Page 2 - TABLE OF CONTENTS
2 PB Table of Contents INTRODUCTION 3 Important Safety Information 3 Personal Injury Or Death Hazards 4 FCC Caution 5 FRIEDRICH CONNECT 6 Kuhl, Kuhl Q, And Wallmaster Controls 6 KUHL, KUHL Q, AND WALLMASTER 8 Wi-Fi SET UP INSTRUCTIONS 8 Wi-Fi TROUBLESHOOTING TIPS 12 FRIEDRICH GO 14 FA Pro/ FA Premie...
Page 3 - Your safety and the safety of others is very; WARNING; NOTICE; CAUTION; result to you or others.; INTRODUCTION; IMPORTANT SAFETY INFORMATION
3 PB Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is a safety Alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others...
Page 4 - SAFETY; Make sure to follow proper lockout/tag out procedures.; PERSONAL INJURY OR DEATH HAZARDS
4 PB SAFETY FIRST WARNING AVERTISSEMENT ADVERTENCIA Do not remove, disable or bypass this unit’s safety devices. Doing so may cause fire, Doing so may cause fire, injuries, or death. Ne pas supprime, désactiver ou contourner cette l´unité des dispositifs de sécurité, faire vous risqueriez de provoqu...
Page 5 - FCC Caution; Reorient or relocate the receiving antenna.
5 PB INTRODUCTION FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operati...
Page 6 - FRIEDRICH CONNECT; There are three control push buttons on each side of the display.; CONTROL PANEL AND DISPLAY
6 PB FRIEDRICH CONNECT Kuhl, Kuhl Q, And Wallmaster Controls All of the control panel function buttons and mode icons can be viewed in Figures 201. Power On – Press the button to turn on the air conditioner. The power button illuminates to in - dicate that the power is on. The backlight on the power...
Page 7 - This menu is used to turn on Wi-Fi connection.; MENU RETURN
7 PB The CnCT Menu (WiFi Connection) This menu is used to turn on Wi-Fi connection. This is the CnCT menu. See Figure 202 Pressing the menu button will activate Wi-Fi. To setup WiFi, refer to Wi-Fi setup instructions. Figure 202 MENU RETURN Figure 203 MENU RETURN FRIEDRICH CONNECT Kuhl, Kuhl Q, And ...
Page 8 - Wi-Fi SET UP INSTRUCTIONS
8 PB Wi-Fi SET UP INSTRUCTIONS Below are the set-up instructions for Wi-Fi to use your unit wirelessly. Follow the instructions below: 1. Write down the following information prior to beginning this process (If you do not know this information you can check your router or contact your internet provi...
Page 9 - first attempt, you may need to reset the Air Conditioning
9 PB Wi-Fi SET UP INSTRUCTIONS (CONT) 6. To start the setup process click the menu button on the Control Panel. NOTE: If the Display is not illuminated, you will need to need click the menu button to illuminate the Display and then click it again to start the setup process. 7. Using the up and down ...
Page 10 - Your device may auto populate the fields
10 PB Wi-Fi SET UP INSTRUCTIONS (Continued) 10. Go to the Wi-Fi settings on your mobile device and connect to “FriedrichConnect_xxxx” network. (xxxx is the network name of the Friedrich unit) Step 10 (Connect WiFi to “Friedrich”) Step 11 (Click next) 12. A screen will appear asking you to enter your...
Page 11 - Please connect back to your Wi-Fi network and click “Next”.; NOTE; the list ready. “Please wait, this may take up to 3 minutes”.; Please wait and do not close out the box that appears.
11 PB 14. Click next. NOTE: You will receive a pop up box message stating “Credentials successfully saved. Please connect back to your Wi-Fi network and click “Next”. NOTE: You will receive a message (Waiting for network connection). 15. Go back to the Wi-Fi settings on your mobile device and connec...
Page 12 - If you received this error message
12 PB FRIEDRICH CONNECT KUHL, KUHL Q, AND WALLMASTERWi-Fi TROUBLESHOOTING TIPS If you received this error message “Error in association process: Request has been terminated Possible causes: the network is offline, Origin is not allowed by Access-Control-Allow-Origin, the page is being unloaded, etc....
Page 13 - FRIEDRICH GO; Please read the manual carefully before using the product and
13 PB FRIEDRICH GO Thank you for choosing a FRIEDRICH product and welcome to the FRIEDRICH family. This manual only applies to air conditioners which have Wi-Fi functionality. Please read the manual carefully before using the product and keep it for further reference. Please do not unplug the Wi-Fi ...
Page 14 - iOS; App Info; iOS; Wi-Fi App Installation and Instruction Manual; iOS; using a Wi-Fi channel broadcasting in 2.4GHZ
14 PB Wi-Fi App Installation and Instruction Manual Scan the QR code below using your camera function to download the latest FriedrichGo app software. The FriedrichGo app can also be found in the Apple iTunes or Google Play stores. FriedrichGo Please note-The FriedrichGo App is supported on 2.4 GHZ ...
Page 15 - SIGN UP YOUR USER ACCOUNT
15 PB FRIEDRICH GO FA Pro/ FA Premier SIGN UP YOUR USER ACCOUNT Once you download the App, you will need to create an account. Click the “Sign up” button to begin the registra- tion process. You can register with your email address or with a mobile phone number. Register with an email address: Regis...
Page 16 - SIGN IN TO YOUR USER ACCOUNT; phone number that was used for registration.; Follow these below steps to retrieve a forgotten password:
16 PB FRIEDRICH GO FA Pro/ FA Premier SIGN IN TO YOUR USER ACCOUNT Once you have created an account, click the “Sign In” button to sign in to your account using the email or mobile phone number that was used for registration. You can update your home name and select the rooms. Follow these below ste...
Page 20 - AIR CONDITIONER CONTROL; control your Air Conditioner remotely.
20 PB FRIEDRICH GO FA Pro/ FA Premier AIR CONDITIONER CONTROL 1. Tapping the Air Conditioners name to enter the control mode. Tapping the ON/OFF button for power and then control your Air Conditioner remotely. 2. Adjusting settings for operation mode, Fan, Dry, Heat or Cool. Tap the “Mode” button an...
Page 22 - finished setting the timer, click the button to Cancel or Save.
22 PB FRIEDRICH GO FA Pro/ FA Premier 5. To set the Time Function: Tap “Timer”, the App will enter the timer setting screen. Display will show the sched- ules that were previously set. You can press to edit or add new timers.(Note: Timer is 24hr clock). 6. Click “ON” or “OFF” button to set Timer ON ...
Page 24 - enabled, you will have to use pattern to unlock app.
24 PB FRIEDRICH GO FA Pro, FA Premier 9. Pattern unlock: Tap “Gesture unlock” under the personal center. Here you can set up an unlock pattern. Once enabled, you will have to use pattern to unlock app. Note: The first registered mobile device is the main control and other devices can only be shared ...
Page 25 - FA Pro, FA Premier Troubleshooting
25 PB FRIEDRICH GO FA Pro, FA Premier Troubleshooting Description Analysis Air Conditioner set up unsuccessful! 1. Check that the Wi-Fi address and password is correct for the network you are trying to connect to. 2. Check the air conditioner under configuration status. 3. Check to make sure no fire...
Page 26 - Chill Premier/ Unifit App Info
26 PB FRIEDRICH GO Chill Premier/ Unifit App Info Thank you for choosing a FRIEDRICH product and welcome to the FRIEDRICH family. This manual only applies to air conditioners which have Wi-Fi functionality. Please read the manual carefully before using the product and keep it for further reference.P...
Page 28 - Register with an email address:; Register with an email address:; Chill Premier/ Unifit Registration; complete the registration process.
28 PB REGISTER YOUR USER ACCOUNT Once you download the App, you will need to create an account. Click the "Register" button to begin the registration process. You can register with your email address OR with a mobile phone number Register with an email address: Register with a mobile phone n...
Page 29 - LOGIN TO YOUR USER ACCOUNT; LOGIN TO YOUR USER ACCOUNT
29 PB LOGIN TO YOUR USER ACCOUNT Once you have registered and created an account, click the "Login" button. You will be able to login with the email account you registered with or the mobile phone number you registered with. You can set up your home name and select the rooms. 3 If you forget...
Page 30 - AFTER INSTALLING THE FriedrichGo APP ON YOUR MOBILE DEVICE,; CF Mode; device will be synced together afterwards.; There are
30 PB AFTER INSTALLING THE FriedrichGo APP ON YOUR MOBILE DEVICE, YOU MUST THEN ADD YOUR AC UNIT TO BE CONTROLLED BY YOUR INSTALLED APP. FOLLOW THE DIRECTIONS BELOW: 1.Press the "Add Device" and click the type of product you are connecting to. There are two setup Modes/Methods to connect the...
Page 31 - ADD THE AC UNIT TO THE WIRELESS NETWORK USING CF MODE; ADD THE AC UNIT TO THE WIRELESS NETWORK USING “C F MODE”
31 PB ADD THE AC UNIT TO THE WIRELESS NETWORK USING CF MODE " " 1. . The App and AC unit automatically defaults to CF mode upon start up. Follow the prompts on the screen and then press " Next Step" to continue. 2 Select the network you wish to connect to, enter the router password a...
Page 32 - ADD THE AC UNIT TO THE WIRELESS NETWORK USING AP MODE; ADD THE AC UNIT TO THE WIRELESS NETWORK USING AP MODE; the AC unit as a mobile hotspot)
32 PB 5. Note: If at any time you need to start over- Pressing "Display" on the remote control 6 times will reset the wireless setup configuration on the AC unit back to CF mode. Pressing the Display button an additional 6 times after CF mode appears will switch the unit to AP mode. Please a...
Page 34 - the FriedrichGo App to resume setup.; take 10-15 seconds to connect the AC to the network.
34 PB 7.Connect to the SmartLife-xxxx network. 8. After connecting to "SmartLife -xxxx" network using the AC unit s Wi-Fi adapter, return to the FriedrichGo App to resume setup. 9.The AC unit will automatically begin installing/syncing on the mobile device. ' 10.The AC unit s LED screen may ...
Page 36 - on AC units that are cool only.
36 PB AIR CONDITIONER CONTROL 1.Click the air conditioner name to enter the App control panel. Click the ON/OFF button to adjust the settings. 2.You can adjust the settings for the operating mode you want to use: Cool, Heat, Dry, Fan, Auto. Click the "Mode" button and choose the mode you wou...
Page 37 - the fan speed will be set to low only.
37 PB 3.For Fan mode, click the "Fan" button and choose the speed you want: Low, Med, High, Auto. 11 4.Other unit controls can be changed by selecting the "Function" button. By selecting the Function control, you can select the Sleep or Eco modes. In Sleep mode, the fan speed will be...
Page 40 - to unlock the App.
40 PB 14 9.Pattern unlock. Tap "Pattern unlock" under the Profile section where you set your name. You can then set up your App unlock pattern. After it is enabled, you need to draw the pattern to unlock the App. FRIEDRICH GO Chill Premier/ Unifit 9. Pattern unlock. Tap “Pattern unlock” unde...
Page 41 - Chill Premier/ Unifit Troubleshooting
41 PB FRIEDRICH GO Chill Premier/ Unifit Troubleshooting Description Analysis Air conditioner can’t be set up and configured successfully 1. Check that the Wi-Fi address and password is cor- rect for the network you are trying to connect to.2. Check the air conditioner under configuration status.3. ...
Page 42 - TECHNICAL SUPPORT
42 PB Friedrich Air Conditioning Co. 10001 Reunion Place, Suite 500 • San Antonio, Texas 78216 1-800-541-6645 www.friedrich.com TECHNICAL SUPPORT CONTACT INFORMATION CUSTOMER SATISFACTION and QUALITY ASSURANCE Friedrich is a conscientious manufacturer, concerned about customer satisfaction, product ...
