Graco 96A637 - Manual

6 310564 Setup WARNING To reduce the risk of serious injury whenever youare instructed to relieve pressure, always follow the Pressure Relief Procedure on page 10. Site Preparation Fig. 1. Relieve system pressure. For installing any one of the packages listed in this manual, select a sitewith at lea...

8 310564 Setup Connect the Fluid Lines Fig. 1. Connect system fluid supply line to the circula-tion package at fluid supply inlet (A). Close filter ballvalves (E) to isolate the circulation package from themain fluid supply line. Connect circulation package to the system fluid returnline at fluid re...

10 310564 Operation Pressure Relief Procedure WARNING PRESSURIZED EQUIPMENT HAZARD The system pressure must be manually relieved toprevent the system from starting or spraying acci-dentally. To reduce the risk of an injury from acci-dental spray from the gun, splashing fluid, ormoving parts, follow ...

12 310564 Operation Starting and Adjusting the Pump 1. Fig. 4. Open all fluid shutoff valves (5–two). Makesure Air Regulator (CC) is fully closed. 2. Open the spray gun at the last gun station andkeep it open while starting the pump. 3. Open the bleed-type master air valves (W, AA). 4. Slowly open a...

310564 13 Maintenance Preventive Maintenance Schedule The operating conditions of your particular systemdetermine how often maintenance is required. Estab-lish a preventive maintenance schedule by recordingwhen and what kind of maintenance is needed, andthen determine a regular schedule for checking...

14 310564 Maintenance Air Filter Service 1. Fig. 4. Every day, drain contaminants from thebowl before reaching the baffle level by openingthe drain at the bottom of the bowl (BB). WARNING To reduce the risk of serious injury whenever youare instructed to relieve pressure, always follow the Pressure ...

310564 15 Troubleshooting WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always followthe Pressure Relief Procedure (page 10). For pump service see pump manual. Problem Cause(s) Solution(s) Pump output low on both strokes Restricted air or hydraulic lin...

16 310564 Parts Right Hand Mount Model: 96A6374:1 Ratio, Glutton Pump TI0957 11 13 14 14 5 4,3 24 5,4,3 14 19 53,21,20 12,4,3 22 13 51 7 35 50 36 45 43 4,3,2 1 1516 17 23 3,4 14 Ref Ref 5 Detail A Detail A 51 Ref 50 Ref 49 48 47 46 Ref 43 Ref 37,38,39 42 35 10 46 31 52 25,26,27 32,33,34 30 44 54

26 310564 Technical Data 4:1 Ratio Glutton Pumps Category Data Maximum Fluid Working Pressure 2.4 MPa, 24.5 bar (350 psi) Air Operating Range 0.17–0.6 MPa, 1.7 – 6.2 bar (25 – 90 psi) Fluid Flow at 60 Cycles per Minute 21.2 liter/min (5.6 gpm) Cycles Per Liter (gallon) 2.7 (10.4) Maximum Recommended...

28 310564 Dimensions Mount the circulation package so the top of thebracket is 5 to 6 ft (1.5 to 1.8 m) above the floor. 1 Ensure that there is 5 ft (1.5 m) overhead clearance for wall mounted systems and at least 7 ft (2.1 m) forfloor mounted systems. 2 1 2 Model 96A637 Shown TI0957

310564 29 Mounting Hole Layout 1 Check that the wall frame is level before bolting it to the wall. 2 Mount the wall frame so the top edge is 5 to 6 ft (1.5 to 1.8 m) above the floor. 2 27.0 in. (685.8 mm) Wall Frame 618313 1 3/8 in. (8) places 0.5 in. (12.7 mm) 31.0 in. (787.4 mm) 3.0 in. (76.2 mm) ...

30 310564 Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on thedate of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,Grac...