Page 3 - Table of Contents
Model g0703 (Mfg. since 8/09) -3- Table of Contents iNTRODUCTiON ............................................................................................................................... 4 Manual Accuracy ............................................................................................
Page 4 - iNTRODUCTiON; Machine Description; Contact info
-4- Model g0703 (Mfg. since 8/09) iNTRODUCTiON the Model g0703 is a 2-stage cyclone dust col-lector designed to capture the dust from wood-working machines. the pleated cartridge filter provides a large sur-face area and crank-operated internal paddles knock loose caked-on dust to maintain filter ef...
Page 5 - identification
Model g0703 (Mfg. since 8/09) -5- figure 1. identification. identification To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations. Motor Blower housing inlet remote Magnetic Switch Canister Filter Cyclone Funnel Collection...
Page 6 - Machine Data Sheet
-6- Model g0703 (Mfg. since 8/09) model G0703 1-1/2 HP CyClone dust ColleCtor Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 mACHIne dAtA sHeet Product Dimensions: Weight ........................................................................................
Page 8 - NOTICE; Safety Instructions for Machinery
-8- Model g0703 (Mfg. since 8/09) Safety instructions for Machinery 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing loss. 5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry that can catch in moving parts. Wea...
Page 11 - SECTiON 2: CiRCUiT REQUiREMENTS; full Load amperage Draw
Model g0703 (Mfg. since 8/09) -11- Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual. 110/220v Operation SECTiON 2: CiRCUiT REQUiREMENTS full Load amperage Draw ...
Page 12 - items Needed for
-12- Model g0703 (Mfg. since 8/09) SECTiON 3: SETUP the following items are needed to complete the setup process, but are not included with your machine: Description Qty • Assistants ................................................... 1 • Safety glasses .................. For Each person • Wrench 1 ...
Page 13 - inventory
Model g0703 (Mfg. since 8/09) -13- inventory After all the parts have been removed from the boxes, you should have the following items: Machine inventory (figure 3): Qty a. dust Collector & Filter Assembly ................ 1 b. Control Box Assembly ................................ 1 figure 3. Ma...
Page 14 - Site Considerations; Weight Load; Space Allocation
-14- Model g0703 (Mfg. since 8/09) Site Considerations figure 6. Minimum working clearances. Weight Load Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be i...
Page 15 - assembly
Model g0703 (Mfg. since 8/09) -15- assembly To assemble your dust collector, do these steps: 1. invert the stand, place one 3 ⁄ 8 " lock washer on four caster wheel studs, and thread each caster stud into the stand ( figure 7 ). 2. Using a 3 ⁄ 8 " wrench, tighten each caster stud. figure 10....
Page 19 - Test Run
Model g0703 (Mfg. since 8/09) -19- 5. press the on/oFF button to turn the machine ON . Make sure your hand stays poised over the switch in case you need to quickly turn the machine OFF . 6. listen to and watch for abnormal noises or actions. the machine should run smoothly with little or no vibratio...
Page 20 - SECTiON 4: COLLECTiON SYSTEM; Tips for Optimum Performance; System Setup; Metal Duct
-20- Model g0703 (Mfg. since 8/09) SECTiON 4: COLLECTiON SYSTEM the Model g0703 is designed to collect dust from one machine at a time. this can be accomplished by either connecting it to one machine at a time or by connecting it to multiple machines and using blast gates to control which branch is ...
Page 21 - flexible Duct; Plastic Duct
Model g0703 (Mfg. since 8/09) -21- there are a number of options when it comes to metal duct, but metal duct that is specially manu-factured for dust collection is the best choice. When selecting your metal duct, choose high quality metal duct with smooth welded internal seams that will minimize air...
Page 23 - SECTiON 5: OPERaTiONS; General Operation
Model g0703 (Mfg. since 8/09) -23- SECTiON 5: OPERaTiONS Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. always wear safety glasses, a respirator, and hearing protection when operating this machine. Loose hair and cloth- ing could get caught ...
Page 25 - SECTiON 6: aCCESSORiES
Model g0703 (Mfg. since 8/09) -25- SECTiON 6: aCCESSORiES ACCESSoriES P0703088—220v Mag Switch installing this mag switch will allow you to run the g0703 on 220V single-phase power. to convert the dust collector to 220V, just remove the 110V switch, install this one in its place, and rewire the moto...
Page 27 - SECTiON 7: MaiNTENaNCE; Schedule
Model g0703 (Mfg. since 8/09) -27- SECTiON 7: MaiNTENaNCE always disconnect power to the machine before performing maintenance. failure to do this may result in serious person- al injury. For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructio...
Page 28 - Troubleshooting
-28- Model g0703 (Mfg. since 8/09) review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical Support at (570) 546-9663. SECTiON 8: SERviCE...
Page 29 - Dust Collector Operation
Model g0703 (Mfg. since 8/09) -29- Symptom possible Cause possible Solution loud, repetitious noise, or excessive vibration coming from dust collector. 1. dust collector is not on a flat surface and wobbles. 2. impeller is damaged and unbalanced. 3. the motor mounting or housing connections are loos...
Page 30 - Wiring Safety instructions
-30- Model g0703 (Mfg. since 8/09) these pages are current at the time of printing. however, in the spirit of improvement, we may make chang-es to the electrical systems of future machines. Study this section carefully. if there are differences between your machine and what is shown in this section,...
Page 31 - MAGNETIC
Model g0709 (Mfg. since 8/09) -31- READ ELECTRICAL SAFETY ON PAGE 30! MOTOR 110V Hot Neutral Ground A1 A2 98 2T1 6T3 97 4T2 2T1 6T3 4T2 1L1 5L3 13NO 14NO 3L2 96 95 NHD C-09D 110V NHD NTH-21 18 19 20 21 17 O R MAGNETIC SWITCH ASSY CIRCUIT BOARD 110V ON/OFFSWITCH AC OUT OL_NO AC IN A2 1 2 3 4 Run Capa...
Page 32 - MOTOR
-32- Model g0703 (Mfg. since 8/09) READ ELECTRICAL SAFETY ON PAGE 30! MOTOR Hot Hot Ground 6-15 Plug (Rewired 220V) 220 VAC G Bl Wt Gn A1 A2 98 2T1 6T3 97 4T2 2T1 6T3 4T2 1L1 5L3 13NO 14NO 3L2 96 95 NHD C-09D 220V NHD NTH-11 9 10 11 8 O R MAGNETIC SWITCH ASSY CIRCUIT BOARD 220V ON/OFFSWITCH AC OUT O...
Page 33 - Electrical Component Locations
Model g0709 (Mfg. since 8/09) -33- READ ELECTRICAL SAFETY ON PAGE 30! Electrical Component Locations Magnetic Switch and Circuit Board location Motor Junction Box location figure 39. Electrical component locations.
Page 34 - Main
-34- Model g0703 (Mfg. since 8/09) 1-1 1-2 1-3 1-4 1-5 220V Conversion Kit 88-1 88-2 88-3 75-1 75-2 75-3 75-4 75-5 1 2 3 4 5 6 7 8 9 10 10-1 11 12 13 13-1 14 15 16 16-1 17 18 19 20 21 22 22-1 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 38-1 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 5...
Page 35 - Main Parts List
Model g0703 (Mfg. since 8/09) -35- Main Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0703001 MOTOR 1-1/2 HP 110/220V 1PH 49 PR83M EXT RETAINING RING 20MM 1-1 P0703001-1 MOTOR FAN COVER 50 P0703050 PADDLE SHAFT CAP 1-2 P0703001-2 MOTOR FAN 51 P0703051 SEAL 1-3 P0703001-3 MOTOR JUNCTION...
Page 36 - Machine Labels
-36- Model g0703 (Mfg. since 8/09) Machine Labels Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. if any label is removed or becomes unreadable, REPLaCE that label before ...
Page 37 - WARRANTY CARD
C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...
Page 39 - WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Griz...
Page 40 - Buy Direct and Save with Grizzly; ORDER
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ ORDER 24 HOURS A DAY! 1-800-523-4777 Visit Our Website Today For Current Specials!
