Graco 308813 - Manual

308813 5 Installation Mount the Gun Manifolds 241161 and 241162 To mount the gun on a reciprocating arm [0.5 in.(13 mm) diameter maximum], insert the bar (A)through the hole in the manifold as shown in Fig. 2.Secure the gun to the bar by tightening the mountingscrew (B). The tip of the gun should be...

308813 9 Operation Safety WARNING INJECTION HAZARD Remember, this is not an air spray gun.For your safety be sure to read andfollow the Warnings on pages 2 and 3and throughout the text of this instructionmanual. Keep the wallet sized warning card, provided withthe gun, with the operator of this equi...

10 308813 Operation Adjust Spray Pattern 1. To adjust the spray pattern direction with fan tips,orient the slot in the tip horizontally for a horizontalpattern and vertically for a vertical pattern. SeeFig. 7. 2. Start the pump. Adjust the fluid pressure until thespray is completely atomized. Use th...

308813 11 Operation Flush the Gun Daily WARNING INJECTION HAZARD To reduce the risk of an injection injury,follow the Pressure Relief Procedure on page 9 before cleaning, removing, or installing a spray tip and whenever you areinstructed to relieve pressure. WARNING To reduce the risk of serious inj...

12 308813 Troubleshooting WARNING INJECTION HAZARD To reduce the risk of an injection injury,follow the Pressure Relief Procedure on page 9 before checking or servicing any of the system equipment and whenever youare instructed to relieve pressure. NOTE: Check all possible remedies in the troublesho...

308813 13 Troubleshooting WARNING INJECTION HAZARD To reduce the risk of an injection injury,follow the Pressure Relief Procedure on page 9 before checking or servicing any of the system equipment and whenever youare instructed to relieve pressure. General Troubleshooting (continued) Problem Cause S...

14 308813 Service WARNING INJECTION HAZARD To reduce the risk of an injection injury,follow the Pressure Relief Procedure on page 9 before checking or servicing any of the system equipment and whenever youare instructed to relieve pressure. NOTE: Follow the Service Notes in Figs. 8 and 9 when reasse...

308813 15 Service 8151A Fig. 8: Gun 239786 / 241469 shown 1 3 2 4 SERVICE NOTES: 9 7 10 11 2 1 31 12 23* 13* 21 22* 20 19 18 16 17 T 25* 26* Lubricate threads with anti-seize lubricant Lubricate with light-weight oil Do not lubricate Seat gasket (11) must be replaced ifseat (10) is removed or replac...

308813 17 Service Reassembly 1. Perform the following applicable step: Non-circulating Paint Guns: Lubricate the back- up (6 ) and o-ring (5 ) and install them on the fluid outlet port plug (4). Install the plug in thefluid outlet port of the fluid housing (2). SeeFig. 9. Circulating Paint Guns: Rei...

18 308813 Parts Use Only Genuine Graco Parts and Accessories Part No. 239786, Series A Standard Automatic Airless Spray GunIncludes items 1–34 Part No. 241469, Series A Automatic Airless Acid Catalyzed Fluid Spray GunIncludes items 1–34 Part No. 233670, Series A Automatic Sealant Stream/Spray GunInc...

308813 21 GG0 Series Tip Selection Charts For Models 239786 and 241469 GG0 Series Spray Tips Flow Rate OrificeSize Fan Widthat 12” Flow Rate(tested inwater) Size inches at 12”(300 mm) water) gal/min inches(mm) (300 mm) Inches (mm) gal/min(liters/min) Part No. 0.007(0.178) 2–2.5(50–63) .053(0.20) GG0...

22 308813 GG0 Series Tip Selection Charts For Models 239786 and 241469 GG0 and GG1 Series Spray Tips Orifice Fan Width Flow Rate Part No. OrificeSize Fan Width Flow Rate Part No. 0.019(0.483) 2–2.5(50–63) 0.39(1.47) GG0119 ( ) 4–4.5(100–113) ( ) GG0219 6–6.5(150–163) GG0319 8–8.5(200–213) GG0419 10–...

26 308813 Sealer Application Tip Selection Charts For Model 233670 with tip nut 198391 Shower Tip No. of Orifices Orifice Size inches (mm) Part No. 6 0.021 (0.533) C08224 Streaming Tips Orifice Size inches (mm) Part No. Orifice Size inches (mm) Part No. 0.025 (0.635) 270025 0.037 (0.940) 270037 0.02...

308813 27 Accessories Use Only Genuine Graco Parts and Accessories GUN MANIFOLDS Order separately; not included with gun (See page 20 for Parts list) Part No. 241161, Series A North America Manifold Part No. 241162, Series A International Manifold Part No. 244930, Series A High Flow Ambient or Tempe...

28 308813 Technical Data Maximum working fluid pressure . . . . . . . . . . . . 4000 psi (28 MPa, 280 bar) Maximum working air pressure . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar) Maximum working fluid temperature . . . . . . . . 140 F (60 C) Minimum air cylinder actuation pressure . . . . . ...

30 308813 Dimensions and Mounting Holes For Guns 239786 and 241469 with Manifolds 241161 and 241162 8576A 5.23 in. (139.7 mm) 2.0 in. (50.8 mm) 3.86 in. (98.0 mm) 8581A 3.0 in. (76.2 mm) 2.125 in.(54 mm) 8722A 0.187 in. (4.8 mm) 0.805 in. (20.5 mm) 0.4 in. (10.2 mm) Two M5 x 0.8 x 0.25 in. (6.3 mm) ...

32 308813 Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on thedate of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limit...