Page 3 - Engli; Safety Precautions; Precaution Headings
1 Engli s h Safety Precautions This document presents important information intended to ensure safe and effective use of this product. Please read this document carefully, and store it in an accessible location near your installation. Precaution Headings This document uses the two headings shown bel...
Page 4 - The display conforms to the following Directies and Norms
2 CAUTION: ❏ Do not plug the cable differently from the instruction in this manual. Wrong connection may cause equipment damage and fire. ❏ Be sure to set this equipment on a firm, stable, horizontal surface. Product may be damaged or cause injury if it falls. ❏ Do not use in locations subject to hi...
Page 5 - WARNING; This Class A digital apparatus complies with Canadian ICES-003.; About This Manual; Cautions and Notes
3 Engli s h WARNING You are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could void your authority to operate the equipment. FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a Class A digit...
Page 6 - Contents
4 Contents About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Unpacking . . . . ...
Page 7 - This manual explains how to set up the DM-D500.; Unpacking; The following items are in the box.; Cautions on Handling; When you use the DM-D500, be sure to note the following points:
5 Engli s h This manual explains how to set up the DM-D500. Unpacking The following items are in the box. Make sure that you have all the items shown above, and that none has been damaged. If you find anything missing or damaged items, please contact your DM-D500 dealer. Cautions on Handling When yo...
Page 8 - Usage; The DM-D500 can be used with the following equiment.; IR Series; . You can attach the DM-D500 to the IR Series using the; Other TM printers
6 Usage The DM-D500 can be used with the following equiment. ❏ IR Series . You can attach the DM-D500 to the IR Series using the “DM-D pole unit for IR” (DP-504). (See page 8.) ❏ TM-H5000II/TM-J8000 printers . You can attach the DM-D500 to TM-H5000II/TM-J8000 printers using the “DM-D pole unit for T...
Page 9 - Precautions when connecting to a TM printer; Printer
7 Engli s h Precautions when connecting to a TM printer When the DM-D500 is connected to a TM printer, be sure to check the serial number on the label affixed to the rear or bottom of the TM printer. If the serial number is one of the numbers indicated below it can be used immediately. If the serial...
Page 10 - Assembling; Attaching to the IR Series; Required items
8 Assembling Attaching to the IR Series The DM-D500 can be attached directly to the IR Series using the “DM-D pole unit for IR” (DP-504). Required items The following items are used to attach the DM-D500 to the IR Series. These items are packed with the “DM-D pole unit for IR” (DP-504). Assembling s...
Page 13 - Assembling steps
11 Engli s h Assembling steps 1. Pass the cable for the DM-D500 through support C, and attach support C to the DM-D500. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 2. Attach the base to the setting position on the TM printer and...
Page 14 - Connect the cable for the DM-D500 to the DM connector on the TM
12 3. Pass the cable for the DM-D500 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click. 5. Connect the cable for the DM-D500 to the DM connector on the TM printer.
Page 17 - Pass the cable for the DM-D500 through the hole on fixing plate A,
15 Engli s h 3. Pass the cable for the DM-D500 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 4. Connect the cable for the DM-D500 to the DM connector on the TM printer. 5. Adjust the length of the cable and secure fixing plate A to the printer with screws. [TM-U...
Page 21 - The horizontal rotation mechanism of fixing plate A can be
19 Engli s h 7. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw.
Page 23 - Attaching to Other TM Printers
21 Engli s h Attaching to Other TM Printers When using with other TM printers, the DM-D500 can be attached to a desk or other surface, using the “DM-D pole unit for TM printers (Type A)” (DP-502), and Velcro tapes or screws. Required items The following items are used when the DM-D500 is used with o...
Page 25 - Store any excess cable in the support, and attach the DM-D500
23 Engli s h 5. Store any excess cable in the support, and attach the DM-D500 to fixing plate A. 6. Peel off the Velcro tapes, and attach the display to the setting position. Assembling steps using screws 1. Follow steps 2 and 3 in “Assembling steps using Velcro tapes.” 2. Secure fixing plate A to t...
Page 26 - Attaching to the DM-D stand
24 Attaching to the DM-D stand The DM-D500 can be attached directly to the DM-D stand using the “DM-D stand unit for DM-D 500” (DP-501). The DM-D500 with the DM-D stand can be connected to a TM printer, or be used as a stand alone product. Required items The following items are used to attach the DM...
Page 27 - Connectors for the DM-D stand
25 Engli s h Connectors for the DM-D stand The connectors for the DM-D stand are as follows: Note: The DM-D stand comes with inch-type hexagonal lock screws installed to secure the interface cable to the interface connector for RS-232. If you plan to use an interface cable which requires millimeter-...
Page 30 - Connect one end of the computer interface cable to the computer
28 4. Connect one end of the computer interface cable to the computer connector on the DM-D stand; then connect the other end to the RS-232 connector on the computer. Tighten the screws on both ends of the cables to fasten them. 5. When using as a stand alone, go to step 6. When using with the print...
Page 31 - When not using the extension cable for power supply packed with
29 Engli s h 6. When not using the extension cable for power supply packed with the DM-D stand, go to step 7. When using the extension cable, connect it (with the arrow mark up) to the extension cable connector indicated with “POWER OUT” on the DM-D stand; then connect the other end to the power con...
Page 33 - Part Names and Functions; Exterior
31 Engli s h Part Names and Functions Exterior ❏ Display: Characters are displayed. ❏ Power switch: The power is turned on/off. ❏ DIP switch: The functions of the DM-D500 are changed. (See “DIP switch” for details.) Note: When turning on the DM-D500 again after turning it off, wait for at least 3 se...
Page 34 - DIP Switch; DIP Switch Functions; The DM-D500 has two groups of DIP switches.
32 DIP Switch DIP Switch Functions The DM-D500 has two groups of DIP switches. The functions of the DIP switches are as follows: DIP switch 1 (*1)XON/XOFF is effective only when the DM-D500 is connected with a stand alone. Transmission speed *Cannot be set to 57,600 or 115,200 when using the IR Seri...
Page 35 - DIP switch 2
33 Engli s h DIP switch 2 (*1)The “Y-connection enable” is set when a TM printer with no modular jack for the DM-D is connected with this product, using one COM port to connect both TM printer and DM display. In this case, an optional DM-D stand (DP-501) and a connecting cable are required. In the c...
Page 37 - Turning and Tilting the DM-D5 0 0; The display area has the following range of movement:
35 Engli s h Turning and Tilting the DM-D5 0 0 You can turn or tilt the display while holding the support. The display can be moved easily, so do not move any further if it stops. If you move it by force, you may damage it. With the “DM-D pole unit for IR” (DP-504) and the “DM-D pole unit for TM pri...
Page 38 - Self Test; Check Items of Self test
36 Self Test The DM-D500 has a self test function. If you want to perform a self test, you must change the setting of the DIP switch. Check Items of Self test The following items are checked during the self test: ❏ Control ROM version ❏ DIP switch settings ❏ Example of display characters ❏ Example o...
Page 39 - Specification; General Specifications
37 Engli s h Specification General Specifications ❏ Height, Width, Depth and Weight • DM-D500: Height: 83 mm Width: 213 mm Depth: 51 mm Weight: 460 g • DM-D stand (DP-501): Height: 65 mm Width: 200 mm Depth: 118 mm Weight: 440 g 213 mm 83 mm 65 mm 51 mm 118 mm 200 mm 90 ° 48 ° DM-D500 DM-D stand (DP...
Page 41 - Electrical Specifications
39 Engli s h ❏ Tilt angle Max 48 ° (4 steps, 5 positions) ❏ Horizontal rotation Max 90 ° (for each left and right at 45 ° ) ❏ Vacuum fluorescent display • Total number of dots: 256 (W) × 64 (H) dots • Dot pitch: 0.55 × 0.55 mm • Number of characters: 32 column × 4 lines max. (When using Font A) • Nu...
