Page 2 - Stack Two Projectors
With This Projection System You Can... Superimpose images from two stacked projectors to project a single brighter, cleaner image.Stack projection also allows projection of 3D images that can be viewed by a large audience. Stack Two Projectors 2
Page 3 - This system comes equipped with a function that allows you; Easily Superimpose Two Images
in L - out - R You may not need an HDMI splitter if your 3D compatible device is equipped with 2 HDMI outputs. This system comes equipped with a function that allows you to easily superimpose two images.See "Projecting Images" on page 14 for more information on superimposing images. Project ...
Page 5 - Part Names and Functions; from the commander’s control panel.
Part Names and Functions (Front/Top) When two projectors are assembled in a stacked configuration, the projector on top is called the “Commander”, and the projector on the bottom is called the “Receiver.” When suspended from a ceiling, the projector on top is the receiver, and the projector on the b...
Page 6 - Use the supplied USB cable to link the commander and the receiver.; Rear
Part Names and Functions (Rear/Base) Use the supplied USB cable to link the commander and the receiver. 1 Audio-L/R port 5 USB Type A port 9 Computer1 port 13 Rear adjustable feet 2 Video port 6 USB Type B port 10 Monitor Out/Computer2 port 14 Ceiling mount attachment points (three points) 3 S-Video...
Page 7 - Setup and Installation; Connecting
Setup and Installation You need the optional ceiling mount (part number ELPMBPJF) when suspending the projectors from a ceiling. See the User's Guide supplied with the ceiling mount for more information on attaching and installing the ceiling mount. This guide explains the following connection metho...
Page 8 - Use the stacking; Setting Up; Warning
Turn over the commander and the receiver, and then attach the polarizing filters. Press until they click into place. Attach the front foot and the rear feet to the base of the receiver. Turn the feet to extend and retract to adjust the horizontal tilt. Carefully remove the protective tape from the s...
Page 9 - Caution
Place the screws into the holes, and then tighten them securely (on both the left and right sides). Then tighten the commander's stacking mount screws as well. Attach the commander to the receiver by sliding the commander’s stacking mount screws into the slots in the receiver’s stacking mount. Then ...
Page 10 - You need to connect; Plug in the power cables for the commander and the
10 10 10 10 10 Connecting the commander and the receiver You need to connect a USB cable to link the commander and the receiver. Connecting Equipment Commander Commander Receiver Receiver USB cable Power cable Power cable Power inlet Power inlet 1 Plug in the power cables for the commander and the r...
Page 11 - First, check that the commander and the; Connecting with
11 11 11 11 11 1 Connect the splitter to the computer with a VGA cable. 2 Connect the commander and the receiver to the splitter with VGA cables. 3 Connect the commander or receiver to the computer with an audio cable. Audio is output from the connected projector. First, check that the commander and...
Page 12 - Connecting with HDMI
12 12 12 12 12 1 Connect the splitter to the computer with an HDMI cable. 2 Connect the commander and the receiver to the splitter with HDMI cables. You can send the computer's audio with the projected image. First, check that the commander and the receiver are properly connected with the USB cable....
Page 14 - Perform this procedure; Superimpose the images.; Superimposing Images
Superimposing the images from the commander and the receiver Perform this procedure after setting up the projectors. Projecting Images Press the [ ] button on the commander's control panel. The commander and the receiver turn on. Hold down the [Screen Fit] button for about five seconds. The initial ...
Page 18 - Screen Size and Projection Distance; Range for superimposing two images
18 Screen Size and Projection Distance 16:10 Screen Size 1 2 4 Minimum to Maximum 80” 97”-106” (248-270 cm) 3.8” (10 cm) 4 90” 110”-120” (279-304 cm) 4.3” (11 cm) 100” 122”-133” (310-338 cm) 4.7” (12 cm) 3 110” 134”-147” (341-372 cm) 5.2” (13 cm) 120” 147”-160” (373-407 cm) 5.7” (14 cm) 2 130” 159”-...
Page 19 - About the LED Indicators; Indicator status during normal operation; Indicator status during an error/warning
19 About the LED Indicators Indicator status during normal operation Orange Standby Press to start projection. Green Warm-up in progress is unavailable for about 30 seconds. Green Projection in progress The projector is operating normally. Indicator status during an error/warning RedRedRed Internal ...
Page 20 - Troubleshooting; You see a; Screen Fit has not been executed completely; message while you are trying to start the Screen Fit process.; Make sure the USB cable is properly connected.; Where to get help; Manual; Visit; Registration
20 Troubleshooting You can’t get the adjustment screen with the white and green frames to display. Make sure you press and hold the [Screen Fit] button for at least 5 seconds. Do not release the [Screen Fit] button until you see the frames. You see a Screen Fit has not been executed completely messa...
Page 21 - Notices; Declaration of Conformity; FCC Compliance Statement (PowerLite W16SK single configuration); For United States Users
21 Notices Declaration of Conformity According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Epson America, Inc. Located at: 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806 Tel: 562-981-3840 De...
Page 22 - • Consult the dealer or an experienced radio/TV technician for help.; WARNING; This Class B digital apparatus complies with Canadian ICES-003.
22 22 • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certific...
Page 23 - Copyright Notice
23 THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY...
Page 24 - être vues par un large public.; Empiler deux projecteurs
Avec ce projecteur vous pouvez... Superposer des images de deux projecteurs différents pour les fusionner en une seule image plus nette et plus lumineuse.La projection empilée permet aussi de projeter des images 3D qui peuvent être vues par un large public. Empiler deux projecteurs 24
Page 25 - Cet appareil est équipé d’une fonction qui vous permet de; D ou des jeux vidéo 3D; Superposer facilement deux images
in L - out - R Il est possible que vous n’ayez pas besoin d’un répartiteur HDMI si votre appareil compatible 3D est muni de 2 sorties HDMI. 25 Cet appareil est équipé d’une fonction qui vous permet de superposer facilement deux images.Consultez la section « Projection d’images » à la page 36 pour pl...
Page 26 - Contenu de l’emballage
26 Contenu de l’emballage Vis M3 pour fixer les filtres polariseurs (2) Projecteur et support d’empilage (contrôleur) Projecteur et support d’empilage (récepteur) Télécommande Filtres polariseurs (2) Piles AA (pour la télécommande) Pieds réglables (3) Autocollants de marquage Autocollant de protecti...
Page 27 - Noms et fonctions des pièces; temps à partir du panneau de commande du contrôleur.
27 Noms et fonctions des pièces (avant/dessus) Lorsque deux projecteurs sont assemblés dans une configuration empilée, le projecteur sur le dessus est appelé le « contrôleur », et le projecteur du dessous est appelé le « récepteur ». Lorsqu’ils sont suspendus au plafond, le projecteur du dessus est ...
Page 28 - Dessous
28 Noms et fonctions des pièces (arrière/dessous) Utilisez le câble USB fourni pour relier le contrôleur et le récepteur. 1 Port Audio-L/R 5 Port USB Type A 9 Port Computer1 13 Pattes arrière réglables 2 Port Video 6 Port USB Type B 10 Port Monitor Out/Computer2 14 Points d’installation du support a...
Page 29 - Configuration et installation; Connexion de
29 Configuration et installation Vous avez besoin du support d’installation au plafond optionnel (numéro de produit ELPMBPJF) si vous souhaitez suspendre les projecteurs au plafond. Consultez le Guide de l’utilisateur fourni avec le support d’installation au plafond pour plus d’informations sur la f...
Page 30 - Utilisez les supports; Installation; Avertissement
Retournez le contrôleur et le récepteur et fixez les filtres polariseurs. Appuyez sur les filtres polariseurs jusqu’à ce qu’un déclic se fasse entendre. Fixez le pied avant et les pieds arrière sous le récepteur. Tournez les pieds pour les déployer ou les rétracter afin d’ajuster l’inclinaison horiz...
Page 31 - Mise en garde
Placez les vis dans les trous et serrez-les bien (sur la gauche et sur la droite). Puis, serrez aussi les vis du support d’empilage du contrôleur. Fixez le contrôleur sur le récepteur en glissant les vis du support d’empilage du contrôleur dans les fentes du support d’empilage du récepteur. Puis, se...
Page 32 - Vous devez utiliser le; Branchez les câbles d’alimentation au contrôleur et au
Connecter le contrôleur et le récepteur Vous devez utiliser le câble USB fourni pour relier le contrôleur et le récepteur. Connexion de l’équipement Contrôleur Contrôleur Récepteur Récepteur Câble USB Câble d’alimentation Entrée d’alimentation Entrée d’alimentation 1 Branchez les câbles d’alimentati...
Page 33 - Connexion avec des
1 Connectez le répartiteur à votre ordinateur à l’aide d’un câble VGA. 2 Connectez le contrôleur et le récepteur au répartiteur avec des câbles VGA. 3 Connectez le contrôleur ou le récepteur à l’ordinateur à l’aide d’un câble audio. Le son est émis du projecteur connecté. Tout d’abord, assurez-vous ...
Page 36 - Effectuez cette; Superposer les images.; Superposer des images
Superposer les images du contrôleur et du récepteur. Effectuez cette procédure après avoir installé les projecteurs. Projection d’images Appuyez sur le bouton [ ] du panneau de commande du contrôleur. Le contrôleur et le récepteur s’allument. Maintenez le bouton [Screen Fit] enfoncé pendant environ ...
Page 40 - Taille de l’écran et distance de projection; Plage de superposition de deux images
40 Taille de l’écran et distance de projection Taille de l’écran 16:10 1 2 4 Du minimum au maximum 80 po 97 po-106 po (248-270 cm) 3,8 po (10 cm) 4 90 po 110 po-120 po (279-304 cm) 4,3 po (11 cm) 100 po 122 po-133 po (310-338 cm) 4,7 po (12 cm) 3 110 po 134 po-147 po (341-372 cm) 5,2 po (13 cm) 120 ...
Page 41 - À propos des témoins DEL; État du témoin pendant le fonctionnement normal; État du témoin pendant une erreur/alerte
41 À propos des témoins DEL État du témoin pendant le fonctionnement normal Orange En veille Appuyez sur pour démarrer la projection. Vert Réchauffement en cours est indisponible pendant environ 30 secondes. Vert Projection en cours Le projecteur fonctionne normalement. État du témoin pendant une er...
Page 42 - Problèmes et solutions; Le récepteur ne s’allume pas lorsque vous allumez le contrôleur.; Comment obtenir de l’aide; Manuel; Français; Enregistrement du produit
42 Problèmes et solutions Impossible d’afficher l’écran d’ajustement avec les cadres blanc et vert. Assurez-vous de maintenir le bouton [Screen Fit] enfoncé pendant au moins 5 secondes. Ne relâchez pas le bouton [Screen Fit] avant que les cadres n’apparaissent. Un message indiquant que l’ajustement ...
Page 43 - Avis; Déclaration de conformité; Nom commercial : PowerLite W16SK; Pour les utilisateurs des États-Unis; This Class A digital apparatus complies with Canadian ICES-003.
43 Avis Déclaration de conformité Selon la norme 47CFR, parties 2 et 15 régissant, les ordinateurs personnels et périphériques de classe B, et/ou les unités centrales et les dispositifs d’alimentation électrique utilisés avec les ordinateurs personnels de classe B.Nous : Epson America, Inc. Situé au...
Page 44 - permission d’utilisation du matériel.; Pour les utilisateurs du Canada
44 44 Déclaration de conformité avec la FCC (PowerLite W16SK configuration unique) Pour les utilisateurs des États-Unis À l’issue des tests dont il a fait l’objet, cet appareil a été déclaré conforme aux normes des appareils numériques de classe B, conformément à la partie 15 de la réglementation FC...