Dish Network EZ Remote - Manual

Page 2 - iv; Figure 1. The EZ Remote

iv Figure 1. The EZ Remote See How to Use the Remote Control for more details oneach button. SELECT POWER GUIDE SAT TV CHANNELCONTROL T H EM E B RO WS E CHANNEL C HANNEL INFO VOL CANCEL 1 2 3 4 5 6 7 8 9 0 RECALL MUTE Turn on/off the satellite receiver Turn on/off the TV Channel up Get informationab...

Page 3 - SATELLITE CHANNEL CONTROL; - Press to switch your; TV POWER

1 A BOUT THE DISH N ETWORK EZ R EMOTE C ONTROL The DISH Network EZ Remote Control makes operatingyour DISH Network satellite receiver easy andconvenient. This remote control includes large, easy-to-find buttons which are most commonly used to control thebasic satellite receiver features you need. In...

Page 4 - Press down on the arrow on the battery cover and

2 To use these added buttons and other features to controlyour TV, follow the step-by-step instructions below to setup your remote control. This setup also requires you toconnect your satellite receiver to your TV’s tuner usingcoaxial cable. After completing your setup, see How toUse the Remote Cont...

Page 5 - Note; TV

3 R ECEIVER U PGRADE Turn on your TV the way you normally would to watchsatellite TV programming. Using your DISH Network EZRemote Control, press and then try using this remote control to operate some basic satellite receiver featureslike MENU or GUIDE . If the remote control does not work, your sat...

Page 6 - Figure 2. Connect the Satellite Receiver and TV; TV Set Out

4 C ONNECTING Y OUR S ATELLITE R ECEIVER AND TV Figure 2. Connect the Satellite Receiver and TV 1. Connect a coaxial cable between the TV Set Out on the satellite receiver and the tuner input on the TV(see Figure 2). Note : If you connect your TV a different way (for example, using yellow, red, and ...

Page 7 - MUTE

5 S ETTING U P THE R EMOTE TO C ONTROL Y OUR TV 1. Find the brand name of your TV in the TV code tables starting on page 30. You will be referring tothis location for codes in the instructions below. 2. Turn on your TV. 3. Press and hold until both lights turn on (it takes about five seconds). 4. Re...

Page 8 - Menu

6 S ETTING U P ON Y OUR R EMOTE C ONTROL • Press and to change channels on your TV. • Press to change the TV volume. If these buttons work, go on to the next section toset up . If not, pick another code for your TV brand from the TV Codes table and go back tostep 3. 1. Make sure your TV and satellit...

Page 10 - Table 1: How I Change My TV Channels; Select

8 Table 1: How I Change My TV Channels Column 1:How do you change your TV toChannel 3 using the numberbuttons? Column 2:Circle the numbersequence you use tochange your TV toChannel 3 “I just press the number buttonson my remote to change thechannel.” If you only press 3 on yourremote control to chan...

Page 12 - to switch your TV

10 S ETTING U P TO S WITCH THE TV TO A P REFERRED O FF -A IR C HANNEL If you watch local programming from an off-air antenna,follow these instructions to set up to switch your TV to your preferred off-air channel. You will need toconnect your off-air antenna to your satellite receiver andthen set up...

Page 13 - If the number you wrote in step 1 is a 2-digit number; SELECT

11 S ETTING U P ON THE R EMOTE C ONTROL 1. In the blank below, write down your preferred off- air channel that you want your TV to tune to whenyou press . 2. If step 19 on page 9 is blank and was not used to set up , go to step 8. Otherwise, go to step 3. 3. In the blank below, write down the number...

Page 16 - and TV; ETTING; VCR; RECALL

14 Figure 4. Connecting a Satellite Receiver, VCR, and TV S ETTING U P THE R EMOTE TO C ONTROL Y OUR VCR 1. Find the brand name of your VCR in the VCR code tables starting on page 37. You will be referring tothis location for codes in the instructions below. 2. Turn on your VCR. 3. Press and hold un...

Page 17 - MENU

15 S ETTING U P O N Y OUR R EMOTE C ONTROL 8. If light flashes three times, the code is valid and you can go to step 9. If light does not flash at all, the code may not have been enteredcorrectly. So, start over from step 3 and try the codeagain. 9. Press while looking at the channel number display ...

Page 19 - Table 2: How I Change My VCR Channels

17 Table 2: How I Change My VCR Channels Column 1:How do you change your VCRto Channel 3 using the numberbuttons? Column 2:Circle the numbersequence you use tochange your VCR toChannel 3 “I just press the number buttonson my remote to change thechannel.” If you only press 3 on yourremote control to ...

Page 20 - IS; to Pass Satellite Programming Through Your VCR to

18 U SING W HEN A VCR IS I NSTALLED If you installed a VCR using the instructions in Setting Up to Pass Satellite Programming Through Your VCR to Your TV on page 12, but you would like to use to switch your TV to the preferred off-air channel, make sureyour VCR is turned off before pressing . 16.If ...

Page 21 - OW TO; TV C; ODES

19 O THER R EMOTE C ONTROL I NSTRUCTIONS H OW TO S CAN FOR TV C ODES If the code for your TV is not in the TV Codes tablesstarting on page 30, complete the following instructions toscan for your TV’s code. 1. Make sure your TV is on. 2. Hold until lights turn on (it takes about five seconds). 3. Rel...

Page 22 - VCR C

20 H OW TO S CAN FOR VCR C ODES If the code for your VCR is not in the VCR Codes tablesstarting on page 37, complete the following instructions toscan for your VCR’s code. 1. Make sure your VCR is on. 2. Hold until lights turn on (it takes about five seconds). 3. Release . light flashes. 4. Press th...

Page 23 - Example

21 H OW TO C HECK THE TV C ODES You can find out what TV code is set up in your remotecontrol when you complete the following instructions. H OW TO C HECK THE VCR C ODES You can find out what VCR code is set up in your remotecontrol when you complete the following instructions. 1. Hold until lights ...

Page 25 - ATELLITE; which will do three things:; SAT POWER B; UTTON; Press the; SAT POWER; button to turn the satellite receiver

23 H OW TO U SE THE R EMOTE C ONTROL This section describes how to use your DISH NetworkRemote Control. Figure 1 on page iv shows the remotecontrol with a brief description of the buttons. P OINTING THE R EMOTE C ONTROL The remote control uses infrared (IR) light signals tocontrol the satellite rece...

Page 26 - TV POWER B; MENU B; Main Menu; VOLUME B; UTTONS; VOLUME; GUIDE B; Program Guide

24 TV POWER B UTTON Press the TV POWER button to turn the TV ON or OFF. This button works only if you have completed theinstructions in Setting Up the Remote to Control Your TVon page 5. MENU B UTTON Press the MENU button to open the Main Menu . VOLUME B UTTONS Press the VOLUME buttons to raise ( + ...

Page 27 - SELECT B

25 UP/DOWN/LEFT/RIGHT B UTTONS • Change channels - Press the UP or DOWN button. • Open the Browse Banner - Press the RIGHT button. • Show Themes - Press the LEFT button. • Move around within the Program Guide , the menus, and Browse Banner - Press the UP , DOWN , LEFT , and RIGHT buttons. SELECT B U...

Page 28 - CANCEL B

26 CANCEL B UTTON • Cancel - Press the CANCEL button to cancel a procedure and go back to the previous menu or towatching a program. • View - Press and hold the CANCEL button until both lights turn on. When you release the button, you will return to watching TV. N UMBER B UTTONS • Change the channel...

Page 29 - DISH B; DISH; RECALL B; MUTE B

27 DISH B UTTON Press the DISH button to go to Dish Home for receivers that support Dish Home. RECALL B UTTON • Recall - Press the RECALL button to return to the last satellite receiver channel you watched. Press it againto switch between the last two satellite receiverchannels you watched. • * - Pr...

Page 30 - POWER B; button to turn the TV on or off.; Press these buttons to raise (

28 U SING THE R EMOTE C ONTROL FOR O FF -A IR TV P ROGRAMMING O FF -A IR C HANNEL C ONTROL B UTTON To use the remote control to get programs from an off-airantenna and operate your TV, you must first press , which will do three things: • Turns off the satellite receiver to pass through youroff-air a...

Page 32 - AND; TV Brand

30 TV AND VCR C ODES These tables contain the manufacturer codes forprogramming the remote control to control your TV orVCR. Every attempt has been made to include all codes.If your TV or VCR is not listed or the codes do not work,the remote may not control your device. In some casescodes may operat...

Page 39 - VCR Brand

37 VCR C ODES VideoConcepts 570, 691 Vidtech 505, 695, 712 Viking 522 Wards 505, 506, 515, 518, 534, 536, 543, 564,565, 567, 568, 607, 619, 712, 714, 715 Yamaha 505, 506, 712 York 695 Zenith 501, 518, 693 Zonda 620 VCR Brand Code Aiwa 588 Akai 513, 514, 515, 516, 518, 519, 520 Alba 546 Amstrad 588 A...

Dish Network EZ Remote - Manual

Table of Contents:

Summary

Other Dish Network Models