Delta 36-412 - Manual - manualsarea.com

Page 3 - SAFETY GUIDELINES - DEFINITIONS; CONSTRUCTION ACTIVITIES; CALIFORNIA PROPOSITION 65

3 Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY, READ THE INSTRUC-TION MANUAL BEFORE OPERATING THEMACHINE. Learning the machine’s application, limitations, and specific hazards will greatly mini-mize the possibility of accidents and injury. 2. USE CERTIFIED SAFETY EQUIPMENT. Eye protection equipment s...

Page 5 - ADDITIONAL SAFETY RULES FOR MITER SAWS; Refer to them often; SAVE THESE INSTRUCTIONS

5 ADDITIONAL SAFETY RULES FOR MITER SAWS Refer to them often and use them to instruct others . FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY. SAVE THESE INSTRUCTIONS . 1. DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. Amachine i...

Page 6 - IN ALL CASES, MAKE CERTAIN THE; POWER CONNECTIONS

6 A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will...

Page 7 - EXTENSION CORDS; MINIMUM GAUGE EXTENSION CORD; FOREWORD; FUNCTIONAL DESCRIPTION; UNPACKING AND CLEANING

7 EXTENSION CORDS Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding typeplug and matching receptacle which will accept themachine’s plug. When using an extension cord, be sureto use one heavy enough to carry the...

Page 8 - “MOVING CUTTINGHEAD TO THE; ASSEMBLY; ASSEMBLY TOOLS REQUIRED

8 B Fig. 3A A Fig. 4A A B Fig. 3 C D A B Fig. 4 With the cuttinghead in the up position, attach the dustshroud (A) Fig. 4A to the port (B) with three screws usingthe supplied wrench. NOTE: Installation is easier if you place a screw on the wrench and then place it in the hole. ATTACHING DUST BAG 1. ...

Page 9 - MOVING TABLE TO THE 0° CUT-OFF POSITION; “ROTATING TABLE FOR MITER CUTTING”,; “ADJUSTING SLIDING FIT BETWEEN MOVABLE TABLE AND BASE.”; FENCE OPERATION

9 Fig. 5 A C E D E Fig.6 MOVING TABLE TO THE 0° CUT-OFF POSITION 1. Rotate the locking knob (A) Fig. 5 counter-clockwise as far as it will go. Depress the lever (B) and rotate the table(C) to the 0 ° straight cut-off position, release the lever (B), and tighten the locking knob (A). NOTE: This saw i...

Page 10 - OPERATIONS; STARTING AND STOPPING MACHINE; OPERATIONAL CONTROLS AND ADJUSTMENTS

10 Fig. 12 B Fig. 11 A A A FASTENING MACHINE TO SUPPORTINGSURFACE Before operating your compound miter saw, firmlymount it to a workbench or other supporting surface.Four holes (A) Fig. 9 are provided for fastening the sawto a supporting surface. When frequently moving the saw from place to place,mo...

Page 11 - D E; ROTATING TABLE FOR MITER CUTTING

11 Fig. 16A C A Fig. 16 D A D C B A B C D E G 1. The compound miter saw will cut any angle from a straight 0° cut to 48° right and left. Turn the locking knob (A) Fig.13 counterclockwise, depress the lock lever (B), and rotate the table to the desired position. 2. This machine is equipped with posit...

Page 12 - TABLE HAZARD ZONE; THE AREA INSIDE THE TWO RED; TILTING CUTTINGHEAD FOR BEVEL CUTTING; DISCONNECT MACHINE FROM P O W E R S O U R C E .

TAKE CARE NOT TO PINCH THE CORD (A) FIG. 23A WHEN TILTING THE CUTTINGHEAD. IMPORTANT: Move the sliding fences to provide clearance for the blade and guard. The DEGREE of tilt determines how far to move the sliding fences. Refer to the section “fence OPERATION.” Fig. 22 12 Fig. 18 Fig. 21 A A TABLE H...

Page 13 - SELECTING 0°, 33.9°AND 45° BEVEL POSITIVE STOPS; DISCONNECT THE MACHINE FROM THE POWER SOURCE.

13 The bevel setting feature utilizes a sliding plate (A) Fig. 24,pin (B), and bushing (C) design that is used to select thebevel angle. The position of the pin (B) and the sliding plate(A) determine the bevel angle. DISCONNECT THE MACHINE FROM THEPOWER SOURCE. 1. Position the bevel detent plate so ...

Page 15 - “TABLE HAZARD ZONE” SEE FIG.; AUXILIARY WOOD FENCE; only; MACHINE USE

15 Fig. 35 B C D Fig. 36 C D A B ADJUSTING LOWER BLADE GUARD The 36-412 incorporates an moveable lower blade guard (C) Fig. 36, and it also has a secondary blade guard (B) tocover the rear section of the blade. After an extended period of use, the moveable lower blade guard (C) Fig. 36 maynot operat...

Page 16 - CUTTING BOWED MATERIAL; CORRECT; CUTTING ALUMINUM; NEVER APPLY LUBRICANT TO THE BLADE WHILE THE SAW IS RUNNING.; AUXILIARY FENCE SPACER

Fig. 41 CORRECT CUTTING BOWED MATERIAL 1. Check the workpiece. If it is bowed, position the workpiece on the table as shown in Fig. 41. 2. When the workpiece is positioned the wrong way (Fig. 42), it will pinch the blade near the completion of the cut. Fig. 39 Fig. 40 FENCE FENCE BLADE BLADE 16 CORR...

Page 18 - CEILING EDGE

Fig. 46C Fig. 46D C B A D A NEW FEATURE FOR THIS TOOL IS CROWN MOULDING STOPS BUILT INTO THE BASE. DELTA DOESNOT CONSIDER THE CROWN MOULDING STOPS TO BE WORK CLAMPS AND THEY ARE NOT TO BE USED IN THIS MANNER. MAKE SURE THAT THE FENCES ARE CLEAR OF THE GUARD AND BLADE BEFORE OPERATING THE SAW. WHEN C...

Page 19 - OTHER ANGLES; TROUBLESHOOTING; KEEP MACHINE CLEAN; PROTECTING CAST IRON FROM RUST

19 Fig. 49 Fig. 50 5. Place the crown moulding on the table with the WALL EDGE of the crown moulding against the fence and make the cut. Again, the piece of crown mouldingused for the outside corner will always be on the rightside of the blade, as shown at (C) Fig. 48. The pieceof crown moulding use...

Page 20 - CHANGING THE BLADE; Do not remove the inside; teeth of saw blade are pointing down at the front,; OVER-TIGHTENING THE NUT COULD IMPAIR GUARD MOVEMENT.

20 CHANGING THE BLADE The 36-412 incorporates a moveable lower blade guard, and it also has a secondary blade guard to cover the rearsection of the blade. Make sure there is minimal gap between the two guards when the cuttinghead is in its uppermostposition. Fig. 52 E G C D H J Fig. 53 F 1. Use only...

Page 21 - BRUSH INSPECTION AND REPLACEMENT; PARTS, SERVICE OR WARRANTY ASSISTANCE; ACCESSORIES

Fig. 55 B C Fig. 54 A A BRUSH INSPECTION AND REPLACEMENT BEFORE INSPECTING BRUSHES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies, depending on the load on the motor. Check the brushes after the first 50 hours, or after a new set ofbrushes has been installed. After the first check,...

Page 22 - Two Year Limited New Product Warranty; WARRANTY

22 Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessorywhich in normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a Delt...

Page 23 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...

Delta 36-412 - Manual

Table of Contents:

Summary

Other Delta Models