Epson PowerLite Pro Cinema LS9600e- User Manual

Quick Setup

Before using the projector, make sure you read the safety instructions in the
online User’s Guide.

Choose a location

Keep the projector level and place it at a height so its lens is even with the top
or bottom of the screen and is centered horizontally. If this isn’t possible, use
the lens shift feature or the keystone correction button on the projector to
reposition the image (see “Adjust the image”).

In order to view 3D images correctly, RF 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):

See the online User’s Guide for more information on where to place your
projector.

Connect the projector

Choose from the following connections. For additional connection types, see
the online User’s Guide.

Video device

1

Loosen the two screws at the bottom of the cable cover, then pull the
cover forward.

2

Lift the cable cover out of the grooves at the top.

3

Connect up to 4 video devices and use the Source

buttons on the remote

control or the

button on the projector to switch between them.

Component video cable

RCA video cable

HDMI cable

WirelessHD Transmitter

Follow these steps to set up the included WirelessHD Transmitter.

HDMI

1

Place the transmitter within 32 feet (10 m) of the projector. Make sure the
front of the transmitter faces the front of the projector. See the online
User’s Guide for more information on the WirelessHD transmission range.

Note:

Do not place the transmitter on a metal surface, as this may

interfere with the signal. Make sure there are no obstructions between
the transmitter and the projector.

2

Plug the AC adapter into the transmitter and a wall outlet.

3

Connect the HDMI cables to your video input devices and the HDMI ports
on the side and back of the WirelessHD Transmitter. You can connect up
to five input devices to the transmitter. See “Viewing WirelessHD content”
for information on switching between input sources

Note:

You can connect tablets, smartphones and other devices that

support the MHL™ standard to the HDMI port on the side of the
WirelessHD Transmitter. Devices that use an MHL connection include
the Samsung™ Galaxy Note™ II and the Roku

®

Streaming Stick™. Some

devices may require an adapter or may not require an MHL cable.
Not all features or functions may be supported. Check your device’s
documentation for more information.

4

To use the transmitter as a pass-through device to a television or other
display, connect an HDMI cable to the display device and the HDMI output
port on the rear of the transmitter. See “Viewing WirelessHD content” for
information on switching between wireless and wired display modes.

Turn on your equipment

1

Turn on your video source.

2

Plug in the projector.

3

Press the

power button on the projector or the

On

button on the

remote control. The shutter opens and the power

light flashes blue,

then stays on.

Note:

To shut down the projector, press the

power button on the

projector or the Standby button on the remote control, then unplug it.
You don’t have to wait for the projector to cool down.

4

The default language of the menu system is English. To select another
language, press the

Menu

button on the projector or remote control.

Select

Settings

and press

Enter

. Select

Language

and press

Enter

. Select

your language and press

Enter

. Press the

Menu

button to exit the menu

system.

Using the remote control

Make sure the batteries are installed as shown (two AA batteries).

Choose which source

to display

Turn projector on

Access projector

menus

Adjust zoom, focus

and lens shift

Turn off projector

display

Navigate projector

menus

Control WirelessHD

functions

Turn projector off

Switch between

2D and 3D

Control connected

sources with

HDMI Link

For more information on using the remote control, see the online
User’s Guide.

Adjust the image

1

Press the

Pattern

button on the remote control to display a test pattern.

2

To raise the image or correct a tilted image, adjust the front feet as
shown below.

3

Press the

Lens

button on the remote control and use the and

buttons to focus the image.

4

Press the

Lens

button on the remote control again and use the and

buttons to reduce or enlarge the image.

5

Press the

Lens

button on the remote control again and use the , ,

and buttons to reposition the image.

6

If your image looks like

or

, you can use the button to correct

this.

Note:

Using the keystone adjustment can affect the size and effective

resolution of your image. If possible, change the position of your
projector to eliminate the keystone effect and use the lens shift option
to position the image as necessary.

PowerLite

®

Pro Cinema LS9600e

*412630400*

*412630400*