Delta DNS100 - Manual - manualsarea.com

Page 3 - SAFETY GUIDELINES / DEFINITIONS; SAVE THESE INSTRUCTIONS!; IMPORTANT SAFETY INSTRUCTIONS

3 indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 Fig. 6 Fig. 5 Fig. 2 Fig. 3 Fig. 4 1. Read and understand tool labels andmanual. Failure to follow warnings could result in DEATH or SERIOUS INJURY . Fig. 1. 2 . Operator and others in work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSIZ87.1 requirements...

Page 7 - Use approved Delta fasteners only.; POWER SOURCE; EMPLOYER’S RESPONSIBILITIES

7 Employer must enforce compliance with the safety warnings and all otherinstructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understandtool labels and manual. Failure to fol...

Page 8 - PREPARING THE TOOL; fasteners with points down in the magazine.

8 Fig. 19 Fig. 18 Fig. 21 Fig. 23 A Fig. 22 A Fig. 20 PREPARING THE TOOL 1. After reading and understanding this entire manual, connect tool to air supply (Fig. 18). 2. Depress latch and slide magazine cover open (Fig. 19). 3. Insert a strip of approved fasteners (Fig. 20 and/or Fig. 20A). Orient fa...

Page 9 - USING THE TOOL; “single sequential actuation”; OPERATING INSTRUCTIONS

9 USING THE TOOL Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a “single sequential actuation” trigger. To fire, grip the tool firmly to maintain control, position nose of tool onto work surface, push the tool firmly against work surface t...

Page 10 - RUBBER NOSE CUSHION; Disconnect tool from air supply before removing or re-

10 The depth to which a fastener is driven is controlled by the depth adjustmentknob (A) Fig. 25. The depth of drive is factory adjusted to a nominal setting.Test fire a fastener and check depth. If a change is desired, rotate theadjustment knob (A) Fig. 25. The adjustment knob has detents every 1 /...

Page 11 - CLEARING A JAMMED FASTENER; Disconnect tool from air supply.

11 CLEARING A JAMMED FASTENER Disconnect tool from air supply. 1. Open magazine and remove remaining fasteners (Fig. 28 and Fig. 29). Remove fasteners from tool before opening the fastener guide plate. Fasteners are under pressure and may shootout of magazine which could cause injury. 2. Open the qu...

Page 12 - CLEAN AND INSPECT DAILY; D i s c o n n e c t t o o l f r o m a i r s u p p l y b e f o r e c l e a n i n g a n d; SERVICE AND REPAIRS; MAINTENANCE

12 CLEAN AND INSPECT DAILY D i s c o n n e c t t o o l f r o m a i r s u p p l y b e f o r e c l e a n i n g a n d inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammablecleaning solutions to wipe exterior of tool only i...

Page 13 - TROUBLESHOOTING; Disconnect tool from air supply before performing any Service

13 TROUBLESHOOTING Disconnect tool from air supply before performing any Service Procedure. SYMPTOM PROBLEMS SOLUTIONS 1. Air leak near top of Loose screws. Tighten screws. tool or in trigger area. Worn or damaged Install Overhaul Kit. o-rings or seals. 2. Tool does nothing or Inadequate air supply....

Page 14 - ACCESSORIES; Two Year Limited New Product Warranty

14 A complete line of accessories is available from your Porter-Cable • DeltaSupplier, Porter-Cable • Delta Factory Service Centers, and Delta AuthorizedService Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of your nearest supplier. Since accessories, other...

Delta DNS100 - Manual

Table of Contents:

Summary

Other Delta Models