Grizzly Industrial T10252 - Manual
Grizzly Industrial T10252 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Figure 4; The two inner screws of the four-screw; Installation; Tools Needed; Go to Grizzly.com or call Customer Service; To install the dust port onto the sander:
- Page 3 – Figure 7; It may be necessary to gently tap on; Lower
- Page 4 – Figure 5
MODEL T10252
DUST PORT
FOR G1183/G1276
INSTRUCTIONS
If you need help with your dust port, call our Tech
Support at: (570) 546-9663.
Copyright © NoVEMBEr, 2010 By grizzly iNdustrial, iNC.
WaRNING: NO PORTION OF ThIS MaNUaL May bE REPRODUCED IN aNy ShaPE
OR FORM WIThOUT ThE WRITTEN aPPROvaL OF GRIzzLy INDUSTRIaL, INC.
#ts13350 priNtEd iN taiWaN
Introduction
the Model t10252 dust port helps capture
dust from the disc sander on the g1183/g1276
Combination sanders that were manufactured
before august, 2010.
Recommended CFM at Dust Port: 150 CFM
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust col-
lector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to cal-
culate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.
Dust Collection
the included dust collection hose assembly has a
2
1
⁄
2
" adapter for connection to your dust collection
system.
DO NOT operate the Model G1183/G1276
sander without an adequate dust collec-
tion system. This sander creates substan-
tial amounts of wood dust while operating.
Failure to use an adequate dust collection
system can result in short and long-term
respiratory illness.
NOTICE
The installation of the dust port requires
that you remove the lower disc guard from
the sander and modify it. Read through
this entire document before beginning the
installation procedure on the next page.
Shipping Inventory (Figure 1)
a.
dust Chute ................................................. 1
b.
phillips head screws #10-24 x
3
⁄
8
" ............. 2
C.
hose Clamps 1
1
⁄
2
" ...................................... 2
D.
dust hose 1
1
⁄
2
" x 10" .................................. 1
E.
hose adapter 2
1
⁄
2
" x 1
1
⁄
2
" ........................... 1
F.
Cover plate ................................................. 1
G.
Flat Washers
5
⁄
16
" ........................................ 2
h.
hex Bolts
5
⁄
16
-18" x 12" ............................... 2
Figure 1.
Model t10252 shipping inventory.
a
B
C
d
E
F
g
h
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2- t10252 dust port 3. With the help from another person to steady the sander, tip it back to gain access to the two cap screws underneath the base that secure the lower blade guard, then remove these cap screws (see Figure 4 ). 4. remove the eight phillips head screws behind the guard that secure ...
t10252 dust port -3- Figure 5. phillips head screws that secure and adjust the guard sections. phillips head screws (1 side shown) Figure 6. removing the upper disc guard. upper disc guard 5. Fully loosen the two set screws that secure the disc to the motor shaft, as shown in Figure 7 . 6. take care...
-4- t10252 dust port 13. Make sure the disc is fully seated on the motor shaft, then re-tighten both set screws to secure it. 14. re-install the upper disc guard with the eight phillips head screws that you removed in Step 4 . 15. thread the inner two screws from Step 10 in or out to adjust the uppe...
