GE GDT565SSN2SS - Installation Manual

An installation manual for built-in dishwashers outlines essential steps to ensure safe, code-compliant setup, covering electrical, plumbing, and structural preparations. The guide emphasizes safety–including grounding, wiring, and proper drainage–but also addresses practical aspects like leveling, door balance, and cabinet adjustments. It provides detailed diagrams and checklists for verifying installation readiness before finalizing connections.

Page 1 – Safety Warnings and Installation Preparation
Page 2 – Required Parts, Materials, and Tools
Page 3 – Enclosure and Drain Setup Preparation
Page 4 – Electrical Installation Requirements
Page 5 – Water Line Preparation
Page 6 – Appliance Preparation and Leveling Installation
Page 7 – Drainage and Water Line Connections
Page 8 – Unit Placement and Trim Installation
Page 9 – Mounting Brackets and Final Positioning
Page 10 – Positioning and Leveling the Unit
Page 11 – Securing Appliance and Water Supply Connections
Page 12 – Drain Line Installation Methods
Page 13 – Final Power Connection and Pretest Checklist
Page 14 – Leak Testing and Insulation Placement
Page 15 – Final Finishing Steps and Verification

Loading the manual

READ CAREFULLY

KEEP THESE INSTRUCTIONS

CHECK THE FOLLOWING

Tub trim does not interfere with the door

Dishwasher is square and level at both the top and bottom of the cabinet opening,
with no twisting or distortion of the tub or door

All 4 legs of the dishwasher are firmly in contact with the floor

Drain hose is not pinched between the dishwasher and adjacent cabinets or walls

Tub trim is fully seated on the tub flange

WARNING

CAUTION

FOR YOUR SAFETY

Read and observe all WARNINGS and CAUTIONS
shown throughout these instructions.
IMPORTANT –

Observe all governing codes and

ordinances.
•

Note to Installer

– Be sure to leave these instructions

for the consumer’s and local inspector’s use.

•

Note to Consumer

– Keep these instructions with

your Owner’s Manual for future reference.

•

Skill Level

– Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills.

Proper

installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliances Warranty. See
Warranty information.

•

Completion Time – 1 to 3 Hours

. New installations

require more time than replacement installations.

IMPORTANT –

The dishwasher MUST be installed to

allow for future removal from the enclosure if service is
required.
Care should be exercised when the appliance is
installed or removed, to reduce the likelihood of
damage to the power supply cord.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for
available custom panel kits.
Your dishwasher is a water heating appliance.

31-4000211

Rev 2

10-20 GEA

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• To reduce the risk of electric shock, fire, or injury to

persons, the installer must ensure that the dishwasher is

completely enclosed at the time of installation.

• FOR PERSONAL SAFETY: Remove house fuse or open

circuit breaker before beginning installation. Do not use

an extension cord or adapter plug with this appliance.

• The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service representative if

you are in doubt that the appliance is properly grounded.

• If house wiring is not 2-wire with ground, a ground

must be provided by the installer. When house wiring

is aluminum, be sure to use UL-Listed anti-oxidant

compound and aluminum-to-copper connectors.

• To reduce the risk of electric shock, fire, or injury to

persons, the installer should check to ensure that wires

are not pinched or damaged, the house wiring is attached

to the junction box bracket through a strain relief, and

all electrical connections made at the time of install (wire

nuts) are contained inside of the junction box cover.

Do not remove wood base until you are ready to install

the dishwasher. The dishwasher will tip over when the

door is opened if base is removed.

While performing installations described in this booklet,
gloves, safety glasses or goggles should be worn.

See your Owner’s Manual for details on how to contact us regarding installation questions

Built-In Dishwashers

Installation

Instructions

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand: GE
Model: GDT565SSN2SS
Document type: Installation Manual
Language(s): English
Pages: 16
File size: 3.6 MB
Format: PDF

Other Manuals for GE GDT565SSN2SS

User Manual

Summary

Page 1 - Safety Warnings and Installation Preparation

Safety warnings regarding electrical hazards, grounding, installation precautions, and a checklist for verifying installation readiness based on skill level and warranty.

Page 2 - Required Parts, Materials, and Tools

Listing of components supplied, necessary plumbing and electrical supplies, and required hand tools for the dishwasher installation.

Page 3 - Enclosure and Drain Setup Preparation

Preparation steps involving enclosure requirements, handle dimensions, necessary clearances, drain setup methods such as air gap or high drain loop, and cabinet preparation with associated diagrams and warnings.