Gemini GEM-P800 - Manual - manualsarea.com

Page 2 - Introduction; Congratulations; GEMINI Keypad; It’s easy, just always remember, in the event of an

Introduction Congratulations on your purchase of an advanced GEMINI-P800 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorpo-rates some of the most sophisticated features ...

Page 4 - G E M I N I; Keypad Controls and Indicators

ARM ED & 2 0 3 8 7 ( 5 , = ( ' 6 ( & 8 5 , 7 < 6 < 6 7 ( 0 STAT US G E M I N I 1 2 3 4 5 6 7 8 4 Keypad Controls and Indicators Status Light will light when all zones are secureand system is ready to be Armed. AC Light will light to indicatethat AC Power is present. Trouble Light will ...

Page 5 - Arming Your System

Arming Your System When Leaving 1 Before arming your system, make sure the green Status light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone number will be lit. Secure these zones before proceeding. If any zones cannot be secured, se...

Page 7 - Emergency Buttons; Emergency Conditions; Ambush Alarm

Emergency Buttons The three sets of emergency buttons, if programmed, are always active whether the system is armedor disarmed. Discuss these Buttons with your installer. The emergency signal will only be activatedwhen the two respective buttons are pressed at the same time. Fire Alarm: Simultaneous...

Page 8 - Disarming Your System / Silencing an Alarm

Disarming Your System when Returning 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your User Code and press . The red Armed light will go out, indicating that the system has been...

Page 9 - Fire Protection

Preparing a Fire Escape Plan Even with the most advanced fire alarm system, adequate protection requires an escape plan.To prepare your plan, draw floor plans of your building. (space is provided on the next page) Show two exits - a front or back door and a window from each room. (Make sure each win...

Page 11 - Special Functions

Special Functions By pressing A followed by the the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by pressing followed by . This will allow the easy arming of t...

Page 12 - System Troubles

12 The GEM-P800 is constantly monitoring its own components, as well as all critical services, such as AC power and the telephoneline, to insure that it is always ready to provide the protection for which it was designed. W hen a system trouble does occur, it willcaution you by lighting the TROUBLE ...

Page 14 - Programming User Codes

Your Installer has assigned a User 1 Code which can be used to not only Arm and Disarm the system, but also to enter the UserProgram Mode, where you can program other user codes. The following explains how you will use this code to program or eraseadditional user codes. Entering the User Program Mod...

Page 15 - Glossary

Ambush Code - In the event that you are forced by an intruder to disarm yoursystem, this special code can be used todisarm the system, and simultaneouslysend a silent alarm to Central Station. Ifyour system has the Ambush featureenabled, the code assigned as the User8 code will function as your Ambu...

Page 16 - NAPCO LIMITED WARRANTY

NAPCO LIMITED WARRANTY THE FOLLOW ING STATEMENT IS REQUIRED BY THE FCC . This equipment generates and uses radio-frequency energy and, if not installed and used properly, thatis, in strict accordance with the manufacturer's instructions, may cause interference to radio and televisionreception. It ha...

Gemini GEM-P800 - Manual

Table of Contents:

Summary

Other Gemini Models