Epson DR-EPS19- Manual
Epson DR-EPS19– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – SmartPanel Projector Driver Application Note; III. Additional Projector Information; Projector Firmware Note; must be set to; Special Control
- Page 3 – Projector Driver Application Note; Revision D; I. PROJECTOR CONTROL
- Page 4 – Enter and ESC; Configuration; can be used to customize these settings; Power Status Feedback Method; strongly recommends; wiring the IR emitter. See
- Page 5 – PROJECTOR CONTROL; Control; IR Emitter; Section III
- Page 6 – STARTUP SCREEN should be set to OFF in the ADVANCED1 Menu.; III. PROJECTOR FIRMWARE NOTE; HELP
- Page 7 – VI. REVISION HISTORY
Quick Start Reference Sheet
Epson EMP-7800
Revision D
DR-EPS19 – 3/29/04
SP Controls reserves the right to modify specifications without notice at any time.
NOTE:
This document is intended
only as a quick reference for installation
– please read the SP
Controls Application Note for a complete description of this projector driver prior to installation.
I. Driver Features
1. Input Selection Mapping
Selection 1:
VIDEO (RCA)
Selection 2:
S-VIDEO
Selection 3:
YPbPr (BNC)
Selection 4:
COMPUTER (VGA)
2. Hidden Function Mapping (Default Configuration)
Using the ON button as a shift key, press the following buttons to access the specified projector features.
Selection 1:
ESC
Selection 2:
ENTER
Selection 3:
ADJUST LEFT
Selection 4:
ADJUST RIGHT
Off:
MENU
Volume Up:
ADJUST UP
Volume Down:
ADJUST DOWN
3. Other Driver Features
Power Status Feedback Method
RS-232 Power Polling
Control Wiring:
RS-232 Only
II. Wiring Specifications
Although this driver does not use IR, SP Controls strongly recommends wiring for RS-232 and IR. Under
certain conditions it may be necessary to control this projector through IR – see the
Special Control Note
in the Application Note below for more information.
NOTE: For a wiring diagram, please see the SP Controls Application Note.
Wire the Panel RS-232 port to a female DB9 as follows:
TX to 2
RX to 3
GND to 5
Connect this female DB9 to the projector port labeled
CONTROL (RS-232C)
.
Wire the Panel IR/Serial port to a female 1/8" Mini as follows:
IR/SER
to
tip
GND
to
ring
Connect to the included IR Emitter and attach the emitter bud to
the rear projector IR window
. Note
that
the projector
does not consistently respond
when the IR emitter is attached to the front IR window.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Epson DR-EPS19
Summary
SmartPanel Projector Driver Application Note Epson EMP-7800 © 2004 SP Controls Inc. 601 Minnesota Suite 115, San Francisco, CA 94107 [email protected] III. Additional Projector Information NOTE: For use with this driver, the Epson EMP-7800 should be running projector firmware version 2.05 or highe...
Projector Driver Application Note Epson EMP-7800 Revision D DR-EPS19 – 3/29/04 SP Controls reserves the right to modify specifications without notice at any time. This document describes the SmartPanel Projector Driver for the Epson EMP-7800 projector. For more information on configuring and using t...
SmartPanel Projector Driver Application Note Epson EMP-7800 © 2004 SP Controls Inc. 601 Minnesota Suite 115, San Francisco, CA 94107 [email protected] Hidden functions are accessed by pressing the indicated key while the holding the On key down. Hidden functions names are based on the Epson remote...
