the Ember Material; IT IS STRONGLY RECOMMENDED THAT TRIM
  • Page 35 – IMPORTANT; TURN OFF THE GAS BEFORE SERVICING
  • Page 36 – Figure 31. Burner Flame Patterns
  • Page 37 – All parts listed in this; INSTALLERS GUIDE; may be; Standing Pilot Only
  • Page 38 – DSI Ignition Only
  • Page 39 – Both Standing Pilot and DSI Ignition; GLASS SPECIFICATIONS: 6000GDVFL: 20” X 34”
  • Page 40 – A c c e s s o r i e s
Loading the manual

WARNING

IF THE INFORMATION IN

THESE INSTRUCTIONS IS

NOT FOLLOWED EXACTLY, A

FIRE OR EXPLOSION MAY

RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY,

OR LOSS OF LIFE.

- Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of this

or any other appliance.

-

What to do if you smell gas

• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the

fire department.

- Installation and service must be performed by a

qualified installer, service agency, or the gas

supplier.

Heat-N-Glo Fireplace

Models:

6000 GDVFL

6000 XLS

U.S. Patents 4,793,322; 4,875,464; 5,000,162 and Patents Pending
Canadian Patent 1,297,746

Installers Guide

WARNING: IMPROPER

INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR

MAINTENANCE CAN CAUSE

INJURY OR PROPERTY DAMAGE.

REFER TO THIS MANUAL. FOR

ASSISTANCE OR ADDITIONAL

INFORMATION CONSULT A

QUALIFIED INSTALLER, SERVICE

AGENGY, OR THE GAS SUPPLIER.

A.G.A. Design Certified/CGA Certified and

Underwriters Laboratories Listed. See

Approvals Tabel on Page 1.

446-982-A 8/97

READ THIS MANUAL BEFORE INSTALLING
OR OPERATING THIS APPLIANCE. THIS

INSTALLERS GUIDE

MUST BE LEFT WITH

APPLIANCE FOR FUTURE REFERENCE.

1.

This appliance may be installed in an

aftermarket, permanently located,

manufactured (mobile) home, where

not prohibited by local codes.

2. This appliance is only for use with the

type of gas indicated on the rating

plate. This appliance is not convertible

for use with other gases, unless a

certified kit is used.

Please contact your Heat-N-Glo Fireplace

dealer for any questions or concerns. For the

number of your nearest Heat-N-Glo dealer,

please call 612-890-8367.

Printed in U.S.A.
Copyright 1997,

Heat-N-Glo Fireplace Products, Inc.

6665 West Highway 13, Savage, MN 55378

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - SAFETY AND WARNING INFORMATION; ALERTED

i SAFETY AND WARNING INFORMATION READ and UNDERSTAND all instructions carefully before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Firepla...

Page 3 - ii; Table of; Section 5: Replacement Parts

ii Table of Contents Safety and Warning Information ...................... i Section 1: Approvals and Codes ..................... 1 Approval Listings and Codes ................................ 1 Appliance Certification ...................................... 1 Installation Codes ........................

Page 4 - Appliance Certification; CERTIFICATION; and; Installation Codes; Approvals

1 Approval Listings and Codes Appliance Certification The Heat-N-Glo fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. CERTIFICATION MODEL LABORATORY TYPE STANDARD 6000GDVFL A.G.A./CGA Direct Vent ANSI Z21.50•CG...

Other Heat & Glo Models

All Heat & Glo Other