Page 2 - FOR YOUR SAFETY; FCC Class B Radio Frequency Interference Statement; Refer servicing to qualified personnel only.
i FOR YOUR SAFETY Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for...
Page 3 - ii
ii PRECAUTIONS: Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. ...
Page 4 - iii
iii circuit parts causing a fire or electric shock. Never spill liquids on the monitor. Do not attempt to service the monitor by yourself. Opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. Do not pull or ...
Page 5 - iv; GENERAL NOTES
iv GENERAL NOTES The following symptoms are normal with LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly...
Page 6 - OTHER NOTES
v OTHER NOTES The screen surface is very soft. Do not rub, touch or tap the screen surface with sharp object such as pen or pencil. This contact may scratch or damage the screen. These damages are not covered under the warranty. Turn your computer OFF before installing your new monitor. Refer to...
Page 7 - Disclaimer; Reference Information; on the bottom of its stand.; Monitor Information; Telephone
vi Disclaimer Envision Peripherals Inc. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, Envision Peripherals Inc. reserves the right to ...
Page 8 - vii; Table of Contents; Installation and Removal of the Base.........................3
vii Table of Contents 1 1 Important Safety Instructions ..........................................1 2 2 Features.............................................................................2 3 3 Unpacking the Monitor .....................................................3 Installation and Removal of ...
Page 9 - Important Safety Instructions; built-in installation unless proper ventilation is provided.
1 1 1 Important Safety Instructions Please read the following safety instructions before installing or cleaning your Envision monitor: 1. Unplug the monitor’s power cable from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a soft cloth to clean the monitor housing. 2. Sl...
Page 10 - Features
2 2 2 Features Your Envision EN9410e Monitor features: SXGA (1280 x 1024 pixel) Resolution LCD Panel True Colour Display With FRC support for 16.7M colours, the Envision EN9410e monitor offers you better image quality. High Quality Expansion With any resolution within the monitor’s specified r...
Page 11 - Unpacking the Monitor; Installation and Removal of the Base; Installation 2. Removal
3 3 3 Unpacking the Monitor Please check that the following items are included with your monitor. If they are missing or damaged, please contact your place of purchase immediately . Monitor 1 pc 1 pc 1 pc 1 pc Signal Cable Power Cable QSG (Quick Start Guide) CD User’s Manual Installation and Removal...
Page 12 - Hardware Installation; contact your electricity supplier.; Power cable
4 4 4 Hardware Installation Your monitor is equipped with an automatic power supply with a voltage range from 100 to 240 Volts AC at a frequency of 50 to 60 Hz. Make sure that your local power supply is within the supported range. If you are unsure, please contact your electricity supplier. To insta...
Page 13 - Windows driver Installation; Add New Hardware; Just follow the prompts to load the native Plug and Play drivers.; Windows XP
5 5 5 Windows driver Installation The Envision EN9410e is fully Windows compatible so no specific windows drivers are required to be loaded. Windows 98, ME, and 2000 The first time you start Windows after connecting your new monitor, the system will detect the monitor and automatically start the Add...
Page 14 - Setting the Display Resolution; Choosing The Best Resolution; Display; For Windows NT users only:; Test
6 6 6 Setting the Display Resolution Choosing The Best Resolution All Liquid Crystal Displays (LCDs) have a fixed resolution that is the same as the maximum resolution that may be displayed on the LCD. In the case of the EN9410e the LCD resolution is 1280 x 1024 pixels. This is also known as the “na...
Page 15 - Supported Graphics Modes and Refresh Rate Selection; Table 1
7 Supported Graphics Modes and Refresh Rate Selection There is no need to choose the highest possible refresh rate when using an LCD monitor. It is not technically possible for an LCD monitor to flicker. Even at a refresh rate of 60 Hz you will get an absolutely flicker-free image. For best results,...
Page 16 - Adjusting the Monitor
8 caused by the signal from the VGA card if it does not correspond with the usual standard. This is not however, a problem with the monitor. If it is still visible after using the Automatic adjustment, you can usually improve the displayed image by manually adjusting the phase, horizontal position a...
Page 17 - Picture Optimisation; The easiest way to obtain an optimal picture is by using the; Auto; button for 2; OSD Adjustment
9 7 7 Adjusting the Monitor Picture Optimisation The easiest way to obtain an optimal picture is by using the Auto button for 2 seconds. This only works reliably if the graphics adaptor is set to use one of the monitor’s factory modes (see Table 1 in the previous chapter) and if you are displaying a...
Page 18 - Brightness & Contrast Adjustment
10 (from left to right) Menu Enter OSD menu.Enter submenus or select items within OSD menu. Move the selection cursor upwards within the OSD menu. Move the selection cursor downwards within the OSD menu. Adjust OSD functions. (Decrease) Adjust OSD functions. (Increase) SELECT /AUTO Automatic...
Page 20 - Multi- Language selection
12 Color Adjustment Other There are three items for color adjustment: 9300K : Bluish white 6500K : Reddish white User defined: Red, Green, Blue. Adjust to set your own color level. LANGUAGE: Multi- Language selection OSD POSITION: Adjust the OSD window position on the screen. INFORMATION: “ON” When ...
Page 21 - Frequently Asked Questions; The image is blurred, how can I get the best quality picture?; Setting the Display Resolution; Why does the image look yellow, blue or pink instead of showing the
13 8 8 Frequently Asked Questions The image is blurred, how can I get the best quality picture? Read chapter 6, Setting the Display Resolution , and select a graphics signal with the correct resolution and refresh rate. Then read chapter 7, Adjusting the Monitor , and make adjustments to the displ...
Page 22 - MENU; NON PRESET MODE; The image is or distorted, flashes or flickers:
14 No image is displayed, what can I do? Check that the light (LED) next to the monitor’s power button is lit and is green in colour. If the LED is green, press the MENU button on the monitor to access the On Screen Display. If the message NON PRESET MODE appears there, please read chapter 6, Sett...
Page 23 - The display shows OUT OF FREQUENCY error message:
15 The display shows OUT OF FREQUENCY error message: Read chapter 6, Setting the Display Resolution , and select a graphics signal with the correct resolution and refresh rate.
Page 24 - Specifications; Display Characteristics
16 9 9 Specifications Model: Envision EN9410e Display Characteristics Display Type 19“ active matrix Thin Film Transistor Liquid Crystal Display Viewable Diagonal Area 43.3 cm / 19” Native (Maximum) Resolution 1,280 x 1,024 pixels Colors 16.7 million (6bpp+dithering) Dot Pitch 0.294 mm User Interfac...
Page 25 - Physical Characteristics; Energy Star; Regulatory Certification
17 Signal Connection 15-pin mini D-sub cable Physical Characteristics Power Management Energy Star Maximum Power Consumption 50 Watts Power Saving Mode < 1 Watts Operating Voltage Automatic switched mode power supply, 100 - 240 V, 50 - 60 Hz Dimensions (W x H x D) 426 x 435 x 214mm Weight 4.8 kg ...
