Page 3 - Read this Manual; If You Need Service; Safety Information
GE & You, A Service Partnership. Inside you will find many helpful hints on how to use andmaintain your range properly.Just a little preventive care onyour part can save you a greatdeal of time and money over thelife of your range. Read this Manual Ask any GE appliance owner and they willtell yo...
Page 4 - All ranges can tip and injury could result.; WARNING; IMPORTANT SAFETY NOTICE; Operating Instructions
All ranges can tip and injury could result. To prevent accidental tipping of the range, attach it to thewall and floor by installing the Anti-Tip device supplied. To check if the device is installed and engaged properly,remove the storage drawer and inspect the rear leveling leg.Make sure it fits se...
Page 5 - SAFETY PRECAUTIONS; oubleshooting T
Use this appliance only for its intended purpose asdescribed in this Owner’s Manual. When using electrical appliances, basic safety precautionsshould be followed, including the following: ■ Be sure your appliance is properly installed and grounded by a qualified technician in accordance with the pro...
Page 8 - OVEN
■ Stand away from the range when opening the oven door. Hot air or steam which escapes can cause burns to hands, face and/or eyes. ■ Do not heat unopened food containers. Pressure could build up and the container could burst, causing an injury. ■ Keep the oven vent unobstructed. ■ Keep the oven free...
Page 10 - OFF; SURFACE COOKING UNITS
IMPORTANT SAFETY INFORMATION.READ ALL INSTRUCTIONS BEFORE USING. 10 Operating Instructions Installation Instructions Safety Information Troubleshooting T ips Customer Service Use proper pan size—select cookware having flat bottomslarge enough to cover the surface unit heating element. Theuse of unde...
Page 11 - RADIANT SURFACE UNITS
Troubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information ■ Clean the cooktop with caution. If a wet sponge is used to wipe spills on a hot cooktop, be careful to avoid steam burns. ■ Keep an eye on foods being fried at high or medium high heat settin...
Page 12 - SAVE THESE INSTRUCTIONS
■ Use care when touching the cooktop. The glass surface of the cooktop will retain heat after the controls have been turned off. ■ When the cooktop is cool, use only the recommended cleaning cream to clean the cooktop. ■ To avoid possible damage to the cooking surface, do not apply cleaning cream to...
Page 13 - Using the surface units.; Troubleshooting T; How to Set; Wok Cooking; Temperature Limiter
13 Using the surface units. Troubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information How to Set Push the knob in and turn in either direction to thesetting you want. At both OFF and HI the control clicks into position. You may hear slight clicking so...
Page 14 - Indicator Lights; Dual Surface Unit Switch
Using the surface units. Operating Instructions Installation Instructions Safety Information Troubleshooting T ips Customer Service Indicator Lights (glass cooktops only) A HOT COOKTOP indicator light will glow when any radiant element is turned on, and will remain on until the surface is cool enoug...
Page 15 - Selecting types of cookware.; Porcelain Enamel Covered Cast Iron:
Troubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Selecting types of cookware. (glass cooktops only) The following information will help you choose cookware which will give good performance. Stainless Steel: recommended Aluminum: heavy weight ...
Page 16 - Using the oven controls.; Clock and Timer Features; COOKING TIME Pad
Using the oven controls. 16 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service Throughout this manual, features and appearance may vary from your model. Clock and Timer Features COOKING TIME Pad Press this pad and then press the + or – pad to ...
Page 17 - Oven Control Settings; ALL; SELF CLEAN Pad; BAKE Pad; Display
Oven Control Settings + and – Pads These pads allow you to set times up to 9 hours and 59minutes. Short taps to these pads change the time ortemperature by small amounts. Press and hold the pad tochange the time or temperature by larger amounts. CLEAR/OFF Pad Press this pad to cancel ALL oven operat...
Page 18 - Special features of your oven control.; When the display shows your choice press the; START; features will remain in memory after a power failure.; Fahrenheit or Centigrade Temperature Selection
Special features of your oven control. 18 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service 12 Hour Shut-Off With this feature, should you forget and leave the oven on, thecontrol will automatically turn off the oven after 12 hours duringbaki...
Page 19 - Control Lockout; Tones at the End of a Timed Cycle
19 Troubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Control Lockout Your control will allow you to lock down the touch pads so theycannot be activated when pressed. Press the BAKE and BROIL HI/LO pads at the same time for 2 seconds until the ...
Page 20 - BAKE
20 Special features of your oven control. Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service 12 Hour, 24 Hour or Clock Black-Out Your control is set to use a 12 hour clock. If you would prefer to have a 24 hour military time clockor black-out ...
Page 21 - Changing the Speed of the + or – Pads; Cook and Hold
21 Troubleshooting T ips Installation Instructions GECustomer Service Operating Instructions Safety Information Changing the Speed of the + or – Pads As you use the + or – pads when setting a time or temperature, you may notice the display changes slowly. This special feature allowsyou to change the...
Page 22 - Before you begin...; How to Set the Oven for Baking or Roasting; Type of Food
To avoid possible burns, place the shelves in the desired position before you turn the oven on. Before you begin… The shelves have stop-locks, so that when placedcorrectly on the supports, they will stop before comingcompletely out, and will not tilt.When placing and removing cookware, pull the shel...
Page 23 - Aluminum Foil; LO Broil; Preheating and Pan Placement
23 Troubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Aluminum Foil Never entirely cover a shelf with aluminum foil. This willdisturb the heat circulation and result in poor baking. A smaller sheet of foil may be used to catch a spillover bypla...
Page 25 - Using the clock and timer.; CLOCK
Using the clock and timer. Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information The clock must be set for the automatic oven timingfunctions to work properly. The time of day cannot bechanged during a timed baking or self-cleaning cycle. To Set ...
Page 26 - Using the timed baking and roasting features.
Using the timed baking and roasting features. 26 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service Do not latch the oven door during timed cooking. The latch is used for self-cleaning only. NOTE: Foods that spoil easily, such as milk, eggs, f...
Page 27 - How to Set a Delay Start and Automatic Stop
Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information How to Set a Delay Start and Automatic Stop Make sure the oven clock shows the correct time of day. Press the BAKE pad. Using the + or – pad, enter the desired temperature. Press the COOKING T...
Page 28 - Adjust the oven thermostat—Do it yourself!; To Adjust the Thermostat
Adjust the oven thermostat—Do it yourself! 28 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service You may find that your new oven cooks differently than the one it replaced.Use your new oven for a few weeks to become more familiar with it. If y...
Page 29 - Before a Clean Cycle
Using the self-cleaning oven. Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Never force the latch handle. Forcing the handle will damage the door lock mechanism. Wipe up heavy soil on the ovenbottom. 29 Before a Clean Cycle The range must...
Page 30 - How to Set the Oven for Cleaning
Using the self-cleaning oven. Never force the latch handle. Forcing the handle will damage the door lock mechanism. 30 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service How to Set the Oven for Cleaning Latch the door. Press the SELF CLEAN pad...
Page 31 - How to Delay the Start of Cleaning
Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information How to Delay the Start of Cleaning Latch the door. Press the SELF CLEAN pad. Using the + or – pad, enter the desired clean time. Press the START TIME pad. The earliest start time you can set w...
Page 32 - Care and cleaning of the range.; Control Panel and Knobs
Care and cleaning of the range. 32 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service If your range is removed for cleaning, servicing or any reason, be sure the anti-tip device is re-engaged properly when the range is replaced.Failure to take...
Page 33 - Painted Surfaces; sure grip; Sure Grip Handle
33 Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Painted surfaces include the sides and the drawer front. Clean these with soap and water or a vinegar and water solution. Do not use commercial oven cleaners, cleaning powders, steel woolor...
Page 34 - To clean the inside of the door:
Care and cleaning of the range. 34 Lift-Off Oven Door The oven door is removable for cleaning. Do not lift the door by the handle. To remove the door, open it to the special stop position. Grasp firmly on each side and lift the door straight upand off the hinges. Do not place hands between the hinge...
Page 35 - Oven Heating Elements; Before replacing your oven light bulb,; To replace the cover:
Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information 35 Oven Heating Elements Do not clean the bake element or the broil element. Any soil will burn off when the elements are heated. To clean the oven floor, gently lift the bake element.Clean wi...
Page 36 - Porcelain Enamel Cooktop
Be sure all surface units are turned offbefore raising the cooktop. Care and cleaning of the range. 36 Lift-Up Cooktop (electric coil models only) Some models have a cooktop that can be lifted up for easier cleaning. The entire cooktop may be lifted upand supported in the up position. The surface un...
Page 37 - Surface Units; To remove a surface unit:; Drip Pans
Be sure all the controls are turned to OFF and the surface units are coolbefore attempting to remove them. Surface Units (electric coil models only) To clean the surface units, turn the control to the highestsetting for a minute. The coils will burn off any soil. To remove a surface unit: To remove ...
Page 38 - Cooktop Surface Light
Cooktop Surface Light When changing a cooktop light, do not touch the metal at the endsof the light. The cooktop light is easily replaced with a fluorescenttube of the same wattage. Before changing the light,pull the plug to the range or disconnect the power at themain fuse or circuit breaker panel....
Page 39 - To remove the storage drawer:; To replace the storage drawer:
39 Broiler Pan & Grid After broiling, remove the broiler pan from the oven.Remove the grid from the pan. Carefully pour out thegrease from the pan into a proper container. Wash and rinse the broiler pan and grid in hot waterwith a soap-filled or plastic scouring pad. If food has burned on, sprin...
Page 40 - Cleaning the glass cooktop.; To clean the cooktop seal,; let a wet cloth rest on it for a few minutes, then; National Parts Center; Daily Cleaning
Cleaning the glass cooktop. 40 Clean the glass surface with cleaning cream before you use the cooktop forthe first time. Also, clean the glass surface after each use. This helpsprotect the top and makes clean-up easier. To clean the cooktop seal, let a wet cloth rest on it for a few minutes, then wi...
Page 41 - Special Care
41 Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Special Care Be sure to use a new sharp razor scraper. Do not use a dull ornicked blade. Sugary spillovers (such as jellies, fudge, candy syrups) ormelted plastics can cause pitting of the ...
Page 42 - Installation of the range.; Before You Begin; Tools You Will Need
Installation of the range. 42 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service Read these instructions completely and carefully. Before You Begin IMPORTANT: Save these instructions for the local electrical inspector’s use. IMPORTANT: OBSERVE...
Page 43 - Prepare the Opening; Read these instructions completely and carefully.
Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Prepare the Opening Allow 1 1 ⁄ 2 ″ spacing from the range to adjacent vertical walls above cooktop surface. Allow 30 ″ minimum clearance between surface units and bottom of unprotected wood o...
Page 44 - Flooring Under the Range
Installation of the range. 44 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service Read these instructions completely and carefully. Flooring Under the Range Your range, like many other household items, is heavy and can settle into soft floor co...
Page 45 - Power Cord Strain Relief Installation
45 Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Power Cord Strain Relief Installation Remove the lower rear range wiring cover to expose the connector blockand bracket. Remove the knockout ring (1 3 ⁄ 8 ″ ) located on bracket directly be...
Page 46 - -Wire Power Cord Installation; The neutral or ground wire of the power cord
Installation of the range. 46 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service Read these instructions completely and carefully. 3-Wire Power Cord Installation WARNING: The neutral or ground wire of the power cord must be connected to the ne...
Page 47 - -Wire Power Cord Installation; The neutral wire of the supply circuit; Before
47 Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information 4-Wire Power Cord Installation WARNING: The neutral wire of the supply circuit is connected to the neutral terminal located in the center of theconnector block. The power leads must be conn...
Page 48 - -Wire Conduit Installation; Connector block is approved for copper wire connection
Installation of the range. 48 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service Read these instructions completely and carefully. 3-Wire Conduit Installation Remove the 3 screws from the connector block. Insert bare wires between theconnector...
Page 49 - -Wire Conduit Installation
49 Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information 4-Wire Conduit Installation Remove the 3 screws from the connector block. Remove the grounding strapfrom the connector block middle location and the screw connecting it to theframe of the r...
Page 50 - Anti-Tip Bracket Installation; Leveling the Range; Final Check; Be sure all range controls are in the; position before leaving the range.
Installation of the range. 50 Operating Instructions Installation Instructions Safety Information Tr oubleshooting T ips Customer Service Read these instructions completely and carefully. Anti-Tip Bracket Installation An Anti-Tip bracket is supplied with instructions for installation in a variety of...
Page 51 - Before you call for service...; Problem
Before you call for service… Tr oubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Troubleshooting TipsSave time and money! Review the charts on the following pagesfirst and you may not need to call for service. Problem Possible Causes What To Do...
Page 52 - Troubleshooting Tips
Before you call for service… Troubleshooting Tips Operating Instructions Installation Instructions Safety Information Troubleshooting T ips Customer Service Problem Possible Causes What To Do Electric Coil Models Surface units The surface units are • With the controls off, check not functioning not ...
Page 53 - Oven will not work
Troubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information Problem Possible Causes What To Do Oven will not work Plug on range is not • Make sure electrical plug is completely inserted in plugged into a live, properly the electrical outlet. grounded ou...
Page 57 - General Electric Company; GE Service Protection Plus; GE, a name recognized worldwide for quality and dependability,; Please place in envelope and mail to:
57 General Electric Company Warranty Registration DepartmentP.O. Box 34070Louisville, KY 40232-4070 GE Service Protection Plus ™ GE, a name recognized worldwide for quality and dependability, offers you Service Protection Plus ™ —comprehensive protection on all your appliances— No Matter What Brand!...
Page 58 - Consumer Product Ownership Registration
Consumer Product Ownership Registration Model Number Serial Number Important Mail Today! GE Appliances General Electric CompanyLouisville, Kentucky 40225 First Name Mr. ■ ■ Ms. ■ ■ Mrs. ■ ■ Miss ■ ■ Street Address City State Date Placed In Use Month Day Year Zip Code Apt. # Last Name Phone Number _ ...
Page 59 - GE Electric Range Warranty; One Year; Five Years; What GE Will Not Cover:
Troubleshooting T ips Installation Instructions Customer Service Operating Instructions Safety Information GE Electric Range Warranty All warranty service provided by our Factory Service Centers, or an authorized Customer Care ® technician. For service, call 800-GE-CARES. For The Period Of: We Will ...
Page 60 - Customer Service; Service Telephone Numbers.
Printed in Louisville, KY Operating Instructions Installation Instr uctions Safety Information Tr oubleshooting T ips Customer Service Service Telephone Numbers. The GE Answer Center ® is open 24 hours a day, 7 days a week. GE Answer Center ® 800.626.2000 Expert GE repair service is only a phone cal...