Page 2 - Comments... Suggestions... Corrections...; Copyright and Trademarks
Comments… Suggestions… Corrections… The User Documentation Department would like toknow your opinion of this manual. Your feedback helpsus optimize our documentation to suit your individual needs. Feel free to send us your comments by e-mail to [email protected] . Certified documentation ac...
Page 3 - Technical Manual; Contents
D2529 (TX300 S4) Technical Manual Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.2 CE Certificate . . . . . . . . . ....
Page 5 - Introduction; Notational conventions; italics
D2529 (TX300 S4) Technical Manual 5 1 Introduction This technical manual describes the system board D2529, which can be equipped with one or two Intel ® processors. You will find further information in the BIOS description. Fur ther information about drivers is provided in the readme files on the ha...
Page 7 - Important notes; Notes on safety
D2529 (TX300 S4) Technical Manual 7 2 Important notes In this chapter you will find essential information regarding safety when working with your server. V CAUTION! With the system board installed you must open the system to access the system board. How to access the system board of your system is d...
Page 8 - Batteries; It is essential to observe the instructions in
8 Technical Manual D2529 (TX300 S4) Notes on safety Important notes V ● Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. There is a danger of burns!. ● Transmission lines to peripheral devices must be adequately shielded....
Page 10 - Notes about boards; CE Certificate; Compliance was tested in a typical PRIMERGY configuration.
10 Technical Manual D2529 (TX300 S4) CE Certificate Important notes Notes about boards ● During installation/deinstallation of the system board, observe the specific instructions described in the service manual for the server. ● Remove the plug from the mains outlet so that system and system board a...
Page 11 - Environmental Protection
D2529 (TX300 S4) Technical Manual 11 Important notes Environmental Protection 2.3 Environmental Protection Environmentally friendly product design and development This product has been designed in accordance with standards for ”environmen-tally friendly product design and development“. This means th...
Page 12 - Returning, recycling and disposal
12 Technical Manual D2529 (TX300 S4) Environmental Protection Important notes Returning, recycling and disposal For details on returning and reuse of devices and consumables within Europe, refer to the “Returning used devices” manual, or contact your Fujitsu Siemens Computers branch office/subsidiar...
Page 13 - Features; Overview; Processors
D2529 (TX300 S4) Technical Manual 13 3 Features 3.1 Overview Processors – 1 or 2 dual or quad core Intel ® Xeon™ processors – 2 processor sockets LGA771 for dual core Intel ® Xeon™ processors – 1x6, 2x6, 2x4 or 4 MB Second-Level-Cache (on-die unified, 64 byte cache-line size) – 32 KB L1 Cache (on-di...
Page 17 - Main memory; Slots for riser cards; If only one riser card is occupied slot DIMM A/B will be populated.
D2529 (TX300 S4) Technical Manual 17 Features Main memory 3.2 Main memory The system board suppor ts up to 64 Gbyte main memory. Two slots for riser cards with 8 FBD slots each are available . Each memory bank can be populated with two 512 Mbyte, 1 Gbyte, 2 Gbyte or 4 Gbyte FBD PC2-4200F or FDB PC2-...
Page 20 - Sparing mode
20 Technical Manual D2529 (TX300 S4) PCI(e) slots Features Sparing mode Only one riser card is required for the sparing mode. The last populated bank will be in hotspare mode. 1A + 1B, 2A +2B minimum configuration, bank 2 in hotspare mode 1A + 1B, 2A +2B, 3A +3Bupgrade 1, bank 3 in hotspare mode 1A ...
Page 22 - Assignment of the PCI interrupts; Auto; Property
22 Technical Manual D2529 (TX300 S4) PCI(e) slots Features The following interrupt signals are used in the system: Assignment of the PCI interrupts If you select Auto in the BIOS setup, the interrupts are assigned automatically and no fur ther settings are required. Slot/device Property Interruptsig...
Page 23 - Screen resolution; The following functions are suppor ted:; Temperature monitoring
D2529 (TX300 S4) Technical Manual 23 Features Screen resolution 3.4 Screen resolution Depending on the operating system used the screen resolutions in the following table refer to the graphic controller on the system board. The graphic controller is integrated in the iRMC (integrated Remote Manageme...
Page 25 - LEDs
D2529 (TX300 S4) Technical Manual 25 Features LEDs 3.6 LEDs Figure 5: LEDs on the system board No r t h br idge Sout h br idge System F an 2 System F an 1 System F an 3 System F an 4 C PU 1/ 2 F an s C PU 1 C PU 2 - C PU F an 2 C PU F an 1 A B N M N M C K G D D D D D D D I H E E F F F F F F
Page 26 - LED Anzeige
26 Technical Manual D2529 (TX300 S4) LEDs Features Figure 6: LEDs on the riser card LED s A, B and C are visible from outside on the rear of the server. All the other LEDs are only visible, if the cover of the server has been opened. If the server has been powered off (power-plugs must be disconnect...
Page 28 - Interfaces and connectors
28 Technical Manual D2529 (TX300 S4) Interfaces and connectors Features 3.7 Interfaces and connectors Figure 7: Schematic view of the system board D2529 System F an 1 System F an 3 System F an 2 System F an 4 C PU 1 C PU 2 C PU F an 2 C PU F an 1 1 2 3 4 5 67 8 9 10 11 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 ...
Page 29 - 0 = Floppy disk drive
D2529 (TX300 S4) Technical Manual 29 Features Interfaces and connectors 1 = PCI slots 12 = SATA4 2 = external ports 13 = SATA2 3 = slots for main memory modules 14 = CPU 1/2 fan 4 = Power supply PWR2 15 = Intrusion 5 = Power supply PWR3 16 = USB 2 AUX 6 = PC98 17 = USB 1 AUX 7 = Power supply PWR1 18...
Page 30 - External ports; = Serial interface COM1
30 Technical Manual D2529 (TX300 S4) Interfaces and connectors Features 3.7.1 External ports Figure 8: External ports of the system board D2529 The serial interface COM1 can be used as default interface or to communicate with the iRMC. 1 = Printer por t (optional) 7 = USB port 4 2 = PS/2 mouse conne...
Page 32 - Settings with DIP switches; Off
32 Technical Manual D2529 (TX300 S4) Settings with DIP switches Features Figure 10: LAN connector service LAN controller 3.8 Settings with DIP switches Figure 11: DIP switch I Preset for switches 1 to 4 = Off . Recovering System BIOS (recovery switch) - switch 1 Switch 1 enables recovery of the old ...
Page 35 - Replacing the lithium battery
D2529 (TX300 S4) Technical Manual 35 4 Replacing the lithium battery In order to save the system information permanently, a lithium battery is installed to provide the CMOS-memory with a current. When the charge is too low or the battery is empty, a corresponding error message is provided. The lithi...
Page 37 - Abbreviations
D2529 (TX300 S4) Technical Manual 37 Abbreviations The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described system board. ACPI Advanced ...
