Envision EFT920 - Manual - manualsarea.com

Page 2 - For Your Safety; FCC Statement

EFT920 2 v1_031004 EFT920 For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential inst...

Page 3 - Precautions

EFT920 3 v1_031004 EFT920 For Your Safety Precautions • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c...

Page 4 - General Notes

EFT920 4 v1_031004 EFT920 For Your Safety General Notes • Do not install the monitor near heat sources such as radiators or air ducts. • Do not place monitor in direct sunlight or in areas with excessive dust, mechanical vibration or shock. • Save the original shipping carton and packing materials i...

Page 5 - Before You Operate the Monitor; Installing & Removing the Base

EFT920 5 v1_031004 EFT920 Before You Operate the Monitor Installing & Removing the Base

Page 6 - Connecting the Wires Using the Power Cord Supplied

EFT920 6 v1_031004 EFT920 Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your monitor's power input socket. 3. Plug...

Page 7 - Operating Instructions; Front Panel Buttons

EFT920 7 EFT920 v1_031004 Operating Instructions Front Panel Buttons Exit : Press this button to save changes and close the OSD window. Brightness : Press this button to adjust the picture’s brightness. If the OSD window is open, this button allows you to move within the window and select desired fu...

Page 8 - Adjusting the OSD Settings

EFT920 8 v1_031004 EFT920 Operating Instructions Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 2. Press the < or > buttons until the desired function is highlighted. 3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the setti...

Page 9 - Windows INF Driver File

EFT920 9 v1_031004 EFT920 Operating Instructions Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional...

Page 11 - Appendix; Specifications

EFT920 11 v1_031004 EFT920 Appendix Specifications CRT Size 19.0" (48.3 cm) 11.4” (29 mm) neck 0.25mm(D), 0.21mm(H) dot pitch 90 degree deflection Viewable image size 18.0” (45.3 cm) diagonal Preset Display area 13.7” (346 mm) X 10.3” (260 mm) Dot Clock 200 MHz Maximum Resolution 1600 x 1200 pix...

Page 13 - Factory Preset Timing Table

EFT920 13 v1_031004 EFT920 Appendix Factory Preset Timing Table Standard Resolution (in pixels) Horizontal Frequency Vertical Frequency VGA 720 × 400 31.5 kHz 70 Hz 640 × 480 31.5 kHz 60 Hz VESA / 85 640 × 480 43.3 kHz 85 Hz 800 × 600 53.7 kHz 85 Hz 1024 × 768 68.7 kHz 85 Hz 1280 × 960 85.9 kHz 85 H...

Page 14 - Connector Pin Assignment

EFT920 14 v1_031004 EFT920 Appendix Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground

Envision EFT920 - Manual

Table of Contents:

Summary

Other Envision Models