Page 2 - Foreword; CHAPTER 1: DEFAULT SETTINGS OF PARAMETERS
Delta Temperature Controller User Manual 2007-09-17 - 2 - © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED Foreword The user manual details the process of using Delta DT series temperature controllers step by step for beginners to easily set up all kinds of parameters in a short time. CHAPTER 1: DEFAUL...
Page 3 - EFAULT; Default Settings in Temperature Controller; DTA
Delta Temperature Controller User Manual © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED - 3 - 2007-09-17 CHAPTER 1: D EFAULT S ETTINGS OF P ARAMETERS 1.1 Default Settings in Temperature Controller DTA DTB DTC Model: DTA4896R1 Model: DTB4896RR Model: DTC1000R PV SV PV SV PV SV Not connected to sensor ...
Page 4 - How to Return to Default Settings in DTA; Display
Delta Temperature Controller User Manual 2007-09-17 - 4 - © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED DTA DTB DTC Model: DTA4896R1 Model: DTB4896RR Model: DTC1000R PV SV PV SV PV SV Adjust temperature Input compensation 0.0 Password of DTC Level 1 password Disabled Level 2 password Disabled Level ...
Page 7 - DTCOM Software; How to Return to Default Settings in DTB
Delta Temperature Controller User Manual © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED - 7 - 2007-09-17 DTCOM Software Explanations Clear the user’s settings. Function address = 4724; Write data = 1234 (Please DO NOT modify this value; otherwise system confusion may occur.) After the above procedure...
Page 10 - The model adopted in this example is: DTB4896RR with firmware V1.50.; How to Return to Default Settings in DTC; Execute DTCOM Software
Delta Temperature Controller User Manual 2007-09-17 - 10 - © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED DTCOM Software Explanations Clear the user’s settings. Function address = 474E; Write data = 1234 (Please DO NOT modify this value; otherwise system confusion may occur.) After the above procedur...
Page 11 - Return to default settings; ONTROL; for 3 seconds
Delta Temperature Controller User Manual © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED - 11 - 2007-09-17 DTCOM Software Explanations Function address = 472A; Write data = 1234 (Please DO NOT modify this value; otherwise system confusion may occur.) Clear the user’s settings. Function address = 474E;...
Page 13 - Parameters relevant to ON/OFF control
Delta Temperature Controller User Manual © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED - 13 - 2007-09-17 Parameters relevant to ON/OFF control Press in the main screen of DTA to enter the “regulation mode”. Display Explanations PV SV Status of the temperature controller or Set up hysteresis. Defau...
Page 14 - Parameters relevant to PID control
Delta Temperature Controller User Manual 2007-09-17 - 14 - © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED Display Explanations PV SV Status of the temperature controller The control modes include: PID, ON/OFF, MANUAL. Default = PID. Select “PID” here. Back to top Press to return to the main screen. ...
Page 17 - Parameters relevant to MANUAL control
Delta Temperature Controller User Manual © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED - 17 - 2007-09-17 Display Explanations PV SV Status of the temperature controller The control modes include: ON/OFF, MANUAL, PID and PID PROG. Default = PID. Select “MANUAL” here. Back to top Press to return to th...
Page 20 - Parameters relevant to PID PROG control
Delta Temperature Controller User Manual 2007-09-17 - 20 - © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED Display Explanations PV SV Status of the temperature controller + Remaining time in the current step + Target temperature for the current execution + The pattern currently executed Parameters r...
Page 21 - PV; Next, open DTCOM Software and switch to ON/OFF control mode.
Delta Temperature Controller User Manual © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED - 21 - 2007-09-17 Display Explanations PV SV Status of the temperature controller Set up the position of decimal point Key-locked function Output volume. In PID PROG control mode, this is a read-only parameter and...
Page 22 - default values are “0”.
Delta Temperature Controller User Manual 2007-09-17 - 22 - © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED Set up hysteresis. Default = heating hysteresis. Can be set as cooling hysteresis as well. Both default values are “0”.
Page 23 - Switch the control mode to MANUAL mode.
Delta Temperature Controller User Manual © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED - 23 - 2007-09-17 4.2 MANUAL Switch the control mode to MANUAL mode. Set up heating or cooling control cycle. Default = heating, 20 seconds per cycle. Manually adjust the output percentage. Assume the percenta...
Page 24 - Switch the control mode to PID mode
Delta Temperature Controller User Manual 2007-09-17 - 24 - © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 4.3 PID Switch the control mode to PID mode You can conduct auto-tuning on the default PID parameters according to the environment where your equipment is in or its temperature control capabili...
Page 25 - Switch the control mode to PID PROG mode
Delta Temperature Controller User Manual © DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED - 25 - 2007-09-17 4.4 PID PROG Switch the control mode to PID PROG mode The 64 steps come from the combination of 8 patterns and 8 steps for each pattern. You can establish maximum 64 steps according to differen...