Page 3 - Safety Precautions; Precaution Headings
1 Eng li s h Safety Precautions This document presents important information intended to ensure safe and effective use of this product. Please read this document carefully, and store it in an accessible location near your installation. Precaution Headings This document uses the two headings shown be...
Page 4 - The display conforms to the following Directies and Norms
2 CAUTION: ❏ Do not plug the cable differently from the instruction in this manual. Wrong connection may cause equipment damage and fire. ❏ Be sure to set this equipment on a firm, stable, horizontal surface. Product may be damaged or cause injury if it falls. ❏ Do not use in locations subject to hi...
Page 5 - WARNING; This Class A digital apparatus complies with Canadian ICES-003.; About This Manual; Cautions and Notes
3 Eng li s h WARNING You are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could void your authority to operate the equipment. FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a Class A digi...
Page 6 - Contents
4 Contents About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unpacking . . . ....
Page 7 - This manual explains how to set up the DM-D210.; Unpacking; The following items are in the box.; Cautions on Handling; When you use the DM-D210, be sure to note the following points:
5 Eng li s h This manual explains how to set up the DM-D210. Unpacking The following items are in the box. Make sure that you have all the items shown above, and that none has been damaged. If you find anything missing or damaged items, please contact your DM-D210 dealer. Cautions on Handling When y...
Page 8 - Usage; The DM-D210 can be used with the following equiment.; IR series; . You can attach the DM-D210 to the IR series using the; Other TM printers
6 Usage The DM-D210 can be used with the following equiment. ❏ IR series . You can attach the DM-D210 to the IR series using the “DM-D pole unit for IR” (DP-504). (See page 7.) ❏ TM-H5000II/TM-J8000 printers . You can attach the DM-D210 to TM-H5000II/TM-J8000 printers using the “DM-D pole unit for T...
Page 9 - Assembling; Attaching to the IR series; Required items; Pass the cable for the DM-D210 through support A, and attach
7 Eng li s h Assembling Attaching to the IR series The DM-D210 can be attached directly to the IR series using the “DM-D pole unit for IR” (DP-504). Required items The following items are used to attach the DM-D210 to the IR series. These items are packed with the “DM-D pole unit for IR” (DP-504). A...
Page 11 - Connect the cable for the DM-D210 to the DM connector on the IR
9 Eng li s h 5. Connect the cable for the DM-D210 to the DM connector on the IR series. Attaching to the TM-H5000II/TM-J8000 The DM-D210 can be attached directly to the TM-H5000II/TM-J8000 printers using the “DM-D pole unit for TM printers (Type B)” (DP-503). Required items The following items are u...
Page 12 - Assembling steps; Pass the cable for the DM-D210 through support C, and attach
10 Assembling steps 1. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 2. Attach the base to the setting position on the TM printer and secure it...
Page 13 - Connect the cable for the DM-D210 to the DM connector on the TM
11 Eng li s h 3. Pass the cable for the DM-D210 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click. 5. Connect the cable for the DM-D210 to the DM connector on the TM printer.
Page 17 - Store any excess cable in the support, and attach the DM-D210 to
15 Eng li s h 6. Store any excess cable in the support, and attach the DM-D210 to fixing plate A. Attaching to the TM-H6000/TM-U675 The DM-D210 can be attached directly to the TM-H6000/TM-U675 printers using the “DM-D pole unit for TM printers (Type A)” (DP-502). You can attach fixing plate A on eit...
Page 19 - Pass the cable for the DM-D210 through the hole on fixing plate A,
17 Eng li s h 4. Pass the cable for the DM-D210 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 5. Connect the cable for the DM-D210 to the DM connector on the TM printer. 6. Attach fixing plate A to the TM printer using the stopper. When you attach the stopper, i...
Page 20 - The horizontal rotation mechanism of fixing plate A can be
18 7. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw.
Page 21 - Store any excess cable in the support and attach the DM-D210 to
19 Eng li s h Note: The paper roll cover may not open if the position of the display is inappropriate. Before securing the position of the display, make sure that you can open the paper roll cover. 8. Store any excess cable in the support and attach the DM-D210 to fixing plate A. 9. Connect the powe...
Page 22 - Attaching to Other TM Printers; Attach Velcro tapes to the bottom of fixing plate A.
20 Attaching to Other TM Printers When using with other TM printers, the DM-D210 can be attached to a desk or other surface, using the “DM-D pole unit for TM printers (Type A)” (DP-502), and Velcro tapes or screws. Required items The following items are used when the DM-D210 is used with other TM pr...
Page 23 - Pass the cable for the DM-D210 through support C, and attach
21 Eng li s h 2. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 3. Pass the cable for the DM-D210 through the hole on fixing plate A, and fix th...
Page 24 - Assembling steps using screws; Follow steps 2 and 3 in “Assembling steps using Velcro tapes.”
22 5. Store any excess cable in the support, and attach the DM-D210 to fixing plate A. 6. Peel off the Velcro tapes, and attach the display to the setting position. Assembling steps using screws 1. Follow steps 2 and 3 in “Assembling steps using Velcro tapes.” 2. Secure fixing plate A to the setting...
Page 25 - Attaching to the DM-D stand
23 Eng li s h Attaching to the DM-D stand The DM-D210 can be attached directly to the DM-D stand using the “DM-D stand unit for DM Customer Display ” (DP-210). The DM-D210 with the DM-D stand can be connected to a TM printer, or be used as a stand alone product. Required items The following items ar...
Page 26 - Connectors for the DM-D stand; The connectors for the DM-D stand are as follows:
24 Connectors for the DM-D stand The connectors for the DM-D stand are as follows: Note: The DM-D stand comes with inch-type hexagonal lock screws installed to secure the interface cable to the interface connector for RS-232. If you plan to use an interface cable which requires millimeter-type lock ...
Page 27 - Jumper setting; Set the jumpers on the DM-D stand as follows:; Precautions on using the power supply unit
25 Eng li s h Jumper setting Set the jumpers on the DM-D stand as follows: The jumpers are located as follows: Precautions on using the power supply unit To avoid damage to the DM-D210 and the power supply unit, make sure to note the following points. ❏ Use the optional Seiko Epson products, PS-170,...
Page 28 - hole on the DM-D stand until you feel it click.
26 Assembling steps 1. Pass the cable for the DM-D210 through the DM-D stand. When extending the length of the DM-D stand, attach the extension support to the DM-D stand. 2. Insert the tab on the DM-D210 (or the extension support) into the hole on the DM-D stand until you feel it click. When using t...
Page 29 - Connect the cable for the DM-D210 to the display connector on the
27 Eng li s h 3. Connect the cable for the DM-D210 to the display connector on the DM-D stand until you feel it click. 4. Connect one end of the computer interface cable to the computer connector on the DM-D stand; then connect the other end to the RS-232 connector on the computer. Tighten the screw...
Page 30 - When not using the extension cable for power supply packed with
28 5. When using as a stand alone, go to step 6. When using with the printer, connect one end of the printer interface cable for the printer to the printer connector on the DM-D stand; then connect the other end to the connector on the printer. Tighten the screws on both ends of the cable to fasten ...
Page 31 - Connect the DC cable of the power supply unit (with the arrow
29 Eng li s h 7. Connect the DC cable of the power supply unit (with the arrow mark up) to the power supply unit connector indicated with “POWER IN” on the DM-D stand. 8. When using as a stand alone product, set the jumpers. (See “Jumper setting” on page 25.) 9. Arrange the cables as shown below. Pu...
Page 32 - Part Names and Functions; Exterior
30 Part Names and Functions Exterior ❏ Display: Characters are displayed. ❏ Power switch: The power is turned on/off. ❏ DIP switch: The functions of the DM-D210 are changed. (See “DIP switch” for details.) Note: When turning on the DM-D210 again after turning it off, wait for at least 3 seconds. pow...
Page 33 - DIP Switch; DIP Switch Functions; The functions of the DIP switche; DIP switch 1
31 Eng li s h DIP Switch DIP Switch Functions The DM-D210 has one DIP switch. The functions of the DIP switche are as follows: DIP switch 1 (*)This function can select whether or not you perform self test when turning on the power. See “Self Test” for details. Transmission speed DSW1 No. Function ON...
Page 34 - Setting the DIP switches; pen tip or small screwdriver.
32 Setting the DIP switches CAUTION: Turn off the DM-D210 while removing the DIP switch cover to prevent electrical damage to the DM-D210. 1. Turn off the power for the DM-D210. 2. Remove the DIP switch cover. 3. Change each setting of the switches with a pointed object, such as a pen tip or small s...
Page 35 - Turning and Tilting the DM-D210; The display area has the following range of movement:
33 Eng li s h Turning and Tilting the DM-D210 You can turn or tilt the display while holding the support. The display can be moved easily, so do not move any further if it stops. If you move it by force, you may damage it. With the “DM-D pole unit for IR” (DP-504) and the “DM-D pole unit for TM prin...
Page 36 - Self Test; Check Items of Self test; Diagnostics
34 Self Test The DM-D210 has a self test function. If you want to perform a self test, you must change the setting of the DIP switch. Check Items of Self test The following items are checked during the self test: ❏ Control ROM version ❏ DIP switch settings ❏ Memory switch settings ❏ Example of displ...
Page 37 - Specification; General Specifications
35 Eng li s h Specification General Specifications ❏ Height, Width, Depth and Weight 260mm 38mm 158mm 110mm 83mm 260mm 503mm <DM-D210 and DM-D stand> DM-D Stand(DP-210)
Page 39 - Tilt angle
37 Eng li s h • Base and support A of the “DM-D pole unit for IR” (DP-504): Height: 129 mm Width: 50 mm Depth: 53 mm Weight: 60 g • Base and support C of the “DM-D pole unit for TM printers (Type B)” (DP-503): Height: 248 mm Width: 50 mm Depth: 53 mm Weight: 116 g • Fixing plate A and support C of t...
Page 40 - Electrical Specifications; Type; Environmental Specifications; Storage environment
38 Electrical Specifications ❏ Type PS-170, PA-6508, PB-6509, PB-6510, PA-6511, PA-6513 (when using the DM-D stand) ❏ Rated voltage DC 11.4 to 48 V ❏ Rated current 0.4 A (max.) Environmental Specifications ❏ Operation environment Temperature: 5 ° C to 40 ° C Humidity: 30% to 85% (No condensation) ❏ ...
Page 41 - Character Specifications
39 Eng li s h Character Specifications ❏ Type of character • Alphanumeric characters: 95 • International characters: 37 • Extended graphics: 128 characters × 12 pages ❏ Character grid • Font : 5 × 7 dot, comma, period, annunciator • Character size 3.5 mm x 5.0 mm • Character pitch 9.9 mm Reliability...
