Page 2 - C o n t e n t s; Contents
C o n t e n t s | 1 Contents Unpacking and assembling the printer .............................................................................................. 2 Assembling the stand .................................................................................................................. 5...
Page 3 - U n p a c k i n g a n d a s s e m b l i n g t h e p r i n t e r; Unpacking and assembling the printer; Follow these steps to assemble your printer and its stand.
2 | U n p a c k i n g a n d a s s e m b l i n g t h e p r i n t e r Unpacking and assembling the printer Note: Unless otherwise indicated, the illustrations in this guide show the SureColor ® P8000/P9000, but the instructions apply to all models. Follow these steps to assemble your printer and its s...
Page 4 - The following items are included with your printer:
U n p a c k i n g a n d a s s e m b l i n g t h e p r i n t e r | 3 You need additional floor space to assemble the printer and stand, so be sure to prepare a large, empty area before unpacking them. For assembly, you need floor space of approximately: • 8 × 8 feet (2.4 × 2.4 m) for the SC-P6000/SC-...
Page 6 - A s s e m b l i n g t h e s t a n d; Assembling the stand; Make sure you have all of these items:
A s s e m b l i n g t h e s t a n d | 5 Assembling the stand 1. Make sure you have all of these items: 2. Insert the strut into the left side of the stand. (The sides of the stand are labeled L and R. ) 2 sides Horizontal strut Hex wrench 6 bolts
Page 7 - Insert the strut into the right side and fasten it with 3 bolts.
6 | A s s e m b l i n g t h e s t a n d 3. Fasten the strut with 3 bolts. Use the hex wrench to tighten the bolts. 4. Insert the strut into the right side and fasten it with 3 bolts. Note: Make sure you tighten all bolts before moving to the next step.
Page 8 - M o u n t i n g t h e p r i n t e r o n t h e s t a n d; Mounting the printer on the stand; Make sure you have these items:
M o u n t i n g t h e p r i n t e r o n t h e s t a n d | 7 5. Lock the casters. Mounting the printer on the stand 1. Make sure you have these items: 2. Remove the cardboard panels and other printer packing materials. Printer 2 wing screws withlock washers
Page 9 - M o u n t i n g t h e p r i n t e r o n t h e s t a n d; Insert the printer to the stand with the wing screws and washers.
8 | M o u n t i n g t h e p r i n t e r o n t h e s t a n d 3. Lift the printer and mount it on the stand, aligning the pegs with the holes on the bottom of the printer. WARNING: Four or more people are required to lift the printer. 4. Insert the printer to the stand with the wing screws and washers...
Page 15 - Insert the rod into the fabric channel.
14 | A t t a c h i n g t h e p a p e r b a s k e t ( S C - P 6 0 0 0 / S C - P 7 0 0 0 ) 11. Insert the rod into the fabric channel. 12. Insert the free ends of the rod into the holes in the sides of the stand.
Page 24 - Loop the tabs over the rod
A t t a c h i n g t h e p a p e r b a s k e t ( S C - P 8 0 0 0 / S C - P 9 0 0 0 ) | 23 15. Insert the free ends of the rod into the holes in the sides of the stand. 16. Loop the tabs over the rod
Page 25 - I n s t a l l i n g t h e o p t i o n a l i n t e r n a l p r i n t s e r v e r; Attach the paper guides to the bottom of the printer.; Installing the optional internal print server
24 | I n s t a l l i n g t h e o p t i o n a l i n t e r n a l p r i n t s e r v e r 17. Attach the paper guides to the bottom of the printer. Installing the optional internal print server If you purchased the optional internal print server (part number C12C848031), follow these steps to install it ...
Page 26 - I n s t a l l i n g t h e o p t i o n a l i n t e r n a l p r i n t s e r v e r; Insert the internal print server into the slot.
I n s t a l l i n g t h e o p t i o n a l i n t e r n a l p r i n t s e r v e r | 25 2. Remove the two screws securing the option slot cover to the back of the printer, then remove the cover. Note: Make sure you save the option slot cover. Remove the internal print server and re-attach the cover if ...
Page 27 - C o m p l e t i n g s e t u p a n d c o n n e c t i n g t h e p o w e r c o r d; Secure the internal print server using the screws you removed.; Completing setup and connecting the power cord; Setup
26 | C o m p l e t i n g s e t u p a n d c o n n e c t i n g t h e p o w e r c o r d 4. Secure the internal print server using the screws you removed. Completing setup and connecting the power cord 1. Attach the manual holder to the left or right side of the stand. Store this Setup guide and the Qui...
Page 28 - C o m p l e t i n g s e t u p a n d c o n n e c t i n g t h e p o w e r c o r d; Remove any packing tape and plastic film. Check these areas:
C o m p l e t i n g s e t u p a n d c o n n e c t i n g t h e p o w e r c o r d | 27 3. Remove any packing tape and plastic film. Check these areas: • the front cover • the ink compartment covers • the maintenance tank(s) 4. Open the roll paper cover and remove the tape and packing material.
Page 29 - Open the front cover and remove the tape and packing material.; Close the front cover.
28 | C o m p l e t i n g s e t u p a n d c o n n e c t i n g t h e p o w e r c o r d 5. Open the front cover and remove the tape and packing material. Note: Save the packing material in case you need to ship the printer. 6. Close the front cover. 7. Connect the power cord to the AC inlet on the back...
Page 30 - I n s t a l l i n g i n k; Plug the power cord into a properly grounded electrical outlet.; Installing ink
I n s t a l l i n g i n k | 29 8. Attach the cable guides to the left or right side of the printer back and route the power cord to the side of the printer as shown. 9. For the SC-P8000/SC-P9000, attach the loops on the paper basket cords to the cable guides. 10. Plug the power cord into a properly ...
Page 31 - Press the; Open both ink covers.
30 | I n s t a l l i n g i n k The cartridges shipped with your printer are provided mainly to charge the ink system. Make sure you order a new set of cartridges as soon as possible. 1. Press the P power button to turn on the printer. 2. Select the language, date/time, and units of measurment for th...
Page 33 - power; After ink charging is complete, you need to load paper before; Ready; appears on the display.
32 | I n s t a l l i n g i n k Hold each cartridge with the arrow pointing toward the printer, then insert it into its slot until it clicks into place. Make sure you insert each cartridge all the way into the correct slot. 6. After installing all of the cartridges, close the ink covers. The printer ...
Page 34 - L o a d i n g r o l l p a p e r; Loading roll paper; Placing roll paper in the printer; Open the roll paper cover.
L o a d i n g r o l l p a p e r | 33 Loading roll paper You can use roll paper with a 2- or 3-inch core and a width of up to 24 inches (61 cm) for the SC-P6000/SC-P7000, or 44 inches (112 cm) for the SC-P8000/SC-P9000. Placing roll paper in the printer 1. Open the roll paper cover.
Page 35 - P l a c i n g r o l l p a p e r i n t h e p r i n t e r; Place the roll on top of the printer.
34 | P l a c i n g r o l l p a p e r i n t h e p r i n t e r 2. Push the lock lever down firmly, then move the roll paper holder to the left. Note: Make sure you push the lock lever all the way down. If the lever is raised at all, the lock is still on. 3. Place the roll on top of the printer.
Page 36 - P l a c i n g r o l l p a p e r i n t h e p r i n t e r; Release the tension lever on both adapters.
P l a c i n g r o l l p a p e r i n t h e p r i n t e r | 35 4. If necessary, adjust the roll media adapters to fit the core size of the roll paper. 2-inch core: 3-inch core: 5. Release the tension lever on both adapters.
Page 38 - Slide the roll paper holder to align the left adapter with the
P l a c i n g r o l l p a p e r i n t h e p r i n t e r | 37 8. Slide the roll paper holder to align the left adapter with the u on the holder. 9. Roll the paper slowly into position.
Page 39 - Pull up the lock lever to lock the paper in place.
38 | P l a c i n g r o l l p a p e r i n t h e p r i n t e r 10. Slide the roll paper holder to the right to secure it in the printer. Make sure both ends of the roll paper are secured in the adapters. 11. Pull up the lock lever to lock the paper in place. 12. If the light is not on, press the butto...
Page 40 - L o a d i n g r o l l p a p e r f o r p r i n t i n g; Loading roll paper for printing; Paper Feed
L o a d i n g r o l l p a p e r f o r p r i n t i n g | 39 Loading roll paper for printing 1. Insert the paper into the slot and pull it down until the edge of the paper is in the center of the stand. If the paper doesn’t come out, you may need to decrease the suction by pressing the d Paper Feed bu...
Page 41 - A l i g n i n g t h e p r i n t h e a d; Aligning the print head
40 | A l i g n i n g t h e p r i n t h e a d 5. On the screen that appears on the LCD screen, select Keep Settings Above if the paper settings are correct, or select Change Settings , then adjust the settings. 6. Press OK . To avoid indenting or creasing the paper, remove it from the paper path and ...
Page 42 - C o n n e c t i n g t o y o u r s y s t e m; Connecting to your system; You can use a USB and/or an Ethernet network connection.
C o n n e c t i n g t o y o u r s y s t e m | 41 Connecting to your system You can use a USB and/or an Ethernet network connection. For a USB connection, make sure your system has the appropriate port and you have a standard, shielded cable 10 feet (6 m) long or less. To connect to a network hub, yo...
Page 43 - I n s t a l l i n g t h e s o f t w a r e; Installing the software; Checking the current firmware version
42 | I n s t a l l i n g t h e s o f t w a r e Installing the software Download and run your product’s software package: • www.epson.com/support/p6000 (U.S.) or www.epson.ca/support/p6000 (Canada) • www.epson.com/support/p7000 (U.S.) or www.epson.ca/support/p7000 (Canada) • www.epson.com/support/p80...
Page 44 - C o n f i g u r i n g t h e p r i n t e r f o r y o u r n e t w o r k; Configuring the printer for your network
C o n f i g u r i n g t h e p r i n t e r f o r y o u r n e t w o r k | 43 3. Click Acquire Latest Information to automatically download the latest firmware version for your printer from the internet. If there is a firmware update, the message “Found the latest firmware information. Do you want to d...
Page 45 - C o n f i g u r i n g t h e p r i n t e r f o r y o u r n e t w o r k
44 | C o n f i g u r i n g t h e p r i n t e r f o r y o u r n e t w o r k EPSON and SureColor are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. General Notice: Other product names used herein are for identification purposes only and may be ...
Page 46 - Epson
Setup CPD-50156 Printed in USA Epson ® SureColor ® P-Series P6000/P7000/P8000/P9000 CPD50156_SureColor P6000-P9000_Setup_E.indd 1 8/19/15 4:04 PM