Page 2 - TABLE OF CONTENTS
EN9250 1 TABLE OF CONTENTS Table of Contents 1 For Your Safety 2 Precautions 3 General Notes 4-5 Before You Operate The Monitor 6 Installation Instructions 7-13 Operating Instructions 14-18 Technical Support (FAQ) 19-20 Appendix 21-24
Page 3 - FOR YOUR SAFETY
EN9250 2 FOR YOUR SAFETY Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the lim...
Page 4 - PRECAUTIONS
EN9250 3 ! Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. ! Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use onl...
Page 5 - GENERAL NOTES; OTHER NOTES
EN9250 4 GENERAL NOTES The following symptoms are normal with LCD monitor and do not indicate a problem. •••• Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. •••• You may f...
Page 7 - BEFORE YOU OPERATE THE MONITOR; CHECKING THE CONTENTS OF THE PACKAGE
EN9250 6 BEFORE YOU OPERATE THE MONITOR • 19” (48cm) TFT Color LCD Monitor • Crisp & Clear Display for W indows • Recommended Resolutions: 1280 X 1024 @ 60Hz • EPA E NERGY S TAR ® • Ergonomic Design with Height, Pivot, Tilt & Swivel Adjustable Stand • 3W +3W Stereo Speakers • Space Saving, C...
Page 8 - INSTALLATION INSTRUCTIONS; INSTALLING & REMOVING THE BASE; Install; INSTALLING THE BASE; Remove Pin; REMOVING THE BASE
EN9250 7 7 INSTALLATION INSTRUCTIONS INSTALLING & REMOVING THE BASE Install Figure 1 - Installing the Base. INSTALLING THE BASE 1. Set the bottom base on a flat surface. 2. Line up the front of the monitor with the front of the base and press firmly. Remove Pin Remove Base Figure 2 - Installing ...
Page 9 - female configuration.
EN9250 8 INSTALLATION INSTRUCTIONS (Cont) POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is requ...
Page 10 - Connecting The Cables; Figure 2 Connecting Cables
EN9250 9 INSTALLATION INSTRUCTIONS (Cont) Connecting The Cables Figure 2 Connecting Cables 1. AC Power Cord 2. 15-pin D-SUB Cable 3. DVI Cable 4. Audio Cable Turn off your computer before performing the procedure below. 1. Connect the female end of the AC power cord to the AC-in port on the back of ...
Page 11 - How To Install The INF & ICM Files; ENVISIONdisplay
EN9250 10 INSTALLATION INSTRUCTIONS (cont) How To Install The INF & ICM Files •••• This is a Plug & Play monitor. Microsoft W indows will automatically install a Plug & Play driver for it when you first install this monitor. It is not necessary to install the INF driver file included in ...
Page 12 - Figure 3; NOTES; cause damage or break the LCD screen.
EN9250 11 INSTALLATION INSTRUCTIONS (cont) Height, Tilt, Pivot & Swivel Adjustment Your monitor features a multi-adjustable stand that will enable it move 110mm up/down (height adjustment), 25 degree forward/backward (tilt adjustment), 90 degree landscape/portrait (pivot adjustment) and 70 degre...
Page 14 - Attaching The Optional Wall Mount Arm (not supplied); Follow these steps to finish installing the wall mounting arm:
EN9250 13 INSTALLATION INSTRUCTIONS (cont) Attaching The Optional Wall Mount Arm (not supplied) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 2. Inser...
Page 15 - OPERATING INSTRUCTIONS; EXTERNAL CONTROLS; Figure 4 - External Controls
EN9250 14 OPERATING INSTRUCTIONS EXTERNAL CONTROLS Figure 4 - External Controls 1. Power Button 4. > or Volume 2. LED 5. < or Volume 3. MENU / ENTER Button 6. Auto Adjust / Exit Button • Power Button: Press this button to turn the monitor ON or OFF. • MENU / ENTER: This button will activate th...
Page 17 - How To Adjust A Setting
EN9250 16 OPERATING INSTRUCTIONS (cont) How To Adjust A Setting 1. Press the MENU-button to activate the OSD window (Figure 4). 2. Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-...
Page 21 - to a display mode given in the Preset Display Modes table.; ERROR MESSAGE & POSSIBLE SOLUTION
EN9250 20 TECHNICAL SUPPORT (FAQ) (cont) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. W ith a wrong p...
Page 22 - APPENDIX; SPECIFICATIONS
EN9250 21 APPENDIX SPECIFICATIONS Size 48cm(19.0") LCD Pane Input V-Frequency 55-75Hz Display Colors 16.7M Colors Dot Clock 135MHz Max. Resolution 1280 x 1024 @75Hz Plug & Play VESA DDC 2B TM ON Mode ! 55W EPA E NERGY S TAR ® OFF Mode ! 2W D-Sub 15pin Input Connector DVI-D 24pin Analog:0.7Vp...
Page 24 - Preset Display Modes
EN9250 23 APPENDIX (cont) Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY(KHZ) VERTICAL FREQUENCY(HZ) 640 × 480 31.469 59.940 VGA 640 × 480 37.500 75.000 800 × 600 37.879 60.317 SVGA 800 × 600 46.875 75.000 1024 × 768 48.363 60.004 1024 × 768 56.476 70.069 VESA XGA 1024 x 768 60.023 75...
Page 25 - Connector Pin Assignment
EN9250 24 APPENDIX (cont) Connector Pin Assignment 1 5 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Red 9. NC 2. Green 10. Logic Ground 3. Blue 11. Monitor Ground 4. Monitor Ground 12. DDC-Serial Data ` DDC-return 13. H-Sync 6. R-Ground 14. V-Sync 7. G-G...
