Grizzly Industrial H8110 - Manual
Grizzly Industrial H8110 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Using a 5mm hex wrench, thread the bolts; not fully tighten at this time.; figure 15. Upper cross panel installation.; ously installed cross braces.; position the left side leg (B) on the floor so; Carefully engage the slots in the left leg with
- Page 3 – until they are fully seated in the grooves.; Rotate
- Page 4 – parts Breakdown and Inventory; parts; FLat Washer 8mm
MODEL H8110
9 DRAWER EURO STYLE
WORKBENCH-BIRCH
INSTRUCTIONS
Copyright © JULy 2009 By grizzLy indUstriaL, inC.
WARNINg: NO pORTION Of THIS MANUAL MAY BE REpRODUCED IN ANY SHApE
OR fORM WITHOUT THE WRITTEN AppROvAL Of gRIzzLY INDUSTRIAL, INC.
(For modeLs manUFaCtUred sinCe 7/09) #Cr12018 printed in China
figure 11. model h8110 Birch Workbench.
Safety & Limitations
•
maximum workbench table load is 500 lbs.
•
do not stand or climb on the workbench.
•
do not apply an unbalanced load on the table
that could result in the workbench tipping.
•
Keep unsupervised children away from the
workbench.
•
do not stand or climb on the workbench.
•
do not use workbench outdoors or in wet or
damp locations.
•
do not overload the vises or use cheater
pipes on the vise handles to increase lever-
age.
•
do not weld on this bench.
Specifications
Finish .......................................... Lacquer sealed
drawer slides ................................... Ball Bearing
number of drawers ........................................... 9
Front Vise size ..................................... 19
3
⁄
4
" x 7"
end Vise size ............................................6" x 6"
overall size .............. 84
1
⁄
2
"W x 24
11
⁄
16
"d x 34
1
⁄
4
"h
drawer size ..................... 15
3
⁄
8
"W x 13
7
⁄
8
"d x 4"h
storage shelf size .....................55
1
⁄
2
"W x 18
1
⁄
2
"d
shipping Weight ......................................367 lbs.
Assembly
refer to the last page of these instructions to
inventory your shipment for ease of assembly.
To assemble the workbench:
1. position the right side leg (C) on the floor
so the Up arrow is pointing upward and the
Front arrow points to the front, as shown in
figure 12.
2. place the two lower cross braces (e) on the
floor so the slots face each other, as shown
in
figure 12.
E
E
C
E2
E4
E3
figure 12. right leg and cross brace installation.
3. insert the barrel nuts (e4) (figure 12) into the
ends of the cross braces so the slotted end
faces outward and the screwdriver slots are
aligned horizontally with the direction of the
cross braces.
4. insert the cross braces into the mortised
holes into the right-side leg, as shown in
figure 12.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2- model h8110 (mfg. since 7/09) E C F E figure 13. Lower panel installation. 5. place a flat washer (e2) on each barrel bolt (e3), and insert the bolts through the right-side leg ( figure 12). 6. Using a 5mm hex wrench, thread the bolts into the barrel nuts (e4) ( figure 12), but do not fully tigh...
model h8110 (mfg. since 7/09) -3- 14. insert the bolts through the left-side leg, tighten with a 5mm hex wrench, and all other barrel bolts at this time. 15. align the pre-drilled holes in the underside of the work bench table top (a) with the pre-drilled holes in the legs. 16. place a flat washer (...
-4- model h8110 (mfg. since 7/09) parts Breakdown and Inventory parts fastener Kit part Numbers QTY ph8110001 handLe sCreW 18 pW01m FLat Washer 8mm 12 ph8110003 BarreL BoLt 3.5" 8 ph8110004 BarreL nUt 8 ph8110005 handLe 9 paW05m heX WrenCh 5mm 1 paW04m heX WrenCh 4mm 1 ph8110008 Wood sCreW 2"...
