Graco 237-410 Manual - Free PDF Download

Page 2 - Parts Change Notice

3X8–448 Rev. F Supersedes Rev. C Includes Rev. D and E changes Parts Change Notice Some parts in Rev. C of manual 308–448 have changed but have not yet been changed in theinstruction manual. Please note the changes below and mark them in your manual or keep thissheet with your manual. Assembly No. S...

Page 3 - Warning Symbol; CAUTION; P R E S S U R I Z E D F L U I D H A Z A R D; AND EXPLOSION HAZARD

Table of Contents Symbols W a r n i n g s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 S e t u p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 System Component Information . . . . . . . . . . . . . . . . . . 6 Operation . . . . ....

Page 4 - EQUIPMENT MISUSE HAZARD; TOXIC FLUID HAZARD

EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and resultin serious injury. l This equipment is for professional use only. Read all instruction manuals, tags, and labels before operating the equipment. Use the equipment only for its in...

Page 5 - Preparing the Operator

A CAUTION This equipment is compatible with most water based materials. See the wetted parts in the Tech- nical Data section and your fluid and solvent manufacturer’s compatibility information. Do not use catalyzed materials in heated applica- t i o n s . Preparing the Operator All persons who opera...

Page 7 - System Component Information; Using the; counterclockwise; VII. Using the Fluid Heater

System Component Information VI. Using the Air Spray Gun 1 . 2 . 3 . 4 . 5 . 6 . 7 . Refer to Fig. 3. Make initial fluid and air adjustments at the pumpfor maximum efficiency. If you make adjustments at the gun, take noted of what you do. Then, if the results are not satisfac-tory, you can easily re...

Page 8 - VIII. Using the Air Regulators and Needle

System Component Information VIII. Using the Air Regulators and Needle 1 . 2 . 3 . 4 . 5 . See Fig. 5. Always open air and fluid regulators slowly to pre-vent surging during startup. The air regulator (6a) on the right side of the pumpcontrols air to the pump, and the regulator (6b) onthe left side ...

Page 9 - Operation; Pressure Relief Procedure; Priming the System

Operation Pressure Relief Procedure The system remains pressurized until pressure is manually relieved. To reduce the risk of seriousinjury from pressurized fluid, accidental spray fromthe gun, or splashing of any fluid, follow this proce-dure whenever you l Are instructed to relieve pressure l Stop...

Page 10 - Setting Fiuid and Air Pressure

Operation 12. Adjust the needle valve to set the pump cycle rate at 1 stroke every 15 seconds. 13. Turn the heater dial to 3. Whenever the heater set- ting is changed, allow the fluid to circulate and sta-bilize before checking the temperature (about m i n u t e s ) . A CAUTION Be sure the fluid is ...

Page 11 - Production Spraying; When to Flush; How to Flush

Operation Production Spraying You are now ready for production spraying. If you stopspraying for more than 30 minutes, turn off the heaterto prevent overheating the fluid. VI. Shutting Down the System Shut down the system at the end of the work shift andbefore checking, adjusting, cleaning, or repai...

Page 12 - Flushina; turn; tube

Flushina 14. 15. K E Y A Bleed-type master air valve C A i r l i n e 3 F l u i d h e a t e r 6 a P u m p a i r r e g u l a t o r 6 b G u n a i r r e g u l a t o r 9 3-way valve 1 3 Drain hose 4 4 F l u i d r e g u l a t o r 4 5 F l u i d f i l t e r 4 8 F i l t e r d r a i n v a l v e For a first-ti...

Page 13 - Parts

Parts Model 237410, Series A R e f P a r t No. No. 1 235-230 2 217-752 3 220-522 4 1 1 0 - 1 6 0 5 1 0 8 - 2 3 3 6 1 1 1 - 8 0 4 7 11 O-209 8 108-l 90 9 2 1 4 - 7 1 1 1 0 214-699 1 1 205-l 69 1 2 206-966 1 3 206-965 1 4 188-l 73 1 5 165-767 1 6 188-l 07 1 7 224-044 1 8 1 5 6 - 8 4 9 1 9 2 0 803-088 ...

Page 14 - P a r t s

P a r t s Model 237410, Series A 25 23 3 0 8 - 4 4 8 1 3

Page 15 - Notes

Page 17 - The; Phone Number

Technical Data Manual Change Summary The current revision of this manual includes the following changes: Page 12, Parts List: l The quantity of item 25 (elbow) is changed to 3. l The quantity of item 47 (elbow) is changed to 1. P a g e 1 3 , P a r t s D r a w i n g : l Item 60 is changed to 62, and ...