Page 3 - Table of Contents
Table of Contents INTRODUCTION ............................................................................................................................... 2 Foreword .....................................................................................................................................
Page 4 - Foreword; INTRODUCTION; Contact Info
-2- G9749 Variable Speed Drill Press If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C / O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 E-Mail: [email protected] We stand behind our machines. If you have a...
Page 5 - MACHINE DATA
G9749 Variable Speed Drill Press -3- The information contained herein is deemed accurate as of 3/18/2007 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G9749 MAC...
Page 7 - Identification
G9749 Variable Speed Drill Press -5- Figure 1. Right side controls. Identification Figure 2. Left side controls. Refer to the list below and see Figures 1 & 2 to become familiar with the drill press controls. A. Speed Selector Control: Allows variable speeds from 300 to 2000 RPM. B. Depth Gauge:...
Page 9 - Safety Instructions for Machinery
G9749 Variable Speed Drill Press -7- ��� ����� ������ �������� ���� ����� ����� ����������� ���������� ��� �������� ���������� � ����� ������ ���������� ������������� ���� ����� ���� �������� ����������� ��� ��������������������������������� ����� ���� ��������� ���� ��������� �� ����� ���� ��������...
Page 10 - Additional Safety for Drill Presses
-8- G9749 Variable Speed Drill Press 1. EYE/FACE/HAND PROTECTION. A face shield used with safety glasses is rec-ommended. Always keep hands and fin-gers away from the drill bit. Never hold a workpiece by hand while drilling! DO NOT wear gloves when operating the drill. 2. SECURING BIT. Properly tigh...
Page 11 - SECTION 2: CIRCUIT REQUIREMENTS; NOTICE
G9749 Variable Speed Drill Press -9- Serious personal injury could occur if you connect the machine to the power source before you have completed the setup pro- cess. DO NOT connect the machine to the power source until instructed to do so. 110/220V Operation SECTION 2: CIRCUIT REQUIREMENTS Amperage...
Page 12 - Extension Cords
-10- G9749 Variable Speed Drill Press In the event of an electrical short, grounding reduces the risk of electric shock. The grounding wire in the power cord must be properly connected to the grounding prong on the plug; likewise, the outlet must be properly installed and grounded. All electrical co...
Page 13 - Site Considerations
G9749 Variable Speed Drill Press -11- Wear safety glasses dur- ing the entire setup pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! Setup Safety SECTION 3:...
Page 14 - Unpacking and
-12- G9749 Variable Speed Drill Press The Model G9749 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing materials for p...
Page 15 - Mounting to Shop
G9749 Variable Speed Drill Press -13- The Model G9749 should be mounted to the floor. Because floor materials may vary, floor mounting hardware is not included. It is also necessary to level your machine with a precision level. Bolting to Concrete Floors Lag shield anchors with lag bolts (see Figure...
Page 16 - Inventory; Clean Up
-14- G9749 Variable Speed Drill Press Inventory After all the parts have been removed from the crate and boxes, you should have the following items: Contents (Figure 9) Qty A . Drill Press (not shown) ............................... 1 B. JT#6 Keyed Chuck ..................................... 1 C. Ch...
Page 17 - Assembly
G9749 Variable Speed Drill Press -15- Assembly Components and Hardware Needed: Qty Hex Wrench 5mm (provided) ............................ 1Rapid Downfeed Handle Shafts ........................ 3Rapid Downfeed Handle Knobs ........................ 3Table Crank Knob ......................................
Page 18 - Test Run and
-16- G9749 Variable Speed Drill Press Test Run and Spindle Break-In Once assembly is complete, test run your machine to make sure it runs properly. To test run the machine: 1. Make sure you have read and understood all of the safety instructions starting on Page 6 of this manual, and verify the mach...
Page 19 - SECTION 4: OPERATIONS; Installing Drill Chuck
G9749 Variable Speed Drill Press -17- SECTION 4: OPERATIONS NOTICE If you have never used this type of machine or equipment before, WE STRONGLY REC- OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Gri...
Page 20 - Changing Speeds
-18- G9749 Variable Speed Drill Press Installing /Removing Drill Bits Any drill bit you install in the chuck must be tight enough that it will not come loose during opera-tion. To install a drill bit into the chuck: 1. UNPLUG THE DRILL PRESS! 2. Open the chuck jaws wide enough to accept the drill bi...
Page 21 - Choosing Speeds
G9749 Variable Speed Drill Press -19- Choosing Speeds Twist/Brad Point Drill Bits Soft Wood Hard Wood Plastic Brass Aluminum Mild Steel 1/16" – 3/16" 3000 2500 2500 2500 3000 2500 13/64" – 3/8" 2000 1500 2000 1250 2500 1250 25/64" – 5/8" 1500 750 1500 750 1500 600 11/16" ...
Page 24 - Table Adjustments; Headstock Rotation
-22- G9749 Variable Speed Drill Press 2. Unlock the table by rotating the lock lever clockwise. 3. The table can now be adjusted: — Vertically by using the table crank handle (see Figure 19 ). — Horizontally by manually rotating the assembly around the center column. 4. When you have the table in th...
Page 27 - SECTION 5: ACCESSORIES
G9749 Variable Speed Drill Press -25- SECTION 5: ACCESSORIES G2500—20-PC Regular Sanding Drum Set This kit consists of 5 drums in popular 1 ⁄ 2 " x 1 ⁄ 2 ", 3 ⁄ 4 " x 1", 1"x 1", 1 1 ⁄ 2 " x 1 1 ⁄ 2 ", and 2" x 1 1 ⁄ 2 " sizes. Comes with 50, 80 and 120 grit s...
Page 28 - SECTION 6: MAINTENANCE; Unpainted Cast Iron
-26- G9749 Variable Speed Drill Press SECTION 6: MAINTENANCE Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. Protect the unpainted cast iron surfaces on the table by removing vises and fixtures daily and by wiping the ...
Page 29 - About Service; Troubleshooting
G9749 Variable Speed Drill Press -27- This section is provided for your convenience—it is not a substitute for the Grizzly Service Department. If you need help troubleshooting, need replacement parts, or are unsure how to perform the procedures in this section, then feel free to call our Technical S...
Page 31 - Electrical Components
G9749 Variable Speed Drill Press -29- Electrical Components Figure 30. G9749 switch wiring. Figure 32. G9749 motor capacitors. Figure 31. G9749 motor wiring (220V). 6 4 1 2 5 3
Page 33 - Headstock Parts Breakdown
G9749 Variable Speed Drill Press -31- Headstock Parts Breakdown � � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��� ��� �� �� �� �� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� � � �� �� ��� ��� ��� ��� ��� �� �� �� �� �� �� � ��� �� ��� �� �� �� �� �� �� �� �� �� ��� �� �� �� �� ��� � ��� ...
Page 34 - Headstock Components Parts Breakdown
-32- G9749 Variable Speed Drill Press Headstock Components Parts Breakdown � � � ��� � � � � ���� ���� ���� ���� ���� ���� �� ����� ����� ����� ����� ����� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� � � � � ���� ���� ���� ���� ���� ���� ���� �� � ����� ����� ����� ����� ����� ��� � Headstock Co...
Page 35 - Variable Speed Parts Breakdown
G9749 Variable Speed Drill Press -33- Variable Speed Parts Breakdown � ��� ��� ��� ��� ��� �� �� �� �� ��� �� �� �� �� �� �� �� �� �� �� ��� �� �� ��� ��� � VS Parts Page 32 Page 32
Page 36 - Base Parts Breakdown
-34- G9749 Variable Speed Drill Press Base Parts Breakdown ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ���
Page 37 - Parts List
G9749 Variable Speed Drill Press -35- Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P9749001 HEAD BODY 55-2 P9749055-2 START CAP 400MFD 125VAC 2 P9749002 SPINDLE COVER 55-3 P9749055-3 CAPACITOR COVER 3 P9749003 BEARING NUT 55-4 P9749055-4 MOTOR FAN 4 P6206 BALL BEARING 6206ZZ 55-5 P9749...
Page 39 - Label Placement
G9749 Variable Speed Drill Press -37- Label Placement Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label bef...
Page 40 - WARRANTY AND RETURNS
-38- G9749 Variable Speed Drill Press Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alteration...
