Grizzly Industrial T10125 - Manual
Grizzly Industrial T10125 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – step 8; installation; figure 3
- Page 3 – figure 7; figure 6
- Page 4 – installing or adjusting a carbide cutter:; insert service
- Page 5 – accessories; h7319—10 pack of indexable carbide inserts; figure
- Page 7 – Warranty and returns
- Page 8 – n4RUSTED0ROVENANDA'REAT6ALUE
The Model T10125 spiral cutterhead is designed
to replace the straight knife cutterhead on the
Model G0452 6" jointer.
The total procedure of changing the cutterheads
and setting up the jointer takes approximately
one hour. The job consists of removing the old
cutterhead, installing and shimming the new spi-
ral cutterhead, and readjusting the outfeed table
even with the carbide inserts at TDC (top dead
center). Call Technical Support at (570) 546-9663
if you need help.
CopyriGhT © july, 2008 By Grizzly inDusTrial, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#Bl10874 prinTeD in China
inventory
(
figure 2
)
a.
spiral Cutterhead ....................................... 1
b.
Torx Drivers T20 ........................................ 2
c.
Flat head Torx screws T20 M6-1 x 15 ...... 3
d.
indexable Carbide inserts 14 x 14 x 2 ....... 5
e.
Torx l-Wrenches T20 (not shown) ............ 2
figure 1.
precision straightedges.
model t10125
6" spiral cutterhead
instructions
figure 2.
spiral cutterhead inventory.
C
D
B
a
the t10125 spiral cutterhead is only designed
to be used with the grizzly model g0452 6"
Jointer. do not install this cutterhead in
any other jointer model or make. doing so
could result in property damage or serious
personal injury.
recommended tools
Wrench 17mm.................................................... 1
precision straightedge (
figure 1
) ..................... 1
Feeler Gauge set .............................................. 1
pair of heavy leather Gloves ........................... 1
g9644—12" precision straightedge
h2675—16" precision straightedge
is your straightedge really straight? These grade
00 heavy-duty stainless steel straightedges are
manufactured to Din874 standards for profes-
sional results in set-up and inspection work.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2- T10125 6" spiral Cutterhead figure 3. example of jointer disassembly steps 1– 4 . figure 4. example of removing nut and lock washer on bearing block stud. figure 5. example of cutterhead removed. 5. remove the nut and lock washer on the bear- ing block stud, as shown in figure 4 , and repeat...
-3- T10125 6" spiral Cutterhead 13. Tighten the spiral cutterhead in place, and ensure both pulley setscrews are tight. 14. using the straightedge and feeler gauge set, inspect the cutterhead parallelism with the outfeed table as shown in figure 7 . With the straightedge in position, raise or lo...
-4- T10125 6" spiral Cutterhead When correctly set, the carbide insert will just touch the straightedge when the insert is at its highest point of rotation ( figure 10 ) . figure 10. using a straightedge to align outfeed table height with insert at TDC. HigV^\]iZY\Z Dji[ZZY >c[ZZY —if your ou...
