Dimplex DCP7W - User Manual

Control Panel (1) Mode button (2) Temp decrease (-) button (3) Indicator light (4) LED display screen (5) Temp increase (+) button (6) Power button FRESH( Press 3s ) (1) (2) (3) (4) (5) (6) Mode button: Selects the appropriate operating mode. Each time you press the button, a mode is selected in a s...

LED Display Shows the set temperature while on Cool, Heat or Auto mode (on some models). While on Dry and Fan modes, it shows the room temperature. Error codes: E0 - EEPROM error.E1 - Room temperature sensor error.E2 - Evaporator temperature sensor error.E3 - Condenser temperature sensor error (on s...

Remote Control Note: All indicators shown in the figure are for the purpose of clear presentation. But during the actaul operation, only the relative function signs are shown on the display window. Displayed when data transmitted. Displayed when remote controller is ON. NO display High speed Medium ...

Installation EXHAUST HOSE INSTALLATION The exhaust hose and adaptor must be installed or removed in accordance with the usage mode. For COOL, HEAT (heat pump type) or AUTO (on some models) mode the exhaust hose must be installed. For FAN, DRY or HEAT (electrical heat type) the exhaust hose should be...

Installation WINDOW KIT INSTALLATION The window slider kit has been designed to fit most standard vertical and horizontal window applications, however it may be necessary for you to modify some aspects of the installation procedures for certain types of windows. Step one: Preparing the exhaust hose ...

Installation WINDOW KIT INSTALLATION Step two: Install the exhaust hose assembly to the unit Push the Exhaust hose into the air outlet opening of the unit along the arrow direction. Step three: Preparing the adjustable window slider 1. Choose the window sliders according the size of your window. If ...

Installation WINDOW KIT INSTALLATION Note: Once the exhaust hose assembly and adjustable window lider are prepared, choose from one of the following two installation methods. Type 1: Hung Window or Sliding Window Installation (for some models) Or and frame as shown. 1. Cut the adhesive foam seal A a...

Installation Type 2: Wall Installation (for some models)1. Cut a 125mm (4.9inch) hole into the wall for wall exhaust adaptor B.2. Secure the wall exhaust adaptor B to the wall using the four anchors and screws provided in the kit.3. Connect the exhaust hose assembly (with wall exhaust adaptor A) to ...

Installation TOOLS NEEDED • Medium Philips screwdriver• Tape measure or ruler• Knife or scissors• Saw (optional, to shorten window kit for narrow windows ACCESSORIES (not all accessories supplied with all models) Nam e Qty. of Acce ssories Shape Shape Qty. Nam e of Acce ssories 1 pc(*) Window Slider...

Operating Instructions COOL operation · Press the "MODE" button until the "COOL" indicator light comes on.· Press the ADJUST buttons "+" or "-" to select your desired room temperature. The temperature can be set within a range of 17°C~30°C/62°F~88°F(or 86°F).· Press t...

Operating Instructions Constant Fan button (On some models) In Cooling or Dry mode, press the button for 3 seconds to turn on or off the constant fanfunction. When the function is turned on, the constant fan light will illuminate, identifyingthe fan continuous run for cooling. When the function is t...

WATER DRAINAGE · During dehumidifying modes, remove the drain plug from the back of the unit, install the drain connector (5/8" universal female mender) with 3/4" hose (purchased separately). For the models without drain connector, just attach the drain hose to the hole. Place the open end o...

Cleaning SAFETY PRECAUTIONS • Always unplug the unit before cleaning or servicing.• DO NOT use flammable liquids or chemicals to clean the unit.• DO NOT wash the unit under running water. Doing so causes electrical danger.• DO NOT operate the machine if the power supply was damaged during cleaning. A...

Storage If not using the unit for an extended period of time, after cleaning please:• Turn the unit OFF, unplug and take care of the mains lead & plug.• Drain any water from the unit according to the instructions in the following sections.• Run the appliance on FAN MODE for 12 hours in a warm ro...