Fisher & Paykel OB90S9MEPX1 - User Manual
Fisher & Paykel OB90S9MEPX1 Oven – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PRODUCT DIMENSIONS; CABINETRY DIMENSIONS
- Page 3 – E N; UNPACK THE OVEN
- Page 4 – TROUBLESHOOTING
WARNING!
Electrical hazard
Always disconnect the oven from
the mains electricity supply
before carrying out any
maintenance operations or
repairs.
Failure to do so may result in
electrical shock or death.
Important safety instructions!
To avoid hazard, follow these instructions carefully before installing or using this product.
Please make this information available to the person installing the product as it could reduce your
installation costs.
This oven is to be installed and connected to the electricity supply only by an authorised person.
If the installation requires alterations to the domestic electrical system, call a qualified electrician. The
electrician should also check that the power supply cable section is suitable for the electricity drawn by the
oven.
The oven must be earthed.
Do not use adapters, reducers or branching devices to connect the oven to the mains electricity supply,
as they can cause overheating and burning.
Installation must comply with your local building and electricity regulations.
Failure to install the oven correctly could invalidate any warranty or liability claims.
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our local
website listed at the end of this document or contact your local Fisher & Paykel dealer.
SAFETY AND WARNINGS
WARNING!
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
1
Before you install the oven, please make sure that
it will be lifted by two people.
the oven will rest on a flat surface that can support its weight.
the benchtop and oven cavity are square and level, and are the required dimensions.
the height from the floor suits the customer.
the oven door can open fully without obstruction.
a suitable isolating switch providing full disconnection from the mains power supply (under overvoltage
category III conditions) is incorporated in the permanent wiring, mounted and positioned to comply with
the local wiring rules and regulations. The isolating switch must be of an approved type and provide a 3
mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow
for this variation of the requirements).
the electrician provides sufficient free length of power supply cable to reach from the bottom rear of the
cavity to at least 1.5 metres in front of the bottom edge of the opening. The cable may enter the cavity
from the side, top or bottom, but top entry must be at the rear of the cavity.
When you install the oven
Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher &
Paykel will not cover the costs of removing the oven, or of damage caused by this removal.
Use the supplied screws to secure the oven to the cabinetry. Do not over-tighten the screws.
Make sure that the power supply cable will not touch any hot metal parts.
Make sure that the isolating switch will be easily accessible by the customer.
Do not stand on the door, or place heavy objects on it.
Do not lift the oven by the door handle.
Take extra care not to damage the lower trim of the oven. We suggest you place the unpacked oven onto
wooden blocks or similiar supports.
When handling the oven, take care not to damage the door sensor lever
(near the top right corner of the oven seal).
Use easy-to-clean finishes for the wall surfaces surrounding the oven, so that cooking fume staining
resulting from using the oven is easy to remove.
IZONA CookSpace multifunction pyrolytic oven
Installation instructions
OB90 models
NZ AU GB IE
124 lb
56 kg
WARNING!
Very Heavy
Do not attempt to lift this
product
unassisted.
Lifting unassisted may
cause serious injury.
(1,1) -1- 599790A izonacsOB90oven install A2 NZGB.indd 15/6/09 10:57:43 AM
(1,1) -1- 599790A izonacsOB90oven install A2 NZGB.indd 15/6/09 10:57:43 AM
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 PRODUCT DIMENSIONS A B C E F G H Product dimensions (mm) OB90 models A overall height of product (including upper and lower vents) 478 B overall width of product 896 C overall depth of product (without handle and dials) 566 D height of chassis at the rear 462 D I overall height of chassis 467 E ma...
E N L 1 (L ) 2 1 2 4 1 2 3 4 5 6 7 UNPACK THE OVEN REMOVE THE DOOR ELECTRICAL CONNECTION HARD WIRING THE OVEN Rating plate Unhook to open cover Unhook to open cable clamp We recommend that the outlet for the power supply cable is located in the right rear corner of the cabinet cavity. This allows th...
8 9 3 4 1 2 3 1 2 SECURE THE OVEN TO THE CABINETRY REFIT THE DOOR & SHELVES Take care not to damage the upper trim of the oven or the door sensor lever 1 Lift from both sides placing hands under the oven chassis 2 Push oven in, ensuring you’re not pushing on the vents or control panel 3 Secure o...
