Dewalt DW788 - Manual - manualsarea.com

Page 2 - English; IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

English IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D E WALT TOOL, CALL US TOLL FREE AT: 1-800-4-D E WALT (1-800-433-9258) WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING SAW • DO NOT WEAR GLOVES, NECKTIES, JEWELRY OR LOOSE CLOTHING • CONTAIN LONG HAIR • ALWAYS WEA...

Page 3 - For your own safety read instruction manual before; Grounding Instructions; KEEP GUARDS IN PLACE and in working order.

WARNING: For your own safety read instruction manual before operating tool. Grounding Instructions In the event of a malfunction or breakdown, grounding provides a pathof least resistance for electric current to reduce the risk of electricshock. This tool is equipped with an electric cord having ane...

Page 4 - CHECK DAMAGED PARTS. Before further use of the tool, a guard; Additional Safety Rules for Scroll Saws; DO NOT use the upper arm as a lifting point.

2 • OUTDOOR USE EXTENSION CORDS. When tool is usedoutdoors, use only extension cords intended for use outdoors andso marked. Minimum Gage for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere Rating More Not more AWG Than Than 0 - 6 1...

Page 5 - SAVE THESE INSTRUCTIONS; Mounting; BEFORE INSTALLING A BLADE, UNPLUG THE SCROLL SAW.; Scroll saws cut on the downstroke, so it is

• CAUTION: Some wood contains preservatives such as copper chromium arsenate (CCA) which can be toxic. When cutting thesematerials, extra care should be taken to avoid inhalation and tominimize skin contact. • USE a dust mask and safety glasses when sawing. • KEEP GUARDS in place and working order. ...

Page 6 - Blade Tension Lever; The material hold-down (Figure 7) should contact the surface of the

4 the thumbscrew. Next, insert the top of the blade into the top bladeclamp and securely tighten the top thumbscrew.Properly adjust the tension of the blade before operating your scrollsaw. (See: Blade Tension Lever section of this manual.) Blade Tension Lever Move the blade tension lever (Figure 6)...

Page 7 - When cutting, ensure the material hold-down does not; Air Hose

workpiece. To adjust the material hold-down, loosen the thumbscrew(Figure 7) and move the rod up or down. The material hold-downmust be beveled when the table is beveled. To bevel the materialhold-down, loosen the allen screw shown in Figure 7 and bevel thematerial hold-down until it is parallel to ...

Page 8 - Before tilting the table for bevel cuts of 45 ̊,check the; INSIDE CUTS; Readjust the blade tension and begin the inside cut.

6 Sawing Hold material firmly against table. Always feed material toward theblade. Feed the workpiece fast enough to allow the blade to cut, butdo not force material into the blade too quickly. Beveling The table of your scroll saw bevels 45° left and right. A detent is set at0°. To bevel the scroll...

Page 9 - BRUSHES; WALT brushes. New brush assemblies are available

NOTE: Do not lift saw by upper arm. Damage will occur. Overload Protector Your scroll saw is equipped with a 3 amp overload protection fuse. Ifyour scroll saw becomes overloaded and stops operating, turn off thescroll saw, check for a blown fuse by removing the fuse cap(Figure 11). Your scroll saw u...

Page 10 - 0 DAY NO RISK SATISFACTION GUARANTEE; TABLE; Accessories

8 30 DAY NO RISK SATISFACTION GUARANTEE If you are not completely satisfied with the performance of yourD E WALT heavy duty industrial tool, simply return it to the participating seller within 30 days for a full refund. Please return the complete unit,transportation prepaid. Proof of purchase may be...