Epson 22-681- User Manual

6 A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will...

7 EXTENSION CORDS Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding typeplug and matching receptacle which will accept themachine’s plug. When using an extension cord, be sureto use one heavy enough to carry the...

8 UNPACKING AND CLEANING Carefully unpack the machine and all loose items fromthe shipping container(s). Remove the protective coatingfrom all unpainted surfaces. This coating may be removedwith a soft cloth moistened with kerosene (do not useacetone, gasoline or lacquer thinner for this purpose). A...

9 ASSEMBLY CUTTINGHEAD RAISING ANDLOWERING HANDWHEEL 1. Insert key (A) Fig. 7, into keyway (B) of raising and lowering shaft. Fig. 7 Fig. 8 2. Assemble handwheel (C) Fig. 8, to raising and lower-ing shaft as shown. Make sure key, which was assembled to shaft in STEP 1 , is engaged with keyway in hub...

10 ASSEMBLING SWITCH TO PLANER (THREE PHASE MACHINE ONLY) The switch for the three phase 15² Planer is supplied wired to the motor and is to be fastened to the planer asfollows: Fig. 10A 1. Line up the two holes (A) Fig. 10A, in the switch bracket (C) with the two threaded holes (B) in the left fron...

12 OPERATIONAL CONTROLS AND ADJUSTMENTS Fig. 18 A B LOCKING SWITCH IN THE “OFF”POSITION IMPORTANT: When the machine is not in use, the switch should be locked in the "OFF" position using a padlock (C) Fig. 19, with a 3/16" diameter shackle to preventunauthorized use. In the event of a po...

14 ANTI-KICKBACK FINGERS WHEN INSPECTING AND CLEANING THE ANTI-KICKBACK FINGERS, MAKE SURE THEMACHINE IS DISCONNECTED FROM THE POWERSOURCE. A series of anti-kickback fingers (A) Fig. 27, are providedon the infeed end of the planer, to prevent kickback ofthe workpiece during the planing operation. Th...

19 ADJUSTING SPRING TENSION OFINFEED AND OUTFEED ROLLERS The infeed and outfeed rollers are those parts of yourplaner that feed the stock while it is being planed. Thefeed rollers are under spring tension and this tensionmust be sufficient to feed the stock uniformly throughthe planer without slippi...

21 When using your machine, you may want to follow these few simple steps for achieving the best results possible. 1. True Up One Face – Feed one face of the board over a jointer, making thin cuts with each pass, until the entire surface is flat. 2. Plane to Thickness – Place the side you just surfa...

22 MAINTENANCE Fig. 53 Fig. 54 A B Fig. 55 E C D Fig. 56 F LUBRICATION The gear box oil should be changed once a year. Useextreme pressure gear oil, available from Delta in onepint cans (you will need approximately 20 oz.). The gearbox drain plug is shown at (A) Fig. 53. The oil fill andlevel plug i...

23 PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality pro...

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...