Dewalt DCF682- User Manual

Page 2 - Defi nitions: Safety Guidelines; IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR; WALT; General Power Tool Safety Warnings

1) WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and ...

Page 3 - ) POWER TOOL USE AND CARE; English

4) POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that canno...

Page 4 - ) BATTERY TOOL USE AND CARE; Additional Safety Rules for Screwdriver

• Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. • Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be cau...

Page 5 - When ordering replacement battery packs, be sure to include the; READ ALL INSTRUCTIONS

Important Safety Instructions for All Battery Packs When ordering replacement battery packs, be sure to include the catalog number and voltage. Consult the chart at the end of this manual for compatibility of chargers and battery packs. The battery pack is not fully charged out of the carton. Before...

Page 6 - The RBRCTM Seal; The RBRCTM (Rechargeable Battery Recycling Corp-

the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. • Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention. WARNING: Burn hazard. Battery liquid may be flammable if exposed to sp...

Page 8 - Indicator Light; Charge Indicators; Your tool uses a D

3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger. Indicator Light Operation PACK CHARGING PACK CHARGED x HOT/COLD DELAY PROBLEM PACK OR CHARGER Charge Indicators This charger is des...

Page 9 - Storage Recommendations; LEAVING THE BATTERY PACK IN THE CHARGER; Important Charging Notes

d. If charging problems persist, take the tool, battery pack and charger to your local service center. 4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging proce...

Page 10 - INTENDED USE; ADJUSTMENTS; WARNING: To reduce the risk of serious personal injury,

Components (Fig. 2) WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. A. Motion control activation trigger B. Lock-off switch C. LED worklight D. Battery fuel gauge E. Battery release button F. Battery pack G. Magnetic bit holder (DCF681 Only) H. Quick r...

Page 11 - OPERATION; Torque Adjustment

OPERATION WARNING: To reduce the risk of serious personal injury, turn tool off and remove the battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. CAUTION: To avoid accidental activation during transport or storage, p...

Page 12 - VARIABLE SPEED; Operation as a Screwdriver; To; To Operate; SETTING INITIAL STARTING POINT

2. Engage head of fastener with screwdriver accessory on work piece. Follow instructions for setting initial starting point. 3. Rotate your hand to the left and the screwdriver will activate in the reverse direction. To turn the tool off, release the motion control activation trigger. VARIABLE SPEED...

Page 13 - MAINTENANCE; Cleaning; CHARGER CLEANING INSTRUCTIONS

FIG. 7 MAINTENANCE WARNING: To reduce the risk of serious personal injury, turn tool off and remove the battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. Cleaning WARNING: Blow dirt and dust off of tool and cone/cut...

Page 14 - Register Online; CONFIRMATION OF OWNERSHIP:; Accessories; Since accessories, other than those offered by; Repairs; INSTALLING REPLACEMENT CUTTER ACCESSORY DWA2601IR

wire ring (P) first. Then seat cutter. When seated correctly the cutter should be flush with cone when in forward position. 4. Replace set screw. Align the tip with the hole in the cutter. Tighten firmly. CAUTION: If the set screw is lost or damaged do not replace with anything but an exact replace...

Page 15 - XXX; Three Year Limited Warranty

90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your D E WALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked. LATIN AMERICA: This warranty does not a...

Table of Contents:

Summary

Other Dewalt Models