Dewalt DW746- User Manual

Page 2 - Introduction; Launch Details; Technical Information

Introduction DW746Woodworkers Table Saw Ø Extremely accurate fence system, ensures blade parallelism in all positions,microscopic adjustment can be achieved with gentle hand pressure. Ø Powerful 2700 watt induction motor delivers high torque in ripping and crosscutting applications where tip speed m...

Page 7 - Engineering Bill Of Material; ITEM DESCRIPTION PART NO. QTY

Engineering Bill Of Material Date Created : 08/08/00 Catalogue Number : DW746-----A Type : 1 1 ITEM DESCRIPTION PART NO. QTY MARKET VARIANT 1 TABLE 389839-00 1 3 SCREW 153576-01 2 4 * TRUNNION 387164-01 1 5 SCREW 330045-39 6 6 * FRONT BRACKET 389615-00 1 7 DRIVE SHAFT 388410-00 2 8 * PIN 330036-08 4...

Page 11 - ITEM DESCRIPTION PART NO. QTY MARKET VARIANT

Engineering Bill Of Material Date Created : 08/08/00 Catalogue Number : DW746-----A Type : 1 5 ITEM DESCRIPTION PART NO. QTY MARKET VARIANT 174 BUTTON 380105-04 1 175 WASHER 330016-04 10 176 NUT WING 429901-01 2 177 BOLT 429901-02 1 178 NUT 330015-05 10 179 WASHER LOCK 98197-07 12 180 BRACKET 389918...

Page 13 - New Parts; Part Number

New Parts 250MM SAW TABLE DW746 - DE7460 - DE7461 - DE7464 Part Number Part Description CABLE TIE 149138-03 TORX WRENCH 50 152693-01 PLATE 153404-02 SLEEVE 153443-01 SCREW 153460-02 SCREW 153460-03 SCREW 153576-01 SCREW 153778-01 SERVICE TOOLING 233802-00 SERVICE TOOLING 233802-01 SERVICE TOOLING 23...

Page 34 - How to read the indicator :; EUROPEAN SERVICE SUPPORT GROUP

Equipment Needed: The following pieces of equipment are needed to properly align the saw. Description Part Number Qty C-Clamp with 5/16” shank 233802-00 1 Dial Indicator 233802-01 1 Holder with 1/4” shank 233802-02 1 Clamp with holes for 1/4” and 5/16” shanks 233802-03 1 Assembly: 1. In the indicato...

Page 36 - Raise blade height to full up position then back off a half a turn.

Page 3 BLADE ALIGNMENT CONT’D . Blade Alignment (Parallelism) at 0 ° Bevel Objective: To assure that the tolerance, from the front of the blade to the rear of the blade, (withrespect to the miter gauge slot on the right side of the table) is within designspecifications. Procedure: 1. Raise blade hei...

Page 37 - Bevel Blade to 45

Page 4 Bevel Blade to 45 ° Objective: Same as above except this time the blade is beveled to 45 ° . Procedure: 1. The allowable tolerance for the blade at 45 ° from the front of the blade to the rear is +/-.016” over 8.25”. 2. With the indicator at the front of the blade, note the needle reading. 3....

Page 38 - WORM GEAR; Bevel the saw to 0

Page 5 WORM GEAR Objective: Bevel worm should turn smoothly through entire range without binding. Procedure: 1. Bevel the saw to 0 ° and loosen the two bevel gear screws (ITEM 5) one-quarter turn. 2. Loosen left (bevel) stop screw (ITEM 3) until top of screw is flush with bottom ofmiter gauge slot. ...

Page 40 - PRODUCT PHOTOGRAPH

Page 41 - DW746 CONTRACTORS SAW - STRIPDOWN REPAIR PROCEDURE; Total Strip Down; Remove the power cable.; Removal of the legs and side panels.; to access the main

DW746 CONTRACTORS SAW - STRIPDOWN REPAIR PROCEDURE If the dust extractor (49) needs cleaning/clearing, loosen the two screws (31) and pull off fromthe shroud (29/30). To remove/ change the belt (50) turn the rise and fall handle (77) to it’s lowest point, lift themotor assembly to release the tensio...

Page 43 - Trunnion brackets

(10), spring washer (11), steel washer (9), and nylon sleeve (12). The gear will now screw outand through the trunnion bracket (6) (take care not to lose the sleeve and spacer). The bevel gear (28) is removed by taking out the two Torx 50 screws (5). Trunnion brackets If for any reason you need to r...

Table of Contents:

Summary

Other Dewalt Models