Delta 34-814 - Manual

6 OPERATING INSTRUCTIONS FOREWORD The Delta Unisaw is a 10" right tilting arbor saw. The Delta Unisaw features set the standards in the table saw industry. UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromal...

7 ASSEMBLY INSTRUCTIONS WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE SAW TO THE POWER SOURCE UNTIL THE SAW IS COMPLETELY ASSEMBLED AND YOU UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. ASSEMBLING BLADETILTING MECHANISMHANDLE 1. Install fiber washer (A) Fig. 3, on the blade tilting mechanism shaft (B...

12 Fig. 28 Fig. 30 E Fig. 29 FASTENING MOTOR CORD TO SAW FRAME 1. IMPORTANT: Turn the blade tilting handwheel counterclockwise as far as it will go until the saw blade isin the 45 degree position. 2. IMPORTANT: Turn the blade raising and lowering handwheel counterclockwise until the blade is at itsl...

14 OPERATING CONTROLS AND UNISAW ADJUSTMENTS STARTING AND STOPPING THE SAW To start the machine, push “ON” button (A) Fig. 39. Tostop the machine, push “OFF” button (B). Fig. 39 A B LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the machine is not in use, the switch should be locked in the “OF...

15 ADJUSTING 90 AND 45DEGREE POSITIVE STOPS Positive stops are provided to quickly and accuratelyposition the blade at 90 and 45 degrees to the table. Tocheck and adjust the positive stops, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Raise the saw blade all the way to the top and tu...

17 MAINTENANCE CHANGING THE SAW BLADE 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. NOTE: Two wrenches are supplied with the saw for changing the saw blade; a box end wrench and open endwrench. 3. Remove table insert and raise saw blade to its maximum height. 4. Place the open end wrench (B) Fig. 50, ...

18 PROTECTING CAST IRON TABLE FROM RUST To clean and protect cast iron tables from rust, you will need the following materials: 1 pushblock from a jointer, 1 sheetof medium Scotch-Brite™ Blending Hand Pad, 1 can of WD-40 ® , 1 can of degreaser, 1 can of TopCote ® Aerosol. Apply the WD-40 and polish ...

19 Fig. 56 A Fig. 57 B Fig. 58 USING THE FENCE AS ACUT-OFF GAGE WARNING: WHEN USING YOUR UNIFENCE AS A CUT-OFF GAGE, MAKE SURE IT IS PROPERLY SETUP AS DESCRIBED HERE. The fence can be used as a cut-off gage when crosscutting a number of pieces to the same length. IMPORTANT: When using the fence as a...

23 CONSTRUCTING A FEATHERBOARD Fig. 74, illustrates dimensions for making a typical featherboard. The material which the featherboard is constructedof, should be a straight piece of wood that is free of knots and cracks. Featherboards are used to keep the work incontact with the fence and table and ...

24 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a p...

25 BLADE GUARD ACCESSORIES Deluxe Uniguard ® Blade Guard The Delta Model 34-976 Uniguard Blade Guard withSplitter and Anti-kickback Fingers Fig. 77, is anaccessory that can be used in place of the standardblade guard that is supplied with the Unisaw. The DeltaModel 34-976 Uniguard Blade Guard can be...

26 Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a Delta factory servic...

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER ® , INNOVATION THAT WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER- CABLE ® , QUICKSAND ® , SANDTRAP ® , SAW BOSS ® , SPEE...