Page 2 - IRELESS; AFETY; NSTALLATION; ARE AND
R EGULATORY F ACTORS W IRELESS R EMOTE C ONTROL This device complies with Part 15 of FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause und...
Page 4 - EMOTE
2 121716 R EMOTE C ONTROL B ASICS This remote control gives you easy access to all the featuresof a DISH Network satellite TV receiver and lets you control PVRfeatures of a DISH Network DishPVR satellite receiver. These PVRfeatures let you record programming with full digital quality,without a VCR.Y...
Page 5 - IR; UHF REMOTE ANTENNA; : Set the antenna straight up so you can use the remote; Note; : If you don’t attach the antenna, you can still use the remote
121716 3 R EMOTE C ONTROL S IGNALS : UHF AND IR The remote control uses both Ultra High Frequency (UHF) radiosignals and Infrared (IR) light signals to control the receiverbut uses only IR signals to control other devices. • IR signals travel only short distances (40 feet or less),and can’t go throu...
Page 7 - EGULAR; : The remote comes already set up to control the receiver, unless; : Limited mode is not used with cable boxes or amplifiers.
121716 5 R EMOTE C ONTROL M ODES R EGULAR M ODES You can set the remote to four different modes to control the receiveror other devices. Set up the remote to control a device like a TV or a VCR. See Set Upthe Remote Control on page 6 for what to do. Note : The remote comes already set up to control ...
Page 8 - P THE; ETTING; TV
6 121716 R EMOTE C ONTROL S ETUP S ET U P THE R EMOTE C ONTROL On the next few pages we tell you how to set up the remote to controla TV, a VCR, or other devices. When you get the remote it’s already set up to control thereceiver, unless you have changed the address on yourreceiver. However, you mus...
Page 9 - CAN FOR; AUX
121716 7 7. Press the POUND ( # ) button. If you entered the code correctly, the mode button flashes three times. 8. Press the blank POWER button to test if the code works for the device. If it does, the device shouldturn off. 9. Turn the device back on and try some other buttons to make sure they w...
Page 10 - HECK THE
8 121716 4. Press the blank POWER button. 5. Press the UP or DOWN ARROW button until the device turns off. You will have to do thisrepeatedly to scan through all codes. Note : Do not press the ARROW buttons too quickly because you could skip over the codefor your device. Note : The mode button for t...
Page 11 - For AUX mode, the first group of flashes tells you what the; HANGE THE
121716 9 For AUX mode, the first group of flashes tells you what the AUX mode controls. A quick flash (zero) before the three-digit code is for a TV; one regular flash is for a VCR; and two flashesis for a tuner, amplifier, or cable box. For example, if the TVcode is 570, the AUX mode button flashes...
Page 12 - Important System Information; To set the remote to control the device’s volume :
10 121716 8. Press the SELECT button to close the Important System Information screen. S WITCH B ETWEEN TV AND D EVICE V OLUME C ONTROL When you set up the remote to control a TV, the MUTE and VOLUME buttons control the TV volume. However, if you want to use the AUX mode to control a tuner or amplif...
Page 13 - ONTROL THE; AT; keep the remote in; IDEO
121716 11 4. Press the 0 number button. 5. Press the POUND ( # ) button. The TV mode button flashes three times. 6. Press the SAT mode button. 7. Press the plus (+) and minus (-) sides of the VOLUME button.The TV’s volume changes and the TV mode button lights instead of the AUX mode button. R EMOTE ...
Page 16 - Program Banner; PVR B; DishPVR
14 121716 V IEW B UTTON • When you watch a program, press this button to briefly displaythe Program Banner . • When you use a menu, press this button to canceland go back to watch a program. C ANCEL B UTTON Press this button to cancel and go back to the previous menu or towatch a program. D ISH PVR ...
Page 19 - NUMBER; Search; ONTROL A
121716 17 • Search - Use the letters above the NUMBER buttons while in the Search menu. For example, when looking for the channel and times to watch Rudy Fremmel Presents, you press 7 three times for an R , 8 two times for a U , 3 one time for a D , and 9 three times for a Y to spell the word “Rudy”...
Page 20 - TV M; only the TV you set up in
18 121716 TV M ODE B UTTON You must first set up the remote to control the TV. See Set Up theRemote Control on page 6. Then press the TV mode button to set the remote to TV mode. The TV mode button will stay lit for two seconds to show you’ve set the remote to TV mode. Make sure you keep the remote ...
Page 21 - SELECT
121716 19 U P /D OWN A RROW B UTTONS Use these buttons to change channels on the TV. Note : These buttons do not change the channels on the TV if the remote control is in limited mode. S ELECT B UTTON The SELECT button works as the ENTER button for a TV. R ECALL B UTTON Press this button to go back ...
Page 23 - VCR B; UTTONS
121716 21 U P /D OWN A RROW B UTTONS Use these buttons to change channels on the VCR. Note : If you are using the remote control in Limited Mode, the TV will not change channels. VCR B UTTONS • Press the BACK button to rewind a videotape. • Press the PAUSE button to pause a videotape. Press this but...
Page 24 - TV B; OX
22 121716 C ONTROL A C ABLE TV B OX Only the buttons we tell you about here control acable TV box. Some of the buttons we tell youabout here may not control your cable TV box.See your cable box user ’s manual for informationabout the box’s features. A UX M ODE B UTTON You must first set up the remot...
Page 27 - INPUT SELECT
121716 25 M UTE B UTTON Press this button to turn on or off the sound. Note : Program the remote to control the device’s volume by following the instructions on page 10. V OLUME B UTTON Press this button to raise ( + ) or lower ( - ) the sound volume. Note : Program the remote to control the device’...
Page 28 - TV C; ODES
26 121716 D EVICE C ODES These tables contain the manufacturer codes for programming theremote to control your TV, a VCR, DVD player, cable box, or audioamplifier. Every attempt has been made to include all codes. If yourdevice brand is not listed or if the codes to not work, the remote maynot contr...
Page 30 - VCR C
28 121716 VCR C ODES Sy mphonic 632, 692, 694 Tandy 605, 613 Tatung 509, 698 Tec hnics 508 Tec hwood 523, 573 Tek nika 504, 505, 516, 518, 522,523, 524, 525, 526, 534,536, 541, 614, 615, 686,691, 712 Teleav ia 551 Telefunken 551 Teletech 532 Tera 513 Thom as 695 Thom pson 709 Thom son 551, 616 TMK 5...
Page 31 - ABLE
121716 29 M agnavox 527, 553, 554, 556, 565,611 M arantz 530, 554, 565, 585, 592,594, 600, 601, 603 M EI 554 M em orex 533, 549, 554, 566, 581,585, 588, 608 M GA 567, 568, 609 M itsubishi 562, 567, 568, 569, 570,571, 609 M TC 544, 580, 588 M ultitech 588, 589, 591 NAD 573 NEC 530, 531, 532, 562, 592...
Page 32 - DVD P; LAYER
30 121716 DVD P LAYER C ODES T UNER /A MPLIFIER C ODES DVD Players Codes Aiwa 634 Hitachi 632, 635 J VC 636 Konk a 637, 638 M agnavox 626 M itsubishi 629 Panasonic 639 Philips 640, 641, 642 Pioneer 619 RCA 627 Sany o 643 Sony 617, 644, 645 Tos hiba 616, 646, 647 Zenith 648 N ote: You must put the re...
Page 37 - OU
121716 35 A CCESSORY W ARRANTY An accessory is any DISH Network branded equipment, displaying the DISHNetwork logo, excluding the receiver, Smart Card, cables and hookups, andnon-mechanical components. A one-year warranty becomes effective upon theactivation of the DISH system or date of purchase, i...
Page 38 - NDEX
36 121716 I NDEX A Address, Change the 9Amplifier Codes 30Amplifier, Control an 24Antenna, Remote Control, Attach the3Attenuator, Install an 4 B Batteries, Remote Control 2Buttons, Remote Control 11 C Cable TV Box Codes 29Cable TV Box, Control a 22Change the Address 9Check the Device Codes 8Customer...
