Delta 36-220 - Manual

8 Fig. 12 Fig. 11 Fig. 10 Fig. 9 ASSEMBLING ACCESSORYWORK CLAMP TO SAW 1. The work clamp (A) Fig. 9, can be used on either the right or left side of the saw base. Insert post of workclamp into the hole located on the front of the saw base,as shown. Work clamp 36-221 is available as a accesso-ry. (Se...

9 STARTING ANDSTOPPING SAW To turn the saw “ON” push in on switch lock key (A) Fig. 13, and depress switch trigger (B). To turn the saw “OFF” release switch trigger (B). Your compound miter saw is equipped with an automaticelectric blade brake. As soon as the switch trigger (B)Fig. 13, is released, ...

11 Fig. 18 LOCKING CUTTING ARMIN THE DOWN POSITION When transporting the saw, the cutting arm shouldalways be locked in the down position. This can beaccomplished by lowering the cutting arm (A) Fig. 18, andmoving the locking lever (B) to the locked position, asshown. IMPORTANT: NEVER CARRY THE COM-...

12 Fig. 22 Fig. 21 ADJUSTMENTS ADJUSTING 90 AND 45DEGREE BEVEL STOPS 1. DISCONNECT THE SAW FROM THE POWER SOURCE . 2. Loosen bevel lock handle and tilt the cutting arm all the way to the right and tighten the bevel lock handle. 3. Using a square (A) Fig. 21, place one end of the square on the table ...

13 Fig. 26 ADJUSTING BLADEPARALLEL TO TABLE SLOT 1. DISCONNECT THE SAW FROM THE POWER SOURCE . 2. NOTE: This adjustment should be checked with the cutting arm moved all the way to the right (blade 90degrees to the table). 3. Lower the cutting arm. The saw blade (A) Fig. 25, should be parallel to the...

14 Fig. 28 Fig. 29 7. Loosen the two fence locking screws, one of which is shown at (A) Fig. 28, and move the fence (B) all the wayto the rear position, as shown. Then tighten the two fencelocking screws (A). 8. Using a square, place one end of the square against the blade and the other end against ...

15 Fig.31 Fig. 32 Fig. 33 ADJUSTING DOWNWARDTRAVEL OF SAW BLADE 1. DISCONNECT THE SAW FROM THE POWER SOURCE . 2. The downward travel of the saw blade can be limited to prevent the saw blade from contacting any metal sur-faces of the machine. This adjustment is made by loos-ening locknut (A) Fig. 31,...

16 Fig. 34 Fig. 35 Fig. 36 9. Fig. 34, illustrates the work clamp (B) being used to firmly hold the workpiece against the fence. 10. Fig. 35, illustrates the cuttinghead tilted and the armin a miter position for a compound miter/bevel cuttingoperation. 11. Fig. 36, illustrates the fence in the forwa...

17 Fig. 37 Fig. 38 Fig. 39 When performing multiple or repetitive cut-off operationsthat result in small cut-off pieces, one inch or less, it ispossible for the saw blade to catch the cut-off pieces andproject them out of the machine or into the blade guardand housing, possibly causing damage or inj...

18 Fig. 43 MAINTENANCE CHANGING THE BLADE WARNING: USE ONLY CROSS-CUTTING SAW BLADES. WHEN USING CARBIDE TIPPED BLADES,MAKE SURE THEY HAVE A NEGATIVE HOOK ANGLE.DO NOT USE BLADES WITH DEEP GULLETS ASTHEY CAN DEFLECT AND CONTACT GUARD . 1. DISCONNECT THE SAW FROM THE POWER SOURCE . 2. Rotate lower bl...

20 Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin normal use has proven to be defective in workmanship or material, provided that the customer returns the product pre-paid to a Delta factory service center or authorized s...

The following are trademarks of PORTER-CABLE • DELTA Corporation (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER ® , INNOVATION THAT WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER-CABLE ® , QUICKSAND ® , SANDTRAP ® , SAW ...