Page 2 - California Safe Drinking Water and Toxic Enforcement Act
2 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING. WHAT TO DO IF YOU SMELL GAS: Do not try to light a match, or cigarette,or turn on any gas or electrical appliance. Do not touch any electrical switch; do notuse any phone in your building. Clear the room, building, or area of allocc...
Page 3 - PROPER INSTALLATION; MUST; YOUR LAUNDR Y AREA
3 PROPER INSTALLATION • Properly ground dryer to conform with allgoverning codes and ordinances. Followdetails in Installation Instructions. • Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. • Connect to a properly rated, protected andsized pow...
Page 4 - WHEN USING YOUR DR YER; DO NOT OPERATE THE; Dr y Away from Heat; Do Not Tumble Dr y; IMPORTANT SAFETY INSTRUCTIONS
4 WHEN USING YOUR DR YER • Never reach into the dryer while the drum ismoving. Before loading, unloading, or addingclothes, wait until the drum has completelystopped. • Clean the lint filter before each load toprevent lint accumulation inside the dryer or in the room. DO NOT OPERATE THE DRYER WITHOU...
Page 5 - DO NOT ATTEMPT TO LIGHT; WHEN NOT USING YOUR DR YER
IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING. 5 READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS. WHEN USING YOUR DR YER (cont.) • Never attempt to operate this appliance if it is damaged, malfunctioning, partiallydisassembled, or has missing or broken p...
Page 6 - Dryer Control Panel
Dryer Control Panel w w w. G E A p p l i a n c e s . c o m POWER MY CYCLES BACK HELP S TART S TOP HOME Features ofthe dr yercontrolpanel 1 POWER. Press to “wake up” the display. If the display is active, press to put the dryerinto standby mode. You may also press theTouch Screen or any button to “wa...
Page 7 - Quick Start; SUMMARY SCREEN; TART; Washer
7 Quick Start w w w. G E A p p l i a n c e s . c o m GettingStarted If the TouchScreen isdark, pressPOWER orthe TouchScreen toaccess thedr y cyclesmenu. Clean the lint filter. IMPORTANT: Clean the lint filter each time you use the dryer. Add clothes. Do not overload. This wastes energy and promotes ...
Page 8 - Dry Cycles
8 Dry Cycles w w w. G E A p p l i a n c e s . c o m Dr ying byFabric Type If the Touch Screen is dark, press POWER or the Touch Screen to access the dr y cycles menu. The default cycle settings are based on standard load types. Always follow the fabric manufacturer’scare label when laundering. • Ble...
Page 9 - Summary Screen; TEMPERATURE
9 Summary Screen w w w. G E A p p l i a n c e s . c o m SUMMARY SCREEN 0:36 TIME OPTIONS TEMP DRYNESS CYCLE COTTONS MORE DRY About theSummar yScreen After selecting a dr y cycle, the Summary Screen displays the automatic settings for the cycle youhave chosen. You can adjust these by touchingthe scre...
Page 10 - OPTIONS; ADJUST TIME SETTINGS; EXTENDED TUMBLE; CYCLE STATUS; DRYING
Summary Screen w w w. G E A p p l i a n c e s . c o m OPTIONS END OF CYCLE SIGNAL EXTENDED TUMBLE DELAY START OK 1 HOUR About the Dr yingOptions Touch the OPTIONS pad on the Touch Screen to select drying options. After selecting any dryingoptions, press OK to save your setting. Delay Start Touch the...
Page 11 - “My Cycles”; MY CYCLES; MY
11 “My Cycles” w w w. G E A p p l i a n c e s . c o m About the “MyCycles” Feature The “My Cycles” feature allows you to create,store and reuse up to 6 custom cycles. Create your own cycles from scratch or adjust thesettings of a predefined dry cycle; then save forone-touch recall. Creatingand Using...
Page 13 - Help; TROUBLE SHOOTER
13 Help w w w. G E A p p l i a n c e s . c o m TROUBLE SHOOTER MACHINE PREFERENCES HOME SCREEN HELP About the HelpFeature Pressing the HELP button from the HomeScreen allows you to locate troubleshooting tipsfor common dr yer problems, to find help withusing the Home Screen or to set machinepreferen...
Page 14 - MACHINE PREFERENCES
The machine settings on the Help feature allow you to control the volume of the buttonbeep and end-of-cycle signal, and turn thewasher/dryer communication feature on or off. Press the HELP button, then select from the on-screen options. Button Beep The button beep controls the volume of thebeep that...
Page 15 - Dryer Features; TIMED DRY
Changing theDrum Lamp Before replacing the drum lamp, be sure tounplug the dryer power cord or disconnect thedryer at the household distribution panel byremoving the fuse or switching off the circuitbreaker. The drum lamp is located at the top left of thedoor frame. 1 Remove the screw holding the dr...
Page 16 - Loading and Using the Dryer; Do not dr y the following items:; Wash Labels
16 Loading and Using the Dryer w w w. G E A p p l i a n c e s . c o m Sorting andLoadingHints As a general rule, if clothes are sorted properly for the washer, they are sorted properly for thedryer. Try also to sort items according to size. For example, do not dry a sheet with socks orother small it...
Page 17 - Dr yer Interior and Duct:
Dr yer Interior and Duct: The interior of the appliance and exhaust duct should be cleanedonce a year by qualified service personnel. The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and st...
Page 18 - BEFORE YOU BEGIN; IMPORTANT; Note to Installer –; Installation; WARNING; In the Commonwealth of Massachusetts:
BEFORE YOU BEGIN Read these instructions completely andcarefully. • IMPORTANT – Save these instructions for local electrical inspector’suse. • IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Kee...
Page 19 - Installation Instructions; UNPACKING YOUR DRYER; LOCATION OF YOUR DRYER; must
Installation Instructions 19 UNPACKING YOUR DRYER Tilt the dryer sideways and remove the foamshipping pads by pulling at the sides andbreaking them away from the dryer legs. Besure to remove all of the foam pieces aroundthe legs. Remove the bag containing the drying rack,literature and serial cable....
Page 21 - Adjustable pliers (to adjust leveling legs)
❒ Flat- or straight-blade screwdriver (may beneeded for cord strain relief) ❒ Flexible stainless steel or plastic-coatedbrass connecting tube (if allowed bybuilding code) ❒ Open-end wrenches for flexible tube andconnector ❒ Adjustable pliers (to adjust leveling legs) ❒ Pipe wrench for holding dryer ...
Page 22 - GAS REQUIREMENTS; DRYER GAS SUPPLY CONNECTION; Add to vertical; GAS SUPPLY; Use a pipe wrench to
22 Installation Instructions GAS REQUIREMENTS WARNING • Installation must conform to local codes and ordinances, or in their absence, theNATIONAL FUEL GAS CODE, ANSI Z223. • This gas dryer is equipped with a Valve andBurner Assembly for use only with naturalgas. Using conversion kit WE25X10014,your ...
Page 23 - Apply pipe compound or Teflon; Open the gas shutoff valve.
Install a 1/8” NPT plugged tapping to thedryer gas line shut-off valve for checkinggas inlet pressure. Install a flare union adapter to the pluggedtapping. NOTE: Apply pipe compound or Teflon ® tape to the threads of the adapter andplugged tapping. 23 Installation Instructions Attach the flexible me...
Page 24 - TEST FOR LEAKS; Never use an open; WARNING –; To reduce the risk; WARNING –; This dryer is
CONNECTING A GAS DRYER (cont.) Installation Instructions 24 TEST FOR LEAKS WARNING – Never use an open flame to test for gas leaks. Check all connections for leaks with soapysolution or equivalent. Apply a soap solution. The leak test solutionmust not contain ammonia, which couldcause damage to the ...
Page 25 - upturned ends; CONNECTING AN ELECTRIC DRYER (skip for gas dryers)
Installation Instructions 25 TOOLS AND MATERIALS YOU WILL NEED FOR CONNECTING THE ELECTRICAL SUPPLY ❒ Flat- or straight-blade screwdriver (may beneeded for cord strain relief) ❒ #2 Phillips-head screwdriver (for terminalconnections) ❒ UL-listed strain relief (may be supplied with cord) ❒ UL-listed p...
Page 26 - GROUNDING INSTRUCTIONS; Install
Installation Instructions 26 CONNECTING AN ELECTRIC DRYER (cont.) ELECTRICAL REQUIREMENTS FORELECTRIC DRYERS This dryer must be connected to an individualbranch circuit, protected by the required time-delay fuses or circuit breakers. A three- orfour-wire, single phase, 120/240V or 120/208V,60Hz, 30-...
Page 27 - Do NOT remove the long
Installation Instructions 27 For 3-wire Connection ONLY: Be sure the dryer’s green ground wire is connected to neutral (center) terminal of block and to green ground screw oncabinet rear. D For 4-wire Connection ONLY: Remove and discard the dryer’s groundwire between the cabinet and the center of th...
Page 28 - Do not obstruct incoming or exhausted air.; EXHAUST SYSTEM CHECKLIST
Installation Instructions 28 EXHAUSTING THE DRYER WARNING – To reduce the risk of fire or personal injury: • This dryer must be exhausted to theoutdoors. • Use only metal duct. • Do not terminate exhaust in a chimney, anygas vent, under an enclosed floor (crawlspace) or into an attic. The accumulate...
Page 30 - EXAMPLE ONLY; TRANSITION; YER TO W; INSIDE W; ALL TO W; ALL
EQUIVALENT RIGID NUMBER EQUIVALENT DUCT PIECES LENGTH X USED = LENGTH Rigid Metal 1 Ft. X (4) = 4 Ft. Ducting(Preferred) Elbows 10 Ft. X (3) = 30 Ft. (90°/45°) Turns Less 2 Ft. X (1) = 2 Ft. Than 4 Ft. Rigid Ducting 1 Ft. X (5) = 5 Ft. 4” Wall Cap 5 Ft. X (1) = 5 Ft. Total Ductwork Length = Ft. TOTA...
Page 31 - DUCTING COMPONENT EQUIVALENCY CHART; TRANSITION DUCTING; ALL CAPS
EQUIVALENT RIGID NUMBER EQUIVALENT DUCT PIECES LENGTH X USED = LENGTH Rigid Metal 1 Ft. X ( ) = Ft. Ducting(Preferred) Semi-Rigid 25 Ft. X ( ) = Ft. Metal Ducting(inside diameterdoes not change) Flexible Metal 50 Ft. X ( ) = Ft. Ducting (insidediameter changes) Elbows (90°/45°) 10 Ft. X ( ) = Ft. Tu...
Page 32 - STANDARD REAR EXHAUST; We strongly recommend using rigid
Installation Instructions 32 BEFORE YOU BEGIN Remove any lint from the wall exhaustopening. EXHAUSTING THE DRYER (cont.) InternalDuctOpening Wall Check thatexhaust hooddamper opensand closes freely. STANDARD REAR EXHAUST We recommend that you install your dryer before installing your washer. This wi...
Page 33 - LEVEL THE DRYER; ATTACH SERIAL CABLE; FINAL SETUP
Installation Instructions 33 LEVEL THE DRYER Stand the dryer near the final location. Place alevel against the side and bottom of the dryerdoor frame and use the four leveling legs tolevel your dryer. Lower Raise ATTACH SERIAL CABLE Attach the serial cable for washer and dryerconnection to the seria...
Page 34 - DRYER STARTUP; Press the POWER button.; SERVICING; Label all wires; YOUR DRYER IS NOW
Installation Instructions 34 DRYER STARTUP Press the POWER button. FINAL SETUP (cont.) POWER NOTE: If the dryer has been exposed to temperatures below freezing for an extendedperiod of time, allow it to warm up beforepressing POWER. Otherwise, the display willnot come on.The dryer will begin a setup...
Page 35 - REMOVE FILLER PLUGS; REMOVE DOOR; UP; and; OUT; REMOVE HANDLE; REVERSE DOOR CATCH
REMOVE FILLER PLUGS Installation Instructions 35 REVERSING THE DOOR SWING (if desired) Open the door and remove the filler plugsopposite the hinges. 1 REMOVE DOOR • With the door completely open, remove the BOTTOM screw from each hinge on thedryer face. • Insert the screws about halfway into theTOP ...
Page 36 - REVERSE HANDLE; IN; DOWN
Installation Instructions 36 REVERSE HANDLE REVERSING THE DOOR SWING (cont.) Install the handle on the opposite side of thedoor. 5 REMOVE HINGES AND REHANGDOOR Remove the hinges from the door and installthem on the opposite side with the hinge pintoward the outside of the door. 6 REMOVE HINGES AND R...
Page 37 - TOOLS YOU WILL NEED; #2 Phillips screwdriver; REMOVE WASHER BACKSPLASH
37 Installation Instructions SWITCHING THE WASHER AND DRYERBACKSPLASHES (not required for most installations) When viewed from the front, the washer isshipped for installation on the left and thedryer is shipped for installation on the right. If your hose utility connections are arrangedso that the ...
Page 38 - REMOVE DRYER BACKSPLASH; Do not disconnect any other wires
38 Installation Instructions DISCONNECT WASHERCONTROL BOARD Disconnect the ribbon at the right of the control board by pulling the connector at theend of the ribbon off the metal pins on thecontrol board. NOTE: Do not disconnect any other wires from the control board. 3 Rear of Washer REMOVE CONTROL...
Page 39 - SWITCH BACKSPLASHES
39 Installation Instructions REMOVE CONTROL BOARDFROM DRYER BACKSPLASH Remove the four screws holding the controlboard to the backsplash. Remove the controlboard and set it aside. 7 SWITCH BACKSPLASHES Place the backsplash from the dryer on top ofthe washer and place the backsplash from thewasher on...
Page 40 - ATTACH WASHER BACKSPLASH; Plug the washer and dryer back in.; buttons on both the
40 Installation Instructions RECONNECT WASHERCONTROL BOARD Connect the washer control board to thenew backsplash by sliding the ribbonconnector on the new backsplash onto themetal pins on the control board and pushingin. Make sure the ribbon is not twistedbefore inserting the connector. ATTACH WASHE...
Page 41 - Problem Solver; Using the Troubleshooter; If your dr yer will not operate, check the Problem Solver below:
41 Problem Solver w w w. G E A p p l i a n c e s . c o m Problem Possible Cause What To Do Dryer won’t operate Control panel is asleep • This is normal. Press POWER , the touch screen or any button to activate the control panel. Dryer is unplugged • Make sure cord is plugged securely intoa working o...
Page 42 - Notes
Page 43 - One Year; Second Year; Third through Fifth Year; Dryer Warranty; ll warranty service provided by our Factor y Service Centers or; Improper installation, deliver y or maintenance.
43 Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty. For The Period Of: We Will Replace: One Year Any part of the dryer which fails due to a defect in materials or workmanship. During this From the date of the full one-year warranty, GE wil...
Page 44 - Consumer Support
Consumer Support GE Appliances Web Site www.GEAppliances.com Have a question or need assistance with your appliance? Try the GE Appliances Web site 24 hours a day, any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,order parts, catalogs, or even sch...
