Graco 334558C Manual - Free PDF Download

Page 2 - Table of Contents

2 334558C Table of Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electric Motor Kit Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3OEM Kits . . . . . ...

Page 3 - Models; Electric Motor Kit Options

Models 334558C 3 Models Electric Motor Kit Options *Performance is limited when using electric motor vs gas engine OEM Kits GH130 Model: Standard 120V Motor Kit (Non CSA) 24W923  24W924   GH200 Model: Standard ProContractor 120V Motor Kit (Non CSA) 24W925  24W926   24W927  24W928   GH230 Mo...

Page 4 - Warnings; Electric Motor Warnings; WARNING

Warnings 4 334558C Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual...

Page 6 - Gas Engine Warnings

Warnings 6 334558C Gas Engine Warnings WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: • Use equipment only in well ventilated area. • Do not fill fuel tank while engine is running or hot; shu...

Page 7 - Electric Motor/Gas Engine Warnings

Warnings 334558C 7 Electric Motor/Gas Engine Warnings WARNING SKIN INJECTION HAZARD High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, get immediate surgical treatment. • Do not aim the gun at, or spray any person or animal...

Page 10 - Component Identification

Component Identification 10 334558C Component Identification Standard Models (GH130, GH200, GH230, GH300) 2. 11. 12. 9. 1. 10. OFF ON 3. bar/MPa PSI on off 5. 4. 6. 7. ti25105a 8. 13. 14. 15. 9. 1 Engine Controls 2 Hydraulic Oil Cap / Dipstick 3 Pressure Control 4 Grounding Clamp 5 Threaded Pump Con...

Page 12 - Power Requirements

Component Identification 12 334558C Grounding Procedure for Gas Engine To ground sprayer: Attach sprayer grounding clamp to earth ground. Air and fluid hoses: Use only electrically conductive hoses with a maximum of 500ft. (150 m) combined hose length to ensure grounding continuity. Check electrical...

Page 13 - Grounding of Pails

Pressure Relief Procedure 334558C 13 Grounding of Pails Solvent pails used when flushing: Follow local code. Use only conductive metal pails, placed on a grounded surface. Do not place the pail on a non-conductive surface, such as paper or cardboard, which interrupts grounding continuity. Always gro...

Page 14 - Setup; Change Engine or Motor

Setup 14 334558C Setup Change Engine or Motor 1 Turn motor OFF and unplug or turn engine switch OFF. Loosen belt guard knob and motor clamp. Perform Pressure Relief Procedure , page 13. 2 Lift belt guard. Remove belt. Tilt engine/motor and remove engine/motor. 3 Tilt engine/motor. Install engine/mot...

Page 15 - Complete Setup

Setup 334558C 15 ti22700a Complete Setup 1. All sprayers except ProContractor: Connect appropriate Graco high-pressure hose to sprayer. 2. Install hose to spray gun and tighten securely. 3. Engage gun trigger lock. 4. Remove Tip Guard. 5. ProContractor Series: Install inlet strainer into bottom of s...

Page 16 - FROG

Setup 16 334558C 7. Fill throat packing nut with TSL to prevent premature packing wear. Do this each time you spray. 8. Check engine oil level. 9. Fill fuel tank. 10. Check hydraulic oil level. Add Graco Hydraulic Oil, ISO Grade 46, 169236 (5 gallon/18.9 liter) or 207428 (1 gallon/3.8 liter). Hydrau...

Page 17 - Startup

Startup 334558C 17 Startup 1. Place suction tube and drain tube in grounded metal pail partially filled with flushing fluid. Attach ground wire to pail and to earth ground. 2. Turn prime valve down to DRAIN position. Turn pressure control counterclockwise to lowest pressure. 3. Set hydraulic pump va...

Page 20 - Switch Tip; Spray

Startup 20 334558C Switch Tip ™ and Guard Assembly 1. Perform Pressure Relief Procedure , page 13. 2. Engage gun trigger lock. Insert Switch Tip. Insert seat and OneSeal™. 3. Insert Switch Tip and face forward. 4. Screw assembly onto gun. Tighten. Spray 1. Spray test pattern. Increase pressure to el...

Page 21 - Clear Tip Clog

Startup 334558C 21 Clear Tip Clog 1. Release trigger, engage trigger lock. Rotate Switch Tip. Disengage trigger lock. Trigger gun to clear clog. 2. Engage trigger lock. Return Switch Tip to original position. Disengage trigger lock and continue spraying. Hose Reel (ProContractor Series only) 1. Make...

Page 22 - Clean Up

Clean Up 22 334558C Clean Up 1. Perform Pressure Relief Procedure , page 13, steps 1-7. 2. Remove Guard and SwitchTip. 3. Remove siphon tube set from paint and place in flushing fluid. Use water for water-based paint and mineral spirits for oil based paint. 4. Turn engine ON and start engine or plug...

Page 24 - Maintenance

Maintenance 24 334558C Maintenance NOTE: For detailed engine maintenance and specifications, refer to separate Honda Engines Owner’s Manual, supplied. DAILY: Check engine oil level and fill as necessary. DAILY: Check hydraulic oil level and fill as necessary. DAILY: Check hose for wear and damage. D...

Page 25 - Troubleshooting

Troubleshooting 334558C 25 Troubleshooting Problem Cause Solution Gas engine pulls hard (won’t start) Hydraulic pressure is too high Turn hydraulic pressure knob counterclockwise to lowest setting Gas engine does not start Switch OFF, low oil, no gasoline Consult engine manual Fuel shut off valve cl...

Page 27 - Standard Series Pump; Removal; Installation

Standard Series Pump 334558C 27 Standard Series Pump Removal See pump manual 334654 for pump repair.1. Flush pump. 2. Perform Pressure Relief Procedure , page 13. 3. Remove suction tube and paint hose (remove at swivel end). 4. Push retaining ring up; push out pin. 5. Loosen jam nut. Unscrew pump. I...

Page 28 - ProContractor Series Pump; ProContractor

ProContractor Series Pump 28 334558C 2. Slowly pull engine starter rope until pump rod pin hole is aligned with hydraulic rod hole. Push pin into hole. Push retaining ring into groove. 3. Fill packing nut with Graco TSL. ProContractor Series Pump Removal See pump manual 334654 for pump repair.1. Flu...

Page 30 - Notes

Page 31 - Parts; GH

Parts 334558C 31 Parts GH ™ 130/200/230/300 Standard Series ti25097a

Page 33 - Parts List

Parts 334558C 33 Parts List  Danger and Warning labels are available at no cost.  Included in Drain Valve Replacement Kit 235014  Included in Drain Valve Replacement Kit 245103 ‡ Included in Filter Replacement Kit 24W753 Ref. Part Description Qty. 35 112827 BUTTON, snap 2 39 119420 WHEEL, pneumat...

Page 56 - Technical Data

Technical Data 56 334558C Technical Data GH ™ 130 Standard Series US Metric Maximum fluid working pressure . . . . . . . . 3300 psi 22.8 MPa, 228 bar Hydraulic reservoir capacity . . . . . . . . . . . . 1.25 gallons 4.75 liters Maximum hydraulic pressure . . . . . . . . . . . 1510 psi 10.4 MPa,104 b...

Page 64 - Graco Standard Warranty

Graco Standard Warranty 64 334558C Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any...

Page 65 - Graco Information

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English. MM 334558 Graco Headquarters: Minneapolis Int...