Dixon ZTR 304 - Manual
Dixon ZTR 304 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PARKING BRAKE ADJUSTMENT; Raise upper body to the open position.; REMOVING THE MOWER BLADE; Caution should be exercised when service is required on blade.
- Page 3 – Page 3
- Page 4 – P a g e 4
- Page 6 – P a g e 6
9/89 (Revised)
Page 1
TECHNICAL DATA BROCHURE
(MODEL ZTR 304)
IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS
BODY REMOVAL
1 . T h e 3 0 4 h a s a ( 2 ) p i e c e f a b r i c a t e d s t e e l b o d y . T h e u p p e r b o d y c a n b e f o l d e d
fo r w a r d t o e x p o s e t h e t r a n s a x l e . In s o m e c a s e s , i t m a y b e n e c e s s a r y to r e mo v e
th e upper body to s e r v i c e t h e transaxle.
\
2 .
To remove upper body, fold f o r w a r d and r e m o v e b o l t (P/N 3 0 0 6 ) from cable ( P / N
3 7 8 0 ) . S h u t u p p e r b o d y a n d r e m o v e t h e t w o c o t t e r p i n e s ( P / N 3 0 5 8 ) f r o m t h e
front of upper body s u p p o r t . C a r e f u l l y l i f t upper body f r o m frame.
3. Reverse above procedure to r e i n s t a l l .
SE A T A D J U S T M E N T
1. Raise upper body.
2.
Loosen four s e a t bolts (P/N 3093) and slide s e a t forward or backward to
d e s i r e d p o s i t i o n .
3. Retighten bolts.
MO W E R B L A D E O P E R A T I O N
To engage the mower blades, t u r n lever on floor slowly to the "ON" position. To
disengage mower blades, t u r n l e v e r s l o w l y to the "OFF" p o s i t i o n .
REMOVING MOWER DECK
*
1 . L o o s e n t h e b e l t k e e p e r ( P / N 7 0 2 6 & 7 0 2 7 ) , l o c a t e d u n d e r t h e e n g i n e , b y l o o s i n g
t w o r e a r e n g i n e m o u n t i n g b o l t s , a l l o w i n g t h e d e c k d r i v e b e l t t o c o me f r e e o f t h e
r e a r p u l l e y .
2. Disconnect t h e w i r i n g l o o m at t h e deck s a f e t y s w i t c h (P/N 4 2 4 2 ) .
3 . Remove* the two clevis pins (P/N 3 0 7 2 ) f r o m the two r e a r L - r o d s (P/N 1355) and
s l i d e f r o m s l o t s .
4 . Remove clevis pins (P/N 3 0 7 2 ) L-rod a t t a c h e d to l i f t handle and slide from slot.
5. Remove clevis pin (P/N 3 0 7 2 ) f r o m f r o n t deck hanger' s h a f t (P/N 1332), located at
f r o m o f m o w e r d e c k o n s l i d e p l a t e s w e l d e d at b a t t e r y box and remove.
6 . Lift front of mower c h a s s i s and r o l l f r e e o f t h e deck.
7. To install, reverse the above procedure.
IDJUSTMENT OF MOWER DECK DRIVE BELT
1. The m o w e r deck d r i v e b e l t is t e n s i o n e d by a s p r i n g l o a d e d engagement idler
quadrant.
2. This system is designed to maintain the p r o p e r belt tension at all times.
3. Belt tension can be a d j u s t e d by moving the engaging rod (P/N 7013) into the
o u t s i d e hole of engagement handle (P/N 7020).
4. A f t e r belt tension is adjusted, check to assure that the m o w e r blade will not
t u r n freely when the engaging r o d is in the "OFF" position.
5. If the mower blade .urns f r e e l y , a d j u s t the blade by loosening*nut' (P/N 3205) at
end of the brake linkage (P/N 7015).
6. A f t e r adjustment is achieved, p e r f o r m the s a f e t y checks listed below.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 " I M P O R T A N T " - P E R F O R M S A F E T Y C H E C K S A F T E R M A K I N G A N Y R E P A I R S O R A D J U S T M E N T S 1. A f t e r reassembly, while s e a t e d on mower a t t e m p t to s t a r t engine w i t h mower deck engaged. Engine should not s t a r t . If engine d...
