Elo 2400LM - Manual

Caution • Power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. • This unit must follow the national requirement and local state laws to dispose unit. • Before connecting the cables to your Elo touchmonitor, make sure all components are powered OFF. Only ...

Classification With respect to electrical shock, fire in accordance with UL60601-1 and CAN/CSA C22.2 No. 60601-1 This monitor is a Class I (GROUNDED) DEVICE. These displays are classified NO APPLIED PARTS EQUIPMENT. Protection against harmful ingress of water: INGRESS PROTECTION (IPX1) (for monitor ...

viii European Standards and Classifications Standards: EN 60601-1-2: 2001+A1:2004 The EMC limits and test methods are referred to the following standards: Emission: Immunity CISPR 11: 2003+A1:2004 IEC 61000-4-2: 2008 AS/NZS CISPR CISPR22: 2006 IEC 61000-4-3: 2006+A1:2007 (Group 1, Class B) IEC 61000...

Guidance and manufacturer’s declaration-electromagnetic emissions The ET2400LM is intended for use in the electromagnetic environment specified below. The customer or the user of the ET2400LM should assure that it is used in such an environment. Emissions test Compliance Electromagnetic environment-...

Guidance and manufacturer’s declaration-electromagnetic immunity The ET2400LM is intended for use in the electromagnetic environment specified below. The user of the ET2400LM should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance Electromagnetic environme...

Recommended separation distances between portable and mobile RF communications equipment and the ET2400LM The ET2400LM is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the ET2400LM can help prevent electromagnetic int...

Warnings and Cautions ................................................. iv Warning ................................................................. iv Caution ................................................................... v Caution-Life Support ....................................................

C H A P T E R 1 I NTRODUCTION Product Description The 2400LM is a medical display designed to present information to the operator and the customer. The 2400LM is available in serial and USB(combo) touch interface as well as non-touch. The 2400LM functionally consists of a 24” LCD main display with a...

LCD Display Performance Features 24” TFT LCD Display Panel Display format 1920x 1200 Display area 518.4 mm (H) x 324.0 mm (V) Pixel pitch 0.270 mm (H) x 0.270 mm (V) Contrast Ratio 1000:1( typical) Brightness LCD 300 cd/m 2 (typical) IntelliTouch 270 cd/m 2 (typical) AccuTouch 240 cd/m 2 (typical) R...

C H A P T E R 2 I NSTALLATION A ND S ETUP This chapter discusses how to install your LCD touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following items are present and in good condition: LCD monitor VGA cable USB cable Serial cable Power ...

Touch Interface Connection NOTE: Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off. Remove the Cable Cover The cables are connected at the back of the monitor. To remove the cover, grasp the lip of the cover and pull towards you until...

STEP 1-Connecting the Video Cable • Tilt the screen up and back to access the connection ports. • Connect the 15-pin video cable (the ferrite bead end) or 24-pin DVI-D cable to the video port on your PC. • Connect the other end of the video cable to the video connector on your touchmonitor. • Secure...

STEP 2-Connecting the Serial and USB Touchscreen Cable • Connect the female end of the serial (RS-232) cable to the serial port on your PC, or connect the USB( ) touchscreen cable to the USB( ) touchscreen connector on the back of your touchmonitor. • Connect the male end of the cable to the serial ...

STEP 3-Connecting the Speaker Cable • Connect the light blue end of the speaker cable to the light blue speaker port to the monitor (audio in). • Connect the lime (light green) end of the speaker cable to the lime speaker port on the computer (audio out). 2-10 CONNECTIONS ON UNDERSIDE SPEAKER CABLE ...

STEP 4-Connecting the Power Cable Depending on where you live, you will use either the European or US/Canadian power cable. • Connect the female end of the power cable to the medical grade power adaptor. • Connect the brick power cable into the power port on the touchmonitor. • Route the cable throu...

Replace the Cable Cover Then you have attached all the cables to the monitor, gently bring all the cables toward the standard so they fit under the cover lip. Remove the screw from accessory and insert the screw into cable cover. Snap the Cable cover in place over the connections. 2-12 cable cover c...

Mounting the Display Your medically certified touchscreen display conforms to the VESA Flat Panel Monitor Physical Mounting Interface (FPMPMI) standard. The FPMPMI standard defines a physical mounting interface for flat panel displays. Your display conforms to the corresponding standards for flat pa...

2-14 Rear Mounting Using the VESA Interface 1 If the display is already connected to a pedestal, remove the four screws that connect the pedestal to the display (refer to Figure2-1 , item 1 ). Separate the pedestal from the display. 2 Reinstall the four screws into the VESA interface mount. Ensure t...

Installing the Serial Touch Driver Installing the Serial Touch Driver for Windows 7, Windows Vista, Windows XP, Windows 2000, ME, 95/98 and NT4.0. NOTE: For Windows 2000 and NT4.0 you must have administrator access rights to install the driver. Make sure the serial connector (RS232) is plugged into ...

Installing the Serial Touch Driver for MS-DOS and Windows 3.1 You must have a DOS mouse driver (MOUSE.COM) installed for your mouse if you wish to continue using your mouse along with your touchmonitor in DOS. To install Windows 3.x and MS-DOS touch driver from Windows 95/98, follow the directions b...

Installing the USB Touch Driver Installing the USB Touch Driver for Windows 7, Windows Vista, Windows XP, Windows 2000, ME and Windows 98. 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. If Windows 98 or Windows 2000 starts the Add New Hardware Wizard, do the following: 2 Choose Next. Selec...

C H A P T E R 3 O PERATION About Touchmonitor Adjustments Your touchmonitor will unlikely require adjustment. Variations in video output and application may require adjustments to your touchmonitor to optimize the quality of the display. For best performance, your touchmonitor should be operating in...

Bottom Panel Controls Control Function 1 Menu/Exit Display/Exits the OSD menus. 2 1. Enter contrast of the OSD. 2. Increase value of the adjustment item. 3. Shuffle item clockwise. 3 1. Enter audio volume adjustment. 2. Decrease value of the adjustment item. 3. Shuffle item counter-clockwise. 4 Sele...

Controls and Adjustment OSD Menu Functions To Display and Select the OSD Functions: 1 Press the Menu key to activate the OSD menu. 2 Use or to move clockwise or counterclockwise through the menu. Press the select key on the monitor. The parameter will be highlighted when selected. 3 To quit the OSD ...

OSD Control Options Control Description Contrast Increases or decreases contrast. Brightness Increases or decreases brightness. V-Position Moves the screen up or down. H-Position Moves the screen left or right. Recall Defaults Returns the monitor to its default settings. Color Balance Press or and “...

Power Display & Power Saving General Power Saving Mode Power Mode Consumption On 56.4w max.(DC power) Sleep 4w max. (DC power and without Audio performing) 15w max. (DC power and with Audio performing) Off 2w max. Tested with the USB cable unplugged. We recommend switching the monitor off when i...

C H A P T E R 4 T ROUBLESHOOTING If you are experiencing trouble with your touchmonitor, refer to the following table. If the problem persists, please contact your local dealer or the Elo service center. Solutions to Common Problems Problem Suggestion(s) The monitor does not respond 1. Check that th...

A P P E N D I X A N ATIVE R ESOLUTION The native resolution of a monitor is the resolution level at which the LCD panel is designed to perform best. For the Elo LCD touchmonitor, the native resolution is 1920 x 1200 for the WUXGA- 24 inch size. In almost all cases, screen images look best when viewe...

A P P E N D I X B T OUCHMONITOR S AFETY This manual contains information that is important for the proper setup and maintenance of your touchmonitor. Before setting up and powering on your new touchmonitor, read through this manual, especially Chapter 2 (Installation), and Chapter 3 (Operation). 1 T...

Care and Handling of Your Touchmonitor The following tips will help keep your touchmonitor functioning at the optimal level. • To avoid risk of electric shock, do not disassemble the brick power supply or display unit cabinet. The unit is not user serviceable. Remember to unplug the display unit fro...

A P P E N D I X C T ECHNICAL S PECIFICATIONS Display Modes Your Elo touchmonitor is compatible with the following standard video modes: Item Resolution Type H.Scan(KHz) V. Scan(Hz) Polarity 1 640 x 480 VGA 31.468 25.175 -/+ 2 800 x 600 VESA 56 35.156 36.000 +/+ 3 800 x 600 VESA 60 37.879 40.000 +/+ ...

Touchmonitor Specifications Model 2400LM LCD Display 24” TFT Active Matrix Panel Display Size 518.4(H) x 324.0(V) mm Pixel Pitch 0.270(H) x 0.270(V) mm Display Mode VGA 640 x 480 (60 Hz) SVGA 800 x 600 (56 / 60 Hz) XGA 1024 x 768 (60 Hz) SXGA 1280 x 960 (60 Hz) SXGA 1280 x 1024 (60 Hz) WXGA 1360 x 7...

Power Supply Specification The Touchcomputer shall be powered by 12VDC from a universal type power supply brick with the following characteristics: Input voltage 100 to 240 V~ Input frequency 50/60 Hz Output voltage 12 V Output load regulation +/- 5%, Line regulation +/- 1% Output current=6.5 A C-31

R EGULATORY I NFORMATION I. Electrical Safety Information: A) Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, da...

III. Agency Certifications The following certifications have been issued for this monitor: • Australia C-Tick • Canada cUL • Canada IC • Europe CE • Japan VCCI • United States FCC • United States UL • China CCC This class B digital apparatus meets all requirements of the Canadian Interference-Causin...

W ARRANTY Except as otherwise stated herein or in an order acknowledgment delivered to Buyer, Seller war- rants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the touchmonitors and components of the product is 3 (three) years. Seller makes no warran...

© 2010 T yco Electronics. Printed in USA Check out Elo’s Website! www.elotouch.com Get the latest... • Product information • Specifications • News on upcoming events • Press release • Software drivers • Touchmonitor Newsletter Getting in Touch with Elo To find out more about Elo’s extensive range of...