Epson T2340/24- User Manual

Installation ➤ Unpacking the printer Please open the printer package and check that all the following items are included. If any item is missing or damaged, please contact the store wherethe product was purchased.Remove the transport protection elements as described in theunpacking instructions.The ...

➤ Connecting the printer Make sure that the unit is set to the correct voltage (i.e. 230 Vfor Europe, 120 V for the USA). Refer to the type plate besidethe power inlet on the rear side of the printer.If this is not the case, contact your dealer. Connect the power cable to the printer’s powerinlet as...

Control panel You can control printer operation using the control panel and the keys. The first line of the display informs you about whether the printer is in Online or in Offline mode and about the paper path selected ( Trac.1 or Single ). ➤ Online mode When switching on the printer, it automatica...

Installing theribbon cassette Remove any paper loaded into the printer. Before opening the cover, make sure that the printer is switched off. Set the Paper Thickness Adjustment Lever to the “8” position. Pull the Latch Levers near the right and left ends on the AccessCover to the front, and detach t...

Align the part “A” on the left side of the Ink-ribbon Cartridgeto the two hooks of the printer, push the cartridge all the wayuntil it clicks. If there is resistance, push it while turning theRibbon Feed Knob. Detach the Ribbon Guide from the Ink-ribbon Cartridge. Put the Ribbon Guide between the Pr...

When the Ink-ribbon Cartridge setting is complete, attach theAccess Cover.Set the Paper Thickness Adjustment Lever in accordance withthe thickness of the paper to be used. Refer to page 18 ( Setting the print head gap ). Loading paper Only use paper which is suitable for this printer. For more infor...

Set the Paper Type Selection Lever to Cut Sheet Paper mode.Make sure that the printer is in Single Sheet mode. For how toselect Single Sheet mode refer to page 14 ( Paper path quick selection ). Determine the left margin by moving the Left Paper Guide leftor right. (The “[A” mark indicates the stand...

➤ Printer in fanfold paper mode Set the Paper Thickness Adjustment Lever according to the typeof paper to be used. Refer to page 18 (Setting the print head gap). Set the Paper Type Selection Lever to Continuous Form FeedPaper mode.Open the Front Cover to its upright position until it snaps in.This p...

With the printing side of the paper facing up, fit the feedingholes on the left edge of the paper over the Left Tractor pins andclose the Paper Flap.Fit the feeding holes on the right edge of the paper over the RightTractor pins, and close the Paper Flap. After the paper is set, adjust the left marg...

Changing thepaper type You can change the paper type (the paper path) either using the paper path quick selection featureor via the Setup menu. ➤ Paper path quickselection First cut the fed-out portion of a Continuous Form Feed Paper at the perforated line. To do this,proceed as follows. Make sure t...

Press the Online key to make the printer ready for operation. Paper transport Loaded paper (fanfold paper/single sheets) can be transported in the printer in different ways. Make sure that the printer is in Offline status; press the Online key, if necessary. ➀ Short keypress: Line feed (LF) is initi...

Press the Adjust key. Press the TOF key. The bottom edge of the currently valid first printing line A of thepaper is transported to the tear edge B.The factory setting for the first printing position is 12/72". Press the < or > key to move the first printing line to the appropriate positio...

Settings (II) ➤ Setting the printhead gap The printer has been provided with a Paper Thickness Adjustment Lever for adjusting the printhead gap To obtain optimum print quality, the gap between the Print Headand the Platen needs to be adjusted according to the thicknessof the paper to be used. The fo...

➤ Changing paper inSetup mode ➤ From fanfold paperto single sheet mode When fanfold paper was in use and you want to change over to single sheet mode, proceed asdescribed below. You do not need to remove the fanfold paper. Cut the fed-out portion of the Continuous Form Feed Paper at the perforated l...

Set the Paper Type Selection Lever to Cut Sheet Paper mode. In the display appears… Stand the Paper Tray up and pull up the Paper Extension Trays (see page 10).Place a sheet of paper aligned to the Left Paper Guide, and adjust the Right PaperGuide to the right edge of the paper.Insert the paper betw...

Confirm the setting by pressing the Set key. An acoustic signal acknowledges the input. The display toggles between… and… Shift the Paper Type Selection Lever to the position needed.The printer is now ready for printing fanfold paper.Press the Online key to make the printer ready for operation. ➤ Se...

The selection made will not be retained after printer power-off. For information on how to se-lect a font permanently, refer to online documentation on the CD-ROM, chapter 1 ( Menu description table). ➤ Setting thecharacter pitch You can use the CPI key to set the character pitch in Setup mode. Pres...

Specifications ➤ Printer specifications ENGLISH Quick start-up Specifications 23 ➤ Paper specifications Printing method serial printing with 9-pin matrix print head serial printing with 24-pin matrix print head Print width narrow printer 80 characters at 10 cpi wide printer 136 characters at 10 cpi ...

Accessories Quick start-up 24 For more information on printer specifications and paper specifications, refer to the online documentation on the CD-ROM. Accessories Ribbon cassettes Narrow printer: Part No. 044 829Wide printer: Part No. 044 830 Demo page The demo page contains information on the firm...

TALLY REPRESENTATIVES GERMANYTally Computerdrucker GmbHPostfach 2969D-89019 UlmDeutschlandTel.: +49 7308 80 0Fax: +49 7308 5903http://www.Tally.de ITALYTally S.R.L.Via Borsini 6I-20094 Corsico (MI)ItaliaTel.: +39 02 48608 1Fax: +39 02 48601 141http://www.Tally.it SPAINTally SRLJoaquin Lorenzo 4, Loc...